Hi, Quick_qwik before testing any electrical component in the Starter Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries. Depending on battery voltage starter relays and starter solenoids can make the same noise when you hit the starter button. You can easily determine which one is at fault by two simple tests:
STARTER RELAY- place your thumb and index finger on the starter relay and press the starter button, if you feel the click then the relay is faulty and needs to be replaced.
STARTER SOLENOID- bridge the positive and negative poles of the solenoid with a small screwdriver if you get a loud clunk then the solenoid needs to be rebuilt or replaced as necessary. If the engine turns over then replace the starter relay.
A motorcycle starter relay is an electronic mechanical switch that has a small coil winding around a piece of metal that requires low amperage and thin wires to be activated. When you turn on your ignition switch power 12 volts is sent to the relay coil which in turn becomes a magnetic contact point that pulls a spring-loaded contact point to itself completing an electrical circuit that allows more amperage necessary to be accessed by the starter solenoid which in turn acts in the same way as the relay but on a larger scale with its stronger heavier contacts making available the necessary amperage to turn the starter motor. If your battery has low voltage it, in turn, makes the magnetic contact point weak in trying to pull its counterpart to make a connection. These relays are usually encased in a plastic housing that is sealed depending on the quality of the product. When activated they will produce a small amount of heat to their metal components which in turn can create the perfect environment for condensation to form depending on weather conditions and how careless you may be with a water hose or sprayer while washing your bike. After a period of time, several months to several years depending on the circumstances this condensation is the starter button for electrolysis and the slow build-up of corrosion which ends by preventing the magnetic contacts in making a solid connection and alerts you to this situation with the customary greeting "CLICK or BUZZ" if you get a single loud "CLUNK" then the starter solenoid is at fault and needs to be rebuilt or replaced as necessary. The relay is inexpensive and needs to be replaced however in a pinch they can be forcibly opened cleaned and resealed with silicone. In a nutshell, motorcycle starter relays take in low amperage and send out higher amperage when activated and for curious minds, the voltage remains constant at whatever your battery reads at the time.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day. Help Bike wont start just clicks Suzuki GSX Motorcycle Forums Gixxer com GSXR 1000 Wont Start Troubleshooting Partzilla com Suzuki 2001 GSX R600 Service Manual https://www.partsfish.com/page/oem-parts-for-suzuki http://mybikemanuals.com/suzuki/suzuki-gsx-owners-manuals
Hi, Rocketcruzer and the usual suspects are:
1. Spark plugs in bad condition or partially fouled.
2. Spark plug cables in bad condition and leaking check for spark leakage in the dark.
3. Spark plug gap too close or too wide.
4. Faulty ignition coil, module, and or sensor.
5. Battery nearly discharged.
6. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
7. Intermittent short circuit due to damaged wire insulation.
8. Dirty air filter
9. Intake air leak.
10. Water, dirt, or rust in the fuel system, fuel pump and/or filter.
11. Old dead or bad fuel.
12. Faulty fuel pressure regulator
13. Pinholes in the in-tank plastic convoluted tubing from the pressure regulator to the quick disconnect check valve.
14. Fuel tank vent system plugged.
15. Throttle body controls misadjusted.
16. Damaged throttle body or intake seals.
17. Clogged or faulty fuel injectors.
18. Loose, dirty, or corroded ignition module connector at crankcase.
19. Faulty TPS, MAP, CKP, O2, and/or CMP sensors.
20. Incorrect valve timing.
21. Weak or broken valve springs.
22. Damaged intake or exhaust valve.
23. The control module may be in limp mode.
24. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day. Misfire issues Suzuki GSX Motorcycle Forums Gixxer comhttps://netrider.net.au/threads/2002-suzuki-gsx-r-600-suddenly-running-rough.112438Suzuki 2001 GSX R600 Service Manualhttps://www.partsfish.com/page/oem-parts-for-yamahahttp://mybikemanuals.com/suzuki/suzuki-gsx-owners-manuals
Hi, Krookedracer if your bike has been sitting idle for months or years and you did not do any pre-storage maintenance I feel your pain it will probably have a dead battery and not want to start or if it starts it will not idle unless the choke is full on and run poorly then stall, here are the following steps necessary to complete in order to get your bike back to an acceptable running condition and in the future pour in a bottle of fuel stabilizer and injector cleaner for you FI folks at least 2 times a year and before storage.
