20 Most Recent 1999 kawasaki ZX-6R Ninja Questions & Answers


Hi, Orlando and the usual suspects are:
1. Engine oil system overfilled.
2. Piston rings worn past service specs.
3. Broken piston rings.
4. Piston pin retaining clip failure.
5. Cracked piston.
6. Broken piston ring lands.
7. Hole in the piston.
8. Valve/guide clearance worn past service specs.
9. Worn out valve seals.
10. Crushed or loose valve seal.
11. Gouges in cylinder walls.
12. Cracked cylinder or head.
13. Blown head gasket.
14. Crankcase breather blocked or hose pinched.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
white smoke from exaust ZX6R Forum
Oil Gas Spitting Out Of The Exhaust Sportbikes net
Kawasaki Ninja ZX 6R Service Manual
OEM Parts for Kawasaki
Kawasaki Ninja ZX 6R Owner Manual

1999 kawasaki... | Answered on Aug 20, 2018


Hi, Anonymous engine "BOG" is mainly caused by a rich air and lean fuel condition but it can also be caused by a lean air and rich fuel condition this situation rarely occurs and is only caused by the misinformed weekend warrior that owns a toolbox. If the bike has been sitting for months or years you will have to completely disassemble the carburetor and submerge the parts (except rubber parts) in "Carburetor Dip" It usually comes in a gallon bucket with a wire mesh basket that can be purchased at any automotive store. If it is not the above scenario then the following explanation will apply.
The more you open your throttle the more vacuum you are creating in your carburetor venturi and your intake manifold. When you are operating at higher RPM any unmetered air that leaks into your system can become more obvious.
Unmetered air is air that is getting into your system after the fuel has been delivered. If you have unmetered air getting into your system between the butterfly/slide of the carburetor and the cylinder head this will create a lean condition.
All of the rubber components of the fuel system like vacuum hoses and intake manifold that you mount the carburetor to are made of rubber. If none of these components have been changed they are more than likely highly degraded and probably cracked in places to allow unwanted-unmetered-contaminated air into the combustion chamber. Check all of your vacuum lines and vacuum plugs for carburetor synchronization. The vacuum plugs are in the head just after the rubber intake manifolds. The petcock has a vacuum line as well as part of the emission system.
1. Check the intake manifold for fissures.
2. Ensure the bands used to tighten the manifolds down on the intake are secure and have not bound up the manifold.
3. Make sure air box fittings are not warped and fit completely over the carburetor.
Your airbox is metering air and is the first step in a process of consuming air and fuel. The system requires the resistance of the air filter in order to get the proper vacuum to "SUCK" the fuel out of the float bowl and create the proper venturi effect.
Improper mounting and sealing of the airbox will create a small lean effect. This might seem like no big deal but you are inviting dust and debris in your engine that is doing slow damage by not having proper fitment. Fix it so you know it's not contributing to your issue. Pick the low-hanging fruit first.
Do not go and start adjusting anything at this point. It ran fine before. There is something wrong with the assembly or a component. Do not adjust your floats. Get it back to where it was. The moment you start tweaking everything is the moment you lose OEM settings which are a must-have for fine-tuning and maximum performance.
Fine-tuning your carburetor and multi carb syncing come at the very end following the proper procedure established by the Carburetor Gods.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Losing power top speed is 70 at 9 000rpm WHAT GOING ON ninjette org
https://www.bikechatforums.com/viewtopic.php?t=258596 Kawasaki Ninja ZX 6R Service Manual
OEM Parts for Kawasaki
Kawasaki Ninja ZX 6R Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1999 kawasaki... | Answered on Apr 10, 2018


Hi, Cmartin_200 for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Timing Chain Replacement on the Kawasaki ZX 6R FourWheelForum
2005 Kawasaki ZX 6R Timing Chain Overview
http://zx6r.com/service-manuals/12589-1998-1999-kawasaki-zx-6r-service-manual.html
OEM Parts for Kawasaki

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


1999 kawasaki... | Answered on Mar 25, 2018


Hi, James_k400 for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere $15 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Suspension Setup Guide ZX6R Forum
Suspension Settings KawiForums Kawasaki Motorcycle Forums
1998 1999 Kawasaki Ninja ZX 6R ZX600 Service Repair Factory Manual INSTANT... $15
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1999 kawasaki... | Answered on Mar 25, 2018


