20 Most Recent 2005 kawasaki ZX-10R Questions & Answers

your fuel sensor is faulty needs to be replaced

Is a Meta Alarm to prevent theft? ... Seems it is working. If it is your machine - put it back on. If it is someone else's machine ... well, maybe you should return it to the owner and tell them you are sorry.

hi there has this fuel pump been sitting for a while dry if it has it could have seized this up put some fuel in the out end of the pump and see what happens let it soak and check that there is power to it ,even if it has had fuel in them it can be that the fuel has left a sticky brown gunge in the pump which you may be able to wash out ,if not it could mean a new pump as i have had the same problems with other fuel pumps ,cheers pete

the converter is inside the pipe and cant see the case from the outside like a car. can only see by removing pipe from header and looking in the header

Yes this is quite a time consuming job you will have to remove the seat, fuel tank, air box ,left and righthand fairings, no 2

good day Sir, try this link i hope this will help you

kawasaki

what kind of light is it? warnning light

Check that your fuel is getting through properly ,you may have a blocked jet .

the tool kit with the bike should be good enough,no need to lower the engine, to make things easier when you get them undone find a piece of rubber hose that fits over the sparkplug and use it to pull the plugs out and install them ...then tighten them with the plug tool.

BUDDY TRY THIS SITE WWW.TASTYNUTS.CO.UK

did ypu change the plugs yourself

Have you looked in the manual??
http://www.carlsalter.com/download.asp?fileid=075097119097115097107105095090088049048082095078105110106097095050048048052095083101114118105099101095077097110117097108046112100102

Good luck.

Hi there!

make sure your carburetors are clean. I guess you've done that already. I had this problem once and i drained the carburetor fuel reservoir and found out that it had water mixed in it. Pull on the chock and ram the throttle several times to get rid of any water stuck on the jets. Also, clean the plugs, and let the chamber dry for a while like 30 minutes... replace the spark plugs.

let me know if this helps
-levibit

if it is a zx10r 05 model there is a rear plastic cover that is directly behind the rear passengers seat which also wraps around both sides of the bike to meet both side covers ,on the left hand side of the rear cover there is a key barrel that unlocks the rear seat ,but the key is barrel hidden and can only be seen by looking underneath and the key is inserted with the main plastic (black handle)bit facing toward the ground and the metal part of the key will be pointing towards the sky ,so you will have to sit on the ground to see it and look or feel under to find it and when you do it will remove rear seat so when you turn the key lift up on the front of the rear seat to remove it then you will see that the front seat is held down by a bolt .

Kawasaki calls for 576 +-4ml of fork oil. You can change the height to change the damping of the forks (less oil = softer, more oil = harder) The front suspension is a 43mm Inverted Cartridge Fork with Adjustable. Click on the link below to view the complete specifications for the 2006 Kawasaki ZX10 motorcycle:

http://www.bikez.com/motorcycles/kawasaki_ninja_zx-10_r_2006.php

Try asking a place I know that does <a href="http://www.brakecheck.ca/Services.aspx">brake repair in Calgary</a> I am sure they can help you out.

what problems u have with it?..i can give you a link where you can get the service manual for it, it will help a lot check below link:http://goo.gl/W6Gdgngood luck

What about it?

This is maybe a 15 minute job. The dealership will charge you probably an hour for labor and a hefty markup on the oil and filter. It's not only faster than having to take it somewhere, you will also save probably close to $100 every time it needs a change.Drain plug is way down on the bottom of the engine. It's easy to over torque when you're putting it back on so use a torque wrench and tighten to 22 ft-lb. Assuming you change the filter you'll need 3.9 quarts of 10W-40 oil. I never take the plastic off and I just hand tighten the filter from below. If you want to torque the filter on (13 ft-lb) you'll need the left fairing off. If this is the first change the filter will be black and you can access it from underneath the bike on the left side. Lay on the floor and reach right between the headers and the engine.I also recommend you follow these steps: (1) drain the old oil, (2) fill the new oil until you can see it in the sight glass (3) remove the old filter (4) pour new oil into the filter to soak it (5) install the new filter (6) start up and let it run for a couple minutes (7) shut off and add oil as necessary until the level is in the middle of the sight glass.BMW ACCESSORIES.

Its mounted next to the battery positive cable. You can see a picture of this if you go to:

http://www.seekinsoul.com/component/content/category/44?layout=blog

(3rd picture on the page)