20 Most Recent
2003 Suzuki VL 800 Volusia - Page 8 Questions & Answers
Unable to locate fuse for turn signals and tail
it is in the fuse box on the left side under the tool box. you will see a large wire housing going into a metal box. remove that box from the frame and it is in there. sorry, I do not remember which one it is but it will be the one that is blown. not trying to be a smart ***, but I really dont know the number or if you knew where the box was. good luck
2003 vl800
take off the tank. you will see a breather hose that comes off your air intake up on the right side. under that is the carb. look in next to the air filter and you will see what looks like a large radiator type clamp. get a long flat head screw driver and loosen it. the carb will pull up and lay over on top after it is removed. you can then disconnect the air lines and the rest of the lines to it and it will be free.
I have an rm125 and wen at full revs the bike
If you mean the clutch begins to slip after half revs then chances are that the fiber clutch plates are worn. I suggest you get a set of fiber plates and install. Pull the right engine cover and remove the clutch end cap. Note the sequence of plates as you remove them. You will have fiber plates and steel plates. Is the first plate removed fiber or steel? If the first plate removed is fiber then the next is steel, then fiber, then steel, and so on. Install the new plates in the same fashion. So if you started with a fiber plate you need to end up with a fiber plate when the install is done.
Pleas rate this solution. Thanks!
2003 Suzuki Volusia 800 will not start
I own an 03 volusia and it has a starter button(black) on the right handle bar below the starter kill switch (which is red) .Lots of luck EJ in Georgia
Rattle or clatter under excelleration
It may be your crome covers on your heads. Take your fingers and try to wiggle them . All of these bikes
have some kind of a rattle to them. Most not visible . I have found these covers to be the most often the
problem . You have to tighten just snug . Some times the rubber spacer on the bolts get damaged and
some come up missing.
Runs rough
did it have a K&N before?? or check sealing correct.
Blown fuse
You will need to know exactly what doesn't work, then trace all the circuits and determine the failing wire or component.
Oil filter location
Good idea to replace the gasket on the oil drain if you can. How tight? I get about 1 turn past snug. Filter (oil?) Snug then 3/4 turn. Air? Same.
HOW DO I REPLACE THE RADIATOR ON MY SUSUZI VL800 INTRUDER
Hello i have a question how do i knw where is my radiator water fluid insert and what is the big radiator looking box of my 86 Suzuki Intruder vs700,?? I was traying to remplace my water but it seems like it get oil some how to engine is that BAD RIGHT? cuz idk if the front box radiator looking type is my radiator or oil runner?
I changed my front tire
Hi, it sounds like the wheel is not in the centre of the forks, check the spacers are in the correct location, left and right,
My only problem is I
The horn is behind the radiator, it looks like a small black dome. The horn sometimes stops working when it gets dirty so if that's your problem you may be able to fix it by just reaching in and cleaning the unit.
No idea if Suzuki's are built by hand.
I intended on changing spark
Get a spark plug socket that has a rubber insert to hold the plug when removed or inserted. Go ahead and remove the gas tank but be CERTAIN to mark the hoses as to what goes where. This should allow you to locate the loose wire connection.
Have 2001 Suzuki Volusia, was
That sounds like it is an adjustable lever to be adjusted by the numbers to fit your hand size. Large hands lever farther away from the handlebar. Smaller hands lever set closer to the bars.
Not finding what you are looking for?