20 Most Recent 2006 Yamaha Ybr 125 Diversion Questions & Answers

No if you know what you are suppose to be doing, a hairy event for first timer, because you have to remove axle nut, adjusting puller nut, brake torque nut on both side and ensure when you put them back together the are aligned. Good enough?

If the engine is turning over when you kick it but wont fire. The first thing to check is the spark plug. if the spark plug is rusted, corroded, or black replacing it should resolve the problem.

i have lost my motor cycle keys

heres a link to the owners manual - everything you need to know is there under SPECIFICATIONS, http://ymenvom.nl/manuals/U3D9E0.PDF

Left hand bolts are not common on modern motorcycles. So, to loosen, turn counterclockwise. To tighten, turn clockwise.

They will to be drilled need out.


Please rate this solution

Under well-lit conditions, look for any signs of punctures (such as nails or shards of glass) which might potentially lead to a loss of pressure or a blowout. Bulging or cracking might also occur on old tires; make sure you roll your bike forward in order to see all surface areas that come in contact with the road.

its very common for the fuel outlet in the tank to get plugged with debris

You dont say what bike it is, as a guess broken throttle cable

YES IT PLUGS INTO BACK OF HEADLIGHT

if you are trying to install spark plug wires you will have to remove the gas tank. take care and use safety glasses when handling gas and chemicals.

Clean the carburetor. Pay special attention to the jets inside the float bowl area. Remove the throttle and air screws and spray cleaner into the holes and every other hole in the body of the carb. Remount the carb then screw the throttle and air screws inward until they LIGHTLY seat. Now open each of them one and one half turns. If the bike still wants to speed up the idle on its' own, the seals and rubber fittings between the carb and the cylinder are not sealing out the outside air. New seals etc., are needed.

If you look carefully at the brake switch there is a spring mechanism on it, make sure that is moving freely when you apply the brakes.Also the switch can be adjusted to move up or down according to your need,there is a screw like around its body which can be adjusted(more most models this apply).Else you need to play around with the little metal attached to the switch and brake lever..Do not worry it is very easy to solve but be careful not to brake the metail attachment..Hope this helps.

im unsure but arent they on the sterering stem on a metal stamp or perhaps under the gear shifter I am unsure

This is a highly ill - eagle act to do. In the old days we would put an electric drill on the drive cable, but now they make them tamper proof so they only go one way. The bezels are crimped on so you can't get inside them. I expect modern one may be electronic. How will your insurance company know what mileage you have done? I have never known an insurance cancel or fine due to mileage. You should have just disconnected it when you got close to the limit. Buy a used one and use them for 6 months in turns. There are two or three here 23K and one with 36k https://www.google.com/search?q=2002+yamaha+sr125+speedometer ..

Not mentioned in the Service manual http://www.badrad600.com/Yamaha_Radian_Factory_Service_Manual_OCR.pdf https://www.google.com/search?q=1986+Yamaha+YX600+Radian+remove+USA+speed+restriction Something like this?

Removing 95bhp restriction ' Yamaha Star Cycle V-Max ...

vmaxforum.net https://www.vmaxforum.net > threads > removing-95bh... Jan 14, 2013 - Air jets could easily become blocked. Step 3: Removing the speed restriction. On the back of the speedo-needle a disc with two different . ..

Check the diagrams here https://www.google.com/search?q=yamaha+sega+81+firing+order ..

Question edited for a lot more clarity, add maker. Question moved to Yamaha Motorcycle. Unlikely to be a carburetor problem as this appears to be fuel injected! https://www.google.com/search?q=Yamaha+Mio+125+MX+no+start ..