20 Most Recent 2008 KTM 990 Adventure Questions & Answers

Ive never worked on them, but, i havent really heard anything negative from them.

I have the same problem and same model (2008 KTM Adventure 990 S) so injection, not carburator.
I didn't start the engine for three months. I bought a brand new battery. Lights, fuel pump and everything seemed to be ok at the first key turn. But when you try to turn it even more to definitely start the engine, ignition fails. I think the electric engine of the starter is not working properly.
I tried to start the engine driving down the slope and releasing the clutch in 2nd gear at aprox 30 km/h and it started successfully.
I left it idle until became hot (15 min aprox) and the turned it off.
however it didn't start again when trying the ignition button.
Any ideas?

piston rings gone or valve seals gone to check for this get a compression tester and screw into the place off the spark plug and kick the bike over till the readings on the guage go no higher and tell me the readings off the psi get back to me buddy

That would be like riding a fixed wheel bike.Think about how you will stop and start. Only hydraulic fluid will leak. Bad idea!

Question edited for clarity. That sounds like it is just a bad connection somewhere or possibly a bad switch. Remove the battery leads and clean the lead contacts and battery posts with a wire brush. Smear with Vaseline and reconnect. Remove the starter leads and do the same. Then it could be the Starter Relay https://www.google.com/search?q=ktm+450+sx-f+starter+relay+location Or Starter Button https://www.google.com/search?q=ktm+450+sx-f+starter+button+replacement ..

personnaly I would replace cylinder with new OEM

All dirt bikes have a VIN. It is on the steering neck. https://www.google.com/search?q=vin+on+my+ktm+300 ..

Have you checked battery connections. Run switch in the correct position? Checked spark plug for debris? Just thinking out loud..

Drain oil. Use degreaser to clean area. Use JB Weld & allow to set up properly before adding oil.

If you’ve found this helpful, please click the green “helpful” icon. If you have 20 seconds please leave a few words as a review or recommendation! Also, follow me for more answers to everyday issues, I’m all for saving you money and making the most of your time! Thanks and have a great day!

Hi, try to see this link and looking for the manual that you need. https://www.pdfmotomanual.com/manuales/ktm/eng I hope to give you an help. Luca

my ­b­est ­fr­i­e­n­d's s­ist­er-­i­n-­l­Aw ­m­A­k­es $74 ­ev­ery ­h­our ­o­n t­h­e ­c­o­m­put­er. S­h­e ­h­As ­b­e­e­n u­n­e­m­p­l­oy­e­d ­f­or t­e­n ­m­o­nt­hs ­but ­l­Ast ­m­o­nt­h ­h­er ­p­Ay­m­e­nt w­As $16505 just w­or­k­i­n­g ­o­n t­h­e ­c­o­m­put­er ­f­or ­A ­f­ew ­h­ours. ­g­o t­o t­h­is w­e­b s­it­e ­A­n­d r­e­A­d ­m­or­e ­g­o t­o t­h­is s­it­e ­h­o­m­e t­A­b ­f­or ­m­or­e ­d­et­A­i­l ... www.online-3.com

Hi, most likely your cdi unit or ignition coil needs replacing.

took me a min or two of WTF-ing to see pic and realize you meant a 2-stroke motorcycle..

try replace spark plugs

It's a bad seal of the head gasket. You need a new head gasket and to scrape every particle of debris from the cylinder head and cylinder surfaces that mate with the head gasket. Use the factory specified gasket sealing compound and do a clean job - no blobs or pools of the stuff. The head gasket should lay flat on the surface of the top of the cylinder, and you have to make this surface free of grit, leftover sealant and any other foreign matter before you put the head in place and torque it down. Start with the head bolts just finger tight and then go by the manufacturer's specs for the pattern and amount of torque to be applied. Usually it is recommended that you get to the specified torque amount in stages, going around several times and repeating the torque pattern until you get that maximum rated amount. This will prevent the seal from shifting or warping and should make the gasket seal perfectly. This is the old school method of doing this job. and I have never seen this fail to produce good results. Take your time, be clean, and you will have the results you want.

Check the clutch, adjust, clean, or replace

over full sump fuel getting into sump badly worn rings allowing excessive blow by

Worn out shift dogs.

Make sure cables are working . Follow it down to clutch and make sure clutch lever is actually moving. It is does then pull clutch in and pushbike backwards. Should release If not , plates are probably frozen through excessive heat. Replace them. If lever does not move when clutch handle pulled, then adjust or broken cable. hope that' it, easier and cheaper!