20 Most Recent 1988 Suzuki GSX 400 XS Impulse Questions & Answers


Hi, Christianels for more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Suzuki 1980 GSX400 Service Manual
https://www.partsfish.com/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki
https://www.motorcyclespecs.co.za/model/suzu/suzuki_gsx400X%20impulse%2086.htm
https://en.wikipedia.org/wiki/Suzuki_GSX-R400

1988 Suzuki GSX... | Answered on May 15, 2019


Hi, Anonymous and the usual suspects are:
1. Fuel tank empty.
2. The fuel tank has old dead gas.
3. Fuel tank bottom contaminated with ethanol sludge, dirt, water, rust, etc.
4. Fuel supply valve/petcock turned off.
5. Fouled spark plugs.
6. Engine flooded as a result of overuse of the choke.
7. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
8. Fuel valve/petcock or filter clogged.
9. Fuel line to carburetor or throttle body pinched, kinked or blocked.
10. Carburetor float stuck.
11. Fuel injectors clogged.
12. Fuel injectors stuck open.
13. Quick disconnect check ball stuck.
14. Compression below 75 PSI.
15. A stuck-bent-burnt valve.
16. Improper valve clearance (too tight)
17. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a cursory reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
18. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
19. Loose or corroded wire connection at the coil or plug between ignition sensor and ECM module.
20. Spark plug cables in bad condition and shorting check for spark leakage in the dark, cable connections are loose or connected to the wrong cylinders.
21. Ignition timing incorrect due to a faulty ignition coil, ignition module or MAP, CMP, CKP, O2, TPS, ETP, IAC sensors.
22. Faulty neutral, clutch, kickstand safety switch.
23. Faulty fuel pump or fuse or relay.
24. Faulty or corroded run/stop switch.
25. Tilt sensor needs a reset.
26. Security system not disarming alarm needs a reset.
27. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
turns over but wont start Suzuki GSX Motorcycle Forums Gixxer com
What To Do If Your Motorcycle Doesn Start
Suzuki 1980 GSX400 Service Manual
https://www.partsfish.com/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki

1988 Suzuki GSX... | Answered on Apr 28, 2019


Hi, Andrew the ignition circuit cut-off system comprising of the side stand switch, clutch switch and neutral switch has the following functions:
a. It prevents starting when the transmission is in gear and the side stand is up, but the clutch lever is not pulled.
b. It prevents starting when the transmission is in gear and the clutch lever is pulled, but the side stand is still down.
c. It cuts the running engine when the transmission is in gear and the side stand is moved down.
Periodically check the operation of the ignition circuit cut-off system according to the following tests.
With the engine turned off:
1. Move the side stand down.
2. Make sure that the engine stop switch is set to "RUN"
3. Turn the key to "ON".
4. Shift the transmission into the neutral position.
5. Push the start switch if the engine does not start the neutral switch may be faulty.
With the engine still running:
6. Move the side stand up.
7. Keep the clutch lever pulled.
8. Shift the transmission into gear.
9. Move the side stand down if the engine does not stall you may have a faulty side stand switch.
After the engine has stalled:
10. Move the side stand up.
11. Keep the clutch lever pulled.
12. Push the start switch if the engine does not start you may have a faulty clutch switch.
This check is most reliable if performed with a warmed-up engine.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.gixxer.com/forums/15-oil-cooled-gixxers/647394-side-stand-switch.html
How kickstand switch causes no start situation
Suzuki GSX 400F Service Manual
https://www.partsfish.com/page/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki

1988 Suzuki GSX... | Answered on Apr 07, 2019


Hi, Anonymous the answer to this question is way above my pay grade for this situation, I would call or visit my local dealer or reputable shop's service/parts department and inquire about any possible quick fix, answers, or parts inquiry.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.google.com/search?q=1985+Suzuki+GSX+400+GK71B+carburetor&source=univ&tbm=shop&tbo=u&sa=X&ved=0ahUKEwj79pSsxejgAhWGrVkKHafbCrAQsxgIjgE&biw=1440&bih=757
https://www.ebay.co.uk/itm/SUZUKI-GSX-R-400-GK71B-1984-1985-Keihin-Carburettor-Carb-2-Main-Body-V379FA08-/232945642097
https://www.tradebit.com/filedetail.php/275699893-suzuki-gs-gsx-250-400-450-1979-1985 $15
https://www.partsfish.com/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki

1988 Suzuki GSX... | Answered on Mar 04, 2019


Hi, Alan for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Suzuki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Parts Specifications SUZUKI GSX 400 Louis Motorcycle Leisure
DRZ 400E Fork oil change
Suzuki GSX 400F Service Manual
https://www.partsfish.com/page/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki

1988 Suzuki GSX... | Answered on Sep 12, 2018


Hi, Sturmtiger the answer to these questions are way above my pay grade for this situation, I would call or visit my local dealer or reputable shop's service/parts department and inquire about any possible quick fix, answers, or parts inquiry.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Suzuki GSX 400F Service Manual
OEM parts for Suzuki
http://mybikemanuals.com/suzuki
Suzuki GSX 400 1984
Suzuki GSX series

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1988 Suzuki GSX... | Answered on Jul 02, 2017


It sounds like you have a bad vacuum leak. Check the carb mounting bols to make sure they are tight. Check all of the vacuum hoses for cracks and leaks. If this doesn't turn anything up, you can check for leaks around the carb mounting points by spraying carb cleaner around the base of the carb (If you spray the leak, the engine RPM will go crazy. - this can work on hoses that are hard to get to also)

1988 Suzuki GSX... | Answered on May 19, 2014


Replace the clutch cable. Replace, or recharge and test, the battery, it should have about 12.5 volts when fully charged. Then you will most likely need to remove and clean the carbs. Use care in cleaning the jets, do not make the holes any bigger just get the crud out.

