20 Most Recent 1996 Yamaha FZX 250 Zeal Questions & Answers


Hi, Anonymous for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
1996 Yamaha FZX 250 Zeal wiring diagram Google Search
Yamaha Motorcycle Wiring Diagrams
http://vdj84.hol.es/yamaha-fzx-250-manual.pdf
OEM parts for Yamaha
Yamaha FZX250 Zeal Owners Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1996 Yamaha FZX... | Answered on Feb 13, 2017


My 1994 Yamaha Timberwolf starts but won't idle properly. Sometimes when it quits it backfires. What could the problem be?

1996 Yamaha FZX... | Answered on Sep 15, 2011


Hi, Terrey and the usual suspects are:
1. Fouled spark plugs.
2. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead acid batteries.
3. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Loose connection at ignition coil or plug between ignition sensor and module.
5. Spark plug cables in bad condition, shorting/leaking, spark plug cable connections loose check for spark leakage in the dark.
6. Faulty ignition coil or electronic control module.
7. Faulty CKP, CMP, or BAS sensor.
8. Faulty ignition switch.
9. Tilt sensor needs a reset.
10. Security alarm failing to disarm needs reset
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
1 or 2 cylinders not firing sometimes
cylinders 1 and 4 not firing idles cuts out with throttle
Manuals Data Zealous
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-fz-owners-manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Yamaha FZX 250... | Answered on Jun 04, 2017


Hi, Barry and the usual suspects are:
1. Fuel cap or fuel tank is not venting properly.
2. Fuel filter clogged.
3. Fuel line pinched or kinked.
4. Float needle and seat sticking.
5. Float level too low.
6. Carburetor bowl vent line clogged/blocked/pinched.
7. Idle adjusting screw set too low.
8. Air/fuel mixture screw set too lean.
9. Idle port, transfer ports, slow air jet clogged.
10. Slow fuel jet clogged.
11. Faulty fuel pump.
For more information about your issue and valuable "Free" downloads that you will need please Click on blue links below. Good luck and have a wonderful day.
Yamaha zeal 250 stalling and problem with warm starting
1999 Yamaha Zeal aka FZX 250 will not idle
https://netrider.net.au/threads/looking-for-a-fzx250-zeal-service-manual.102959
OEM parts for Yamaha
Manuals Data Zealous

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Yamaha FZX 250... | Answered on Feb 22, 2017


Hi, Anonymous for this scenario you will need your service/owners/ manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere zero $ you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Newbie Question Removing Yamaha FZX250 seat
https://www.perthstreetbikes.com/forum/showthread.php?t=126965
Manuals Data Zealous
OEM parts for Yamaha

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

Yamaha FZX 250... | Answered on Dec 21, 2016


Fit a new seal kit from http://litetek.co/Carb_Kit_Yamaha_Zeal.html

Yamaha FZX 250... | Answered on Aug 30, 2013


If your rings were shot and the engine was running you would see billows of blue smoke coming out the pipes, as well as oil. If not running, then your fuel would end up in your sump inflating the amount of oil in there. (this does happen on all bikes only ridden around town, get it out on the highway to burn off the excess fuel then recheck your oil level.)
I'm wondering if you left your fuel tap on overnight (if it has one) if so, then you will have fuel running back out either the carbs or the boot that goes from the carb to the engine. Oil will leak if your valve seals are shot. it is possible that it was only fuel that was stained with a bit of oil.

Yamaha FZX 250... | Answered on Sep 17, 2011


Sounds like lack of fuel to the engine. Has the bike been sitting for some time? You may want to pull the carburetor and give it a good cleaning payning particular attention to the jets. Don't use anything made of steel to clean your jets because you'll run the risk of enlarging and ruining them. I've had success using either wooden toothpicks (for large jets) or copper wire (small jets). Make sure you take your time and work very carefully when cleaning them; if you rush, you can end up with something broken off into a jet orifice and having to buy new ones.

