Top 20 2001 Yamaha XV 1600 Wild Star Questions & Answers

replace ignition drilling out ignition set off your security system and by passing the components will not work it will cause more damage this is why you dont try to hot wire any vehicle

what ever chapter on your clymer manual--I think most stuf is nonadjustable on carbs

only use motorcycle oil, if it has a wet clutch, car oils have friction modifiers that can affect clutches

go to www.roadstarclinic.com good source for all kinds of information on service for that bike.

Forgive me for saying, but if you are having problems with your chain on the XV1600 Wildstar, then you have a BIG problem...

It's belt drive!

Your Yamaha dealer can do it for you if you have a full license.

Hi, sounds like,the battery does not have enough charge to turn over the motor,thats when you get the clicking noise,,,give the battery a good charge and you will be ok.

This is a highly ill - eagle act to do. In the old days we would put an electric drill on the drive cable, but now they make them tamper proof so they only go one way. The bezels are crimped on so you can't get inside them. I expect modern one may be electronic. How will your insurance company know what mileage you have done? I have never known an insurance cancel or fine due to mileage. You should have just disconnected it when you got close to the limit. Buy a used one and use them for 6 months in turns. There are two or three here 23K and one with 36k https://www.google.com/search?q=2002+yamaha+sr125+speedometer ..

Not mentioned in the Service manual http://www.badrad600.com/Yamaha_Radian_Factory_Service_Manual_OCR.pdf https://www.google.com/search?q=1986+Yamaha+YX600+Radian+remove+USA+speed+restriction Something like this?

Removing 95bhp restriction ' Yamaha Star Cycle V-Max ...

vmaxforum.net https://www.vmaxforum.net > threads > removing-95bh... Jan 14, 2013 - Air jets could easily become blocked. Step 3: Removing the speed restriction. On the back of the speedo-needle a disc with two different . ..

Check the diagrams here https://www.google.com/search?q=yamaha+sega+81+firing+order ..

Question edited for a lot more clarity, add maker. Question moved to Yamaha Motorcycle. Unlikely to be a carburetor problem as this appears to be fuel injected! https://www.google.com/search?q=Yamaha+Mio+125+MX+no+start ..

It isn't called a Magneto, that was for really old bikes. It is a 'stator'. Service manual https://drive.google.com/drive/folders/1OFbBW2YhLpL1-Xbsw9vexi84Y7aXGTdG Parts List https://www.cmsnl.com/yamaha-rt100-1990-l-usa_model9624/partslist/ https://www.google.com/search?q=1990+yamaha+rt100+wiring+diagram ..

First make sure that the new battery has been fully charged and is not defective. Next make sure that the proper voltage is reaching the started. You may have a bad post connection or loose connection at the starter. Try jumping you battery with another known good battery.

Make sure the fuel is getting to the valve and passing through it. Possible blockage in fuel line or in the tank.

Above the master cylinder on each brake.

What Exactly does the bike do when it 'loses power'? This will give clues as to where the issue could be. When was the last time the bike was given a major service? Sometimes it can be as simple as a dirty fuel/air filter or an old/worn or dirty spark plug.

1. Fuel System Issues:
   • Check the fuel system for clogs, such as a dirty fuel filter or carburetor jets.
   • Ensure that the fuel tank and fuel lines are clean and free from debris.
   • Consider adding a fuel system cleaner to help clean out any deposits.
2. Ignition System Problems:
   • Inspect the spark plugs for fouling, wear, or improper gap.
   • Check the ignition timing to make sure it's set correctly.
   • Inspect the ignition coils and wiring for any loose connections or damage.
3. Air Intake and Exhaust Issues:
   • Examine the air filter for clogs or dirt that may restrict airflow.
   • Inspect the exhaust system for any leaks or blockages.
4. Vacuum Leaks:
   • Check for vacuum leaks in hoses, gaskets, or intake boots. A vacuum leak can cause an improper air-fuel mixture, leading to backfiring.

Are you wanting the size of the hex bolt head or the thread size and bolt length? Most oil pan plug bolts are either 17mm (5/8th socket) or 19mm (3/4" socket) bolt heads.