1988 Suzuki GSX... | Answered on Mar 29, 2010


Hi ...................... NGK recommend NGK CR7E.

1988 Suzuki GSX... | Answered on Dec 23, 2008


153 kg (337.3 pounds)

1988 Suzuki GSX... | Answered on Nov 20, 2008


Hi, Andy the vast majority of service, parts fiche, and owners manuals on the internet are "FREE" to download and all service manuals contain wiring diagrams in the back pages. The rest usually charge a modest fee of $15 and there is a handful of obscure, rare, obsolete, and very old models that are no longer or never were available and some were never printed in English. The Indian and Philippine markets are usually in E-book format only, for these rare occasions I shall look on eBay and find the cheapest one available. Most of the manuals will cover your exact make, model, and year otherwise one will be provided that comes as close as possible to your bike and will have most of the same info that an exact manual would have. If there is no $ sign after the manual link it is free to download.
To download your manual for viewing or printing please click on the blue links below. Good luck and have a wonderful day
Suzuki GSXR400 GSX R400 1984 1987 Repair Service Manual PDF Download... $15
https://www.partsfish.com/page/oem-parts-for-yamaha
http://mybikemanuals.com/suzuki/suzuki-gsx-owners-manuals
Suzuki GSX R400
https://en.wikipedia.org/wiki/Suzuki_GSX-R400

Suzuki GSX 400... | Answered on Nov 03, 2018


Depends what your question is.

Suzuki... | Answered on Jul 13, 2019


Hi, Edward for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kymco, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.gixxer.com/forums/15-oil-cooled-gixxers/193810-92-1100-wierd-clutch-disengage-problem.html
https://www.gsxr.com/13-tech-performance-chat/26967-1992-gsxr-1100-clutch-problem.html
https://www.partsfish.com/page/oem-parts-for-suzuki
https://motodataproject.com/suzuki-manuals/1986-1988-suzuki-gsx-r1100-service-manual
http://mybikemanuals.com/suzuki

Suzuki... | Answered on Jul 09, 2019


Approx-85mph.

Suzuki... | Answered on Jul 08, 2019


Hi, Kim and the usual suspects are:
1. Fuel tank empty.
2. The fuel tank has old dead gas.
3. Fuel tank bottom contaminated with ethanol sludge, dirt, water, rust, etc.
4. Fuel supply valve/petcock turned off.
5. Fouled spark plugs.
6. Engine flooded as a result of overuse of the choke.
7. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
8. Fuel valve/petcock or filter clogged.
9. Fuel line to carburetor or throttle body pinched, kinked or blocked.
10. Carburetor float stuck.
11. Fuel injectors clogged.
12. Fuel injectors stuck open.
13. Quick disconnect check ball stuck.
14. Compression below 75 PSI.
15. A stuck-bent-burnt valve.
16. Improper valve clearance (too tight)
17. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a cursory reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
18. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
19. Loose or corroded wire connection at the coil or plug between ignition sensor and ECM module.
20. Spark plug cables in bad condition and shorting check for spark leakage in the dark, cable connections are loose or connected to the wrong cylinders.
21. Ignition timing incorrect due to a faulty ignition coil, ignition module or MAP, CMP, CKP, O2, TPS, ETP, IAC sensors.
22. Faulty neutral, clutch, kickstand safety switch.
23. Faulty fuel pump or fuse or relay.
24. Faulty or corroded run/stop switch.
25. Tilt sensor needs a reset.
26. Security system not disarming alarm needs a reset.
27. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.motorcycleforum.com/59-motorcycle-repair/88604-suzuki-ts-185-wont-start.html
What To Do If Your Motorcycle Doesn Start
https://www.oldjapanesebikes.com/mraxl_GT_Resource/manuals/gt185man/index.php
https://www.partsfish.com/page/oem-parts-for-suzuki
http://mybikemanuals.com/suzuki

Suzuki... | Answered on Jul 08, 2019


Worngasket ir loose bolts..go ovr bike for othr maintenanc..rmembr ur doin sixti on twowheels

Suzuki... | Answered on Jul 03, 2019


Hi, Anonymous and the usual suspects are:
1. Fouled spark plugs.
2. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
3. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Loose connection at ignition coil or plug between ignition sensor and module.
5. Spark plug cables in bad condition, shorting/leaking, spark plug cable connections loose check for spark leakage in the dark.
6. A faulty ignition coil or electronic control module.
7. Faulty pulse coil.
8. Faulty CKP, CMP, or BAS sensor.
9. Faulty ignition switch.
10. Faulty run/off switch
11. Tilt sensor needs a reset.
12. Security alarm failing to disarm needs reset
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://ohioriders.net/index.php?/topic/18498-no-spark-on-old-suzuki
http://www.chopcult.com/forum/showthread.php?t=31896
https://onedrive.live.com/?authkey=!APM7hx6Q2ynLu-A&cid=2370B62DDF9F0C6B&id=2370B62DDF9F0C6B!1334&parId=2370B62DDF9F0C6B!1276&o=OneUp
https://www.partsfish.com/page/oem-parts-for-suzuki
http://gsarchive.bwringer.com/mtsac/~cliff/storage/gs/GS450GA_Owners_Manual.pdf

Suzuki... | Answered on Jun 29, 2019

Not finding what you are looking for?
1988 Suzuki GSX 400 XS Impulse Logo

Popular Tags

14 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Suzuki Experts

Marvin
Marvin

Level 3 Expert

85111 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

5914 Answers

richard libby

Level 2 Expert

208 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

GSX 400 XS Impulse Suzuki

  • GSX 400 XS Impulse Suzuki

Most Popular Question

fast bike go from 0 100 kph or

  • Motorcycles
Loading...