1. If your battery was 2-3 years old when you last had the bike running you should replace it.
2. If you believe your battery might still be serviceable remove it from the bike and put it on a 1 or 2 amp trickle charger for 24 hours. If it is the old lead acid type with visible cells and acid levels fill each cell to the top line with distilled water and replace the caps, run the vent tube into a plastic or styrofoam cup, any cells that are cloudy/milky replace the battery.
3. After charging remove the leads and let the battery sit for a couple of hours then check the battery voltage with a voltmeter, you should have 12.5 volts or more, any readings in the 11 volt range you need to do a proper "LOAD" test on the battery and replace as necessary, you may have 12.5 volts or better but little or zero amps, any readings in the 10 volt range you have a dead cell and the battery needs to be replaced.
4. Drain and flush fuel tank if it rusty there is a cheap and easy fix. https://www.youtube.com/watch?v=fUYr_7SwGms
5. Remove and inspect your air cleaner paper elements that are not oil soaked can be cleaned with a soft brush and low pressure compressed air, oil-soaked elements must be replaced. Gause mesh and foam elements can be cleaned by soaking them in a container big enough to completely cover them with a solution of 1 gallon of water and 1 oz. of Dawn dishwashing liquid for small and medium size elements, for monster size double the formula and let soak for at least one hour then rinse with warm water shake off excess and let air dry, "WARNING" do not use compressed air as this will embed micro-sized dirt and road grime and destroy the mesh pattern and stretch foam elements out of shape just squeeze it like a sponge and let air dry, use a fan if you're in a hurry. When completely dry spray a very fine mist of air filter oil evenly around the whole element.
6. Remove the carburetors, disassemble and decontaminate with a "CARB DIP" or if you have EFI remove injectors and clean with carb spray and compressed air
7. Check intake manifold and seals for leaks and cracks.
8. Remove fuel valve and filter disassemble and clean as necessary, remove, clean, and inspect fuel and vacuum lines and replace as necessary.
9. Replace spark plugs with new ones and check for spark.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day. https://motorcycleviews.com/maintain/psstart01.htm How To Get Stored Motorcycle Running Motorcycle Repair Suzuki 2001 GSX R600 Service Manual https://www.partsfish.com/page/oem-parts-for-suzuki http://mybikemanuals.com/suzuki/suzuki-gsx-owners-manuals
Hi, Anonymous and the usual suspects are:
1. Fuel tank empty.
2. The fuel tank has old dead gas.
3. Fuel tank bottom contaminated with ethanol sludge, dirt, water, rust, etc.
4. Fuel supply valve/petcock turned off.
5. Fouled spark plugs.
6. Engine flooded as a result of overuse of the choke.
7. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
8. Fuel valve/petcock or filter clogged.
9. Fuel line to carburetor or throttle body pinched, kinked or blocked.
10. Carburetor float stuck.
11. Fuel injectors clogged.
12. Fuel injectors stuck open.
13. Quick disconnect check ball stuck.
14. Compression below 75 PSI.
15. A stuck-bent-burnt valve.
16. Improper valve clearance (too tight)
17. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a cursory reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
18. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
19. Loose or corroded wire connection at the coil or plug between ignition sensor and ECM module.
20. Spark plug cables in bad condition and shorting check for spark leakage in the dark, cable connections are loose or connected to the wrong cylinders.
21. Ignition timing incorrect due to a faulty ignition coil, ignition module or MAP, CMP, CKP, O2, TPS, ETP, IAC sensors.