Hi, Mandysummers for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere $15 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
How to Change Brake Pads on Kawasaki Ninja
How to Change Motorcycle Brake Pads ZX6R
Kawasaki Ninja ZX 6R 1995 2002 Service Repair Factory Manual Download... $15
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


1999 kawasaki... | Answered on Mar 24, 2018


Hi, Don and the usual suspects are:
1. Low coolant level.
2. Restricted radiator air flow.
3. Faulty thermostat.
4. Coolant pump or fans inoperative.
5. Vent hose crimped.
6. Air in the coolant and needs bleeding.
7. Engine idling too long or bike moving too slow.
8. Coolant too old needs to be replaced.
9. Faulty temperature sensor, wiring or connector.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://zx6r.com/zx6r/47981-1998-zx6r-running-hot.html
Possible reasons for overheating KawiForums Kawasaki Motorcycle Forums
Kawasaki Ninja ZX 6R 1995 2002 Service Repair Factory Manual Download... $15
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1999 kawasaki... | Answered on Mar 24, 2018


Hi, Dobbie669 try using a single lip fork seal, for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere $15 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Motorcycle Fork Rechroming Service for Stanchions Both Legs
Getting fork tubes re coated
Kawasaki Ninja ZX 6R 1995 2002 Service Repair Factory Manual Download... $15
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1999 kawasaki... | Answered on Mar 24, 2018


Hi, C_adi86 for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere $15 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
ZX 6R Maintenance Service Spark Plugs
urgent changing spark plugs now ZX6R Forum
Kawasaki Ninja ZX 6R 1995 2002 Service Repair Factory Manual Download... $15
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1999 kawasaki... | Answered on Mar 24, 2018


Hi, Pamcgeown for more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Sprocket setup ZX6R Forum
https://motorcyclesofdulles.com/vortex-performance-links-chain-sprocket-kits-detail.htm?productId=18268235
Kawasaki Ninja ZX 6R 1995 2002 Service Repair Factory Manual Download... $15
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1999 kawasaki... | Answered on Mar 24, 2018


Hi, Mooncat1970 before diagnosing your blown fuse issue, check the bottom of your seat, if its metal and comes in close proximity to the positive battery post you need to take the necessary steps to ensure there is no contact (electrical tape, thick rubber insulation, hammer a dent in the seat bottom etc.) You are going to need a wiring diagram from your service manual, a test light, an ohmmeter and plenty of extra fuses.
If you turn on your ignition switch and immediately blow a fuse you have a hard/dead short and is usually easy to find. With a test light connected to the hot side of the blown fuse holder start stabbing the wire/s that leads away from the fuse holder and towards the ignition switch, you test light will illuminate validating the short. When the test light fails to illuminate you have passed the short and need to back up until the test light illuminates, then look in the immediate area for the short.
If you driving down the road for 30 minutes or 15 miles and blow a fuse you have soft/flying short and may take some time and patience to find.
If the main fuse/circuit breaker constantly blows/trips while riding you probably have a faulty battery terminal connection. Check battery terminals for damage or corrosion, check battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary. Any other fuses that constantly keep blowing while riding are usually caused by a loose or corroded ground wire in the circuit, which means you have to check, inspect, test each and everyone with an ohm meter set on a low ohm scale 100 ohms or less . Simply touch one lead to the ground source and the other lead to the battery negative terminal, a reading of zero indicates a clean solid ground. Any number reading or infinity indicates a poor ground and needs to be repaired. Poor or weak grounds require excessive additional amperage to complete the circuit which in turn blows the small amperage fuse.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Electrical Main 30A Fuse Keeps Popping ZX Forums
Ignition and Main ECU fuses keep blowing
Kawasaki Ninja ZX 6R 1995 2002 Service Repair Factory Manual Download... $15
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1999 kawasaki... | Answered on Mar 23, 2018