Yamaha FZX 250... | Answered on Jun 25, 2011


Hi, Anonymous the vast majority of service, parts fiche, and owners manuals on the internet are "FREE" to download and all service manuals contain wiring diagrams in the back pages. The rest usually charge a modest fee of $15 and there is a handful of obscure, rare, obsolete, and very old models that are no longer or never were available and some were never printed in English. The Indian and Philippine markets are usually in E-book format only, for these rare occasions I shall look on eBay and find the cheapest one available. Most of the manuals will cover your exact make, model, and year otherwise one will be provided that comes as close as possible to your bike and will have most of the same info that an exact manual would have. If there is no $ sign after the manual link it is free to download.
To download your manual for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://biobug.org/motorcycle/xs850/Yamaha-XS70-XS850-Service-Manual.pdf
https://www.partsfish.com/page/oem-parts-for-yamaha
http://mybikemanuals.com/yamaha/
https://bikez.com/motorcycles/yamaha_xs_750_special_1981.php
https://en.wikipedia.org/wiki/Yamaha_XS750

Yamaha... | Answered Yesterday


Hi, Chet for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Yamaha, despair not, for a mere zero $ you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?q=Wiring+diagram+1981+Yamaha+XJ750+Seca&tbm=isch&source=univ&sa=X&ved=2ahUKEwjP6Ybv8N3lAhWKv1kKHRc4DQcQsAR6BAgFEAE&biw=1440&bih=757
http://classiccycles.org/1852/597985.html
https://www.xjcd.org/book/export/html/77
https://www.partsfish.com/page/oem-parts-for-yamaha
http://mybikemanuals.com/yamaha/

Yamaha... | Answered 2 days ago


Should be around 120 to 130 at cranking should have a decompression valve that brings it down to that, running it's around 170 to 180

Yamaha... | Answered on Nov 03, 2019


Hi, Aron before testing any electrical component in the Turn Signal Light Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test because your battery may have 12.5 volts or more but little or zero amps causing the battery to be faulty and must be replaced, "AGM" batteries fall into this category more so than lead-acid types, also before diagnosing any turn signal/running light/parking light issue make sure the bulb is good and the light fuse has continuity with a test light. If you have replaced your OEM lights with one or all LED lights you are going to need a load equalizer.
If no turn signals are working the cause could be a faulty turn signal module/flasher or the connector going to it, look for corroded, loose, or broken pins/sockets. Contact spray cleaner is great for removing corrosion.
If your turn signal comes on but takes several seconds before it starts flashing you may have dirty contacts in the turn signal switch/button, the switch needs to be opened up and cleaned also the flasher may be starting to fail. It should be noted that cold weather will only exacerbate the situation especially when temperatures drop down below freezing and the location of the component, turn signal switches on the handlebar are at the mercy of the oncoming freezing 70 mph wind and makes it hard for the contacts to do their job covered in frozen grease/grime
If all four turn signals flash at the same time like hazard lights even though you only pressed one turn signal button then you have a LED light in the circuit and need a load equalizer that can be purchased from any motorcycle parts supplier.
If your speedometer does not function properly it will have to be fixed first because your turn signal module gets the data from the speedometer for normal turn signal function.
If your front turn signals don't work use a test light to check for power and ground at the bulb socket, then start backtracking the wiring through every wire connector to the turn signal switch/button and check for continuity, go all the way back to the fuse if necessary to find the cause of the malfunction.
If your rear turn signals don't work check your rear fender wiring harness connector first, look for, corroded, broken, loose pins/sockets, power, and a good ground, the harness connector is usually located under the seat on the front of the rear fender then keep tracing the wiring look for obvious harness damage caused by the rear tire.
If you still can't find the malfunction backtrack from the rear fender wiring harness connector.
If one side does not work you could have a faulty turn signal switch or module check for continuity.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.motorcyclecruiser.com/basic-electronic-troubleshooting/
https://www.motorcyclenews.com/new-rider/choosing-kit/2011/august/aug3011-why-do-bulbs-keep-blowing-/
http://www.family-motorsports.net/GY6-50cc-150cc.pdf
https://www.partsfish.com/page/oem-parts-for-yamaha
http://www.yamaha-motor.com.my/wp-content/uploads/2019/01/BC1-Nmax-EN.pdf