22. Faulty neutral, clutch, kickstand safety switch.
23. Faulty fuel pump or fuse or relay.
24. Faulty or corroded run/stop switch.
25. Tilt sensor needs a reset.
26. Security system not disarming alarm needs a reset.
27. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day. 2001 gsxR Will Not Start Suzuki GSX Motorcycle Forums Gixxer com GSXR 1000 Wont Start Troubleshooting Partzilla com Suzuki 2001 GSX R600 Service Manual https://www.partsfish.com/page/oem-parts-for-suzuki http://mybikemanuals.com/suzuki/suzuki-gsx-owners-manuals
Hi, Anonymous if your headlight is not working, intermittent, only one beam works, keeps burning out, blinking, dim or surges from bright to dim to bright the first thing you need to check is the headlight bulb for damaged filaments then check your light circuit fuse, then check your headlight bulb socket ground wire for a clean tight connection, that being said the usual suspects are:
1. Faulty ground or power supply wire to headlight bulb socket.
2. Worn down solder contacts or loose fit of the bulb base in the socket due to vibration.
3. Worn, chafed, or broken wires in the light circuit.
4. Corroded, broken, or loose pins/sockets in wire connectors.
5. Faulty hi/low beam switch.
6. Faulty ignition switch.
7. Fuse is good but no continuity on both sides.
8. Faulty headlight relay.
9. Faulty wiring between battery positive and headlight bulb socket.
10. Weak charging alternator/generator/lighting coil
11. Faulty voltage regulator/rectifier ground or overcharging.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day. Headlight won work GSXR comGSXR Headlight not workingSuzuki 2001 GSX R600 Service Manualhttps://www.partsfish.com/page/oem-parts-for-suzukihttp://mybikemanuals.com/suzuki/suzuki-gsx-owners-manuals
Hi, Samuel and the usual suspects are:
1. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
2. Failed alternator/generator and or voltage regulator.
3. Loose or corroded battery terminals and or cables especially the "NEGATIVE" cable, look for loose, corroded, or broken connectors inside the cable harness at "BOTH" ends.
4. Failed main circuit breaker or ignition switch, check for loose connections and continuity.
5. Failed system and or ignition relay, check for continuity.
6. Failed ignition coil, stator, magneto, ignition/electronic module.
7. Failed CKP, CPS, CMP, MAP, TPS, or BAS sensor, corroded, loose or broken wire connector pins/sockets.
8. Throttle cables and or idle speed improperly adjusted hot idle speed should be 950 RPM to 1000 RPM.
9. Faulty neutral, side stand or clutch lever safety switch.
10. Faulty or corroded kill switch.
11. Accelerator pump damaged or not working.
12. Water or dirt in the fuel system, carburetor or filter.
13. Restricted, blocked or kinked fuel line.
14. Fuel tank empty.
15. The gas cap is not venting properly or fuel tank venting system blocked, loosen gas cap and go for a test ride.
16. A failed fuel pump, pressure regulator and or fuel injectors.
17. Vacuum line from intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
18. Needle and seat stuck closed in the float bowl.
19. Petcock clogged or damaged.
20. Lean angle switch is faulty or needs adjustment.
21. Catastrophic engine failure, perform a compression test.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day. Bike shuts off while riding Suzuki GSX Motorcycle Forums Gixxer com bike cut off while riding Suzuki GSX R600 Service Manual https://www.partsfish.com/page/oem-parts-for-suzuki Suzuki GSX R600 2003 Owner Manual http://mybikemanuals.com/suzuki
The stator is probably it..I had the same problem...After you change it the bike will run so much better. That's why it ran good with the new battery...Then it started draining it..It takes a special tool to get it out..
Not too sure about this but there are a couple of things to try. Fairly sure the fuel pump runs from a relay somewhere in the tangled mass we call a wiring harness. You will also have a dedicated fuse for the pump, the fuse is obviously OK. I would look for the relay and or check the ECU. Do the plugs spark? Sorry can't be more helpful.