20 Most Recent
2007 TN'G Baja 150 Questions & Answers
I have honda recon 250 it will idel all day but
YOU HAVE A PROBLEM WITH YOUR HEAD, CAUSE BY OVERHEATING IT.....CHECK GASKET FIRST AND THEN WARP HEAD SECOND.IF NOT CONVINCED YET. REBUILT MOTOR THIRD BECAUSE IT GOING TO SET THERE LONG TIME AND COLLECT DUST..
Carb problem
Sounds like a problem with the main jet. Make sure the carb is cleaned of all the gunk from old fuel. Idle jet ok but if throttle opens too much air will kill engine if the main jet is blocked.
Have baja 125 motorsport idels fine but when
ALWAYS have a fire extinguisher at hand when working on carburetors.
Remove the water trap bowl at the bottom of the petcock, (gas valve). Is there any water or trash in the bowl? Drain a cup of gas from the tank. Is there any water or trash in the cup? Dump it, clean it and re-mount it, ( not all bikes have a water trap bowl ).
Drain the carburetor. There may be a screw on the lower side of the carb float bowl. Remove the screw then replace it after the fuel drains. Turn the gas back on and wait a minute for the carb to fill with gas. Install a new stock NGK spark plug and try to start the engine. If the bike doesn't start and run properly then shut off the gas and remove the carburetor from the engine.
Remove the float bowl and clean the entire carb with a spray carb cleaner from the auto parts store. Wear protective goggles to avoid getting spray in your eyes. Spray into all the little airways and fittings in the carb. Remove the idle screw and the air screw on the outside throat of the carb and spray into the screw holes as well.
< < READ CLOSELY > >
Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two adjusters down. Only screw these in until they LIGHTLY seat. Now turn each adjuster one and one half turns outward. Put the rest of the carb back together, clean the air filter and install the carb. Let the float bowl fill then start the engine. This process should get you back on the road.
Please rate this solution. Thanks!
TNG Baja 150 (Ugrading Peformance)?
Hi ..... Any motor vehicle can be made more efficient or faster, what would you like top achieve ? Faster acceleration, top speed or both ? It's usually a compremise. I think the bike you have is a bored out 125 (factory designed 125) so any benefits will be marginal.Top end and accelleration can be achieved by gearing, which is relatively cheap but as mentioned before is one or the other. More expensive mod's would be increasing the bore (bigger piston), skimming the cylinder head (raising compression), flat slide carb and performance exhaust .......... by spending alot of money and time you could have a fast (say 180 cc) that'll be as good as a 250cc bike ................. Let me know if this has been of help and I can/will go into more detail.
Baja dimensions
Length 75 in
Width 23 in
Height 48 in
Seat Height 31.5 in
Dry Weight 250 lbs
Rated Load Capacity 330 lbs
Need circuit diagram for ARLEC 15e 6-24Volt 15Amp Electronic battery charger OR their later model BC58
I can't find a diagram.
The small potentiometer on the control board likely serves as an adjustable component to fine-tune specific parameters. Here are some possibilities:
Voltage Regulation:
The potentiometer might control the output voltage. By adjusting it, you can set the desired charging voltage for different battery types (e.g., 6V or 12V).
Current Limit Adjustment:
It could be used to set the maximum charging current. Adjusting the potentiometer allows you to limit the charging current based on the battery's capacity and condition.
Sensitivity or Threshold:
Some potentiometers act as sensitivity controls. For example, it might adjust the threshold at which the charger switches between charging and maintenance modes.
Setting the Potentiometer:
Without the specific circuit diagram or detailed information about your charger, I recommend the following general steps:
Observe the Potentiometer:
Identify the potentiometer on the control board. Note its position and any markings (if present).
Consult the User Manual:
Check the user manual or operating instructions. It might provide guidance on adjusting the potentiometer.
Trial and Error:
If no specific instructions are available, start with the potentiometer set to its mid-position.
Gradually adjust it while monitoring the charger's behavior (e.g., charging current, voltage).
Observe how the charger responds to changes in the potentiometer setting.
Fine-tune it based on your specific battery type and desired charging characteristics.
Remember that precise adjustments depend on the charger's design and the battery you're charging.
4/18/2024 7:22:52 PM •
Motorcycles
•
Answered
Yesterday
What is the length of lift cables on a 1993 model 2693 hilo camper and any info on what after market part to use ? thanks
The lift cables on a 1993 model 2693 Hilo camper are 30 feet,2 3/4 inches long and fit the standard height lift of 11 feet 8 inches high to the top of the overhead. The lift uses two cables. According to a Hi- Lo camper travel trailer forum, cable replacement is basically the same on all years and models, with the main difference being the length of the cables from model to model. You can use a cable cut chart to find what cable length you need for your camper, and you'll need to know your year, model name, and box (body) length: Lift cables typically wear out after three to five years, so it's important to replace them as needed and keep them regularly maintained.
4/12/2024 1:26:15 AM •
Motorcycles
•
Answered
on Apr 12, 2024
Not finding what you are looking for?