Yamaha... | Answered on Nov 01, 2019


Hi, Jose for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Yamaha, despair not, for a mere zero $ you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?q=Wiring+diagram+1975+Yamaha+DT+400&tbm=isch&source=univ&sa=X&ved=2ahUKEwjezcXm-cTlAhWSuVkKHW2ZDfsQsAR6BAgJEAE&biw=1440&bih=757
https://yamaha-enduros.com/index.php/forum/74-76-twin-shock/1232-1975-dt400-wiring
http://classiccycles.org/1852/597985.html
https://www.manualslib.com/manual/999370/Yamaha-Dt250d.html
https://www.partsfish.com/page/oem-parts-for-yamaha
http://mybikemanuals.com/yamaha/

Yamaha... | Answered on Oct 30, 2019


Hi, Anonymous for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Yamaha, despair not, for a mere zero $ you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?q=Wiring+diagram+1973+Yamaha+DT3&tbm=isch&source=univ&sa=X&ved=2ahUKEwjqnNPkmsPlAhVjpVkKHfkICfEQsAR6BAgIEAE&biw=1440&bih=757
http://classiccycles.org/1852/597985.html
https://www.google.com/search?q=1973+yamaha+dt3+service+manual&source=univ&tbm=shop&tbo=u&sa=X&ved=0ahUKEwj7kpjIm8PlAhXErVkKHTh9BvwQsxgILw&biw=1440&bih=757
https://www.partsfish.com/page/oem-parts-for-yamaha
http://mybikemanuals.com/yamaha/

Yamaha... | Answered on Oct 30, 2019


It should be possible to test the pump for proper function - there should be no need to replace it hoping for a cure.

A fuel pump should suck at one end and blow at the other and this can be measured using appropriate gauges and if those measurements are satisfactory the amount of fuel pumped can be measured...

Such tests are fairly routine on wheeled vehicles and not only are they a valuable aid to correct diagnosis they remove all doubt when warranty work is involved.

Yamaha... | Answered on Oct 27, 2019


Contact your supplier, they should give support to you.
For example, if users who buy diesel generator set with us, if they have maintenance question or fault, we will tell them the solutions.
This is suport website: www.dieselgeneratortech.com

Yamaha... | Answered on Oct 26, 2019


If you investigate on the sides of the tires there is a suggested air pressure setting that produces the lowest amount of rolling resistance for the best fuel mileage

Yamaha... | Answered on Oct 25, 2019


The only way it will run backwards is the timing is incorrect. If you had the flywheel or anything in the engine apart relating to the ignition pickup coils, they didnt get put back in correctly.
It's possible something is loose, and sheared the flywheel key. 2 cycle will run regardless of direction due to no valves.

Yamaha... | Answered on Oct 25, 2019


Hi, William all bulbs must be 6-volts, for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Hyosung, despair not, for a mere $20 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?q=6-volt+turn+signal+bulb+1972+Yamaha+LT2+100&source=univ&tbm=shop&tbo=u&sa=X&ved=0ahUKEwjEvf2SnJzlAhXOtVkKHZxWCPUQsxgILw&biw=1440&bih=757
https://www.jpcycles.com/motorcycle-taillight-and-turn-signal-bulbs/6-volt
https://www.repairmanuals.co/products/yamaha-motorcycle-repair-service-manual-choose-your-motorcycle-instant-access?cmp_id=992550392&adg_id=47921554743&kwd=&device=c&gclid=EAIaIQobChMIs9mqr5yc5QIVAeiGCh3zDwbeEAQYAiABEgIC5fD_BwE $20
https://www.partsfish.com/page/oem-parts-for-yamaha
http://mybikemanuals.com/yamaha/

Yamaha... | Answered on Oct 22, 2019

Not finding what you are looking for?
1996 Yamaha FZX 250 Zeal Logo

5 questions posted

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

vince

Level 3 Expert

1234 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1176 Answers

Israel Pineiro Jr

Level 2 Expert

165 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

FZX 250 Zeal Yamaha

  • FZX 250 Zeal Yamaha

Most Popular Question

yamaha timberwolf 250

  • Motorcycles
Loading...