Hi, Amyl_woods82 and the usual suspects are:
1. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
2. Failed alternator/generator and or voltage regulator.
3. Loose or corroded battery terminals and or cables especially the "NEGATIVE" cable, look for loose, corroded, or broken connectors inside the cable harness at "BOTH" ends.
4. Failed main circuit breaker or ignition switch, check for loose connections and continuity.
5. Failed system and or ignition relay, check for continuity.
6. Failed ignition coil, stator, magneto, ignition/electronic module.
7. Failed CKP, CPS, CMP, MAP, TPS, or BAS sensor, corroded, loose or broken wire connector pins/sockets.
8. Throttle cables and or idle speed improperly adjusted hot idle speed should be 950 RPM to 1000 RPM.
9. Faulty neutral, side stand or clutch lever safety switch.
10. Faulty or corroded kill switch.
11. Accelerator pump damaged or not working.
12. Water or dirt in the fuel system, carburetor or filter.
13. Restricted, blocked or kinked fuel line.
14. Fuel tank empty.
15. The gas cap is not venting properly or fuel tank venting system blocked, loosen gas cap and go for a test ride.
16. A failed fuel pump, pressure regulator and or fuel injectors.
17. Vacuum line from intake manifold to petcock broken, cracked, or not attached, carburetor vent line plugged.
18. Needle and seat stuck closed in the float bowl.
19. Petcock clogged or damaged.
20. Lean angle switch is faulty or needs adjustment.
21. Catastrophic engine failure, perform a compression test.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://zx6r.com/zx6r/43882-2003-zx6r-dies-stalls-when-rpm-drops.html
Losing power bogging on Freeway High RPM Scary Help Please Kawasaki Ninja ZX 6R 1995 2002 Service Repair Factory Manual Download... $15
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1999 kawasaki... | Answered on Mar 23, 2018


Hi, Stephen and the usual suspects are:
1. Neutral light bulb burnt out.
2. Faulty neutral switch.
3. A loose bulb in the socket.
4. Faulty wiring from the neutral switch to the light.
5. If the neutral light stays on while the bike is in gear the wire from the light to the neutral switch is grounded.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Neutral Light Gear Sensor Engine Strip
Neutral light stays on
Kawasaki Ninja ZX 6R 1995 2002 Service Repair Factory Manual Download... $15
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1999 kawasaki... | Answered on Mar 23, 2018


Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere $15 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Parts Specifications KAWASAKI ZX 6R NINJA Louis Moto
Changing the Oil Filter of Motorcycle Kawasaki Ninja 636 ZX6R
Kawasaki Ninja ZX 6R 1995 2002 Service Repair Factory Manual Download... $15
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


1999 kawasaki... | Answered on Mar 23, 2018


Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere $15 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Kawasaki Motorcycle Paint ColorRite
http://zx6r.com/zx6r/3096-kawasaki-zx6r-g1-color-codes.html Kawasaki Ninja ZX 6R 1995 2002 Service Repair Factory Manual Download... $15
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1999 kawasaki... | Answered on Mar 22, 2018


Hi, Dave and the usual suspects are:
1. Faulty wiring to any safety switch.
2. Safety switches loose at the mounting point.
3. Faulty kickstand safety switch.
4. Failed kickstand safety switch circuit diode.
5. Stretched side stand spring.
6. Side stand not coming up far enough to disengage switch.
7. Faulty clutch lever safety switch.
8. Faulty neutral safety switch.
9. Clutch not properly adjusted.
10. Clutch plates sticking, forward lurch
For more information about your question and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
ninja will idle but dies when try to put it in gear KawiForums Kawasaki...
zx6r 05 when put in gear engine stalls
Kawasaki Ninja ZX 6R 1995 2002 Service Repair Factory Manual Download... $15
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1999 kawasaki... | Answered on Mar 22, 2018


Hi, Anonymous it should be noted that the "AIR FUEL" mixture screw adjustment "ONLY" manages your idle and has no effect on any other circuit also any intake leaks must be repaired before the A/F adjustment procedure can be performed otherwise you will never obtain a proper idle and you will waste a lot of time chasing the impossible. The A/F mixture screw's purpose is to fine tune the fuel charge entering the combustion chamber. The following applies to both 2 and 4 stroke engines:
1. The mixture screw may be sealed at the factory with a Welch Plug please review the following video for removal.
https://www.youtube.com/watch?v=wAXcksgvDkM
2. The mixture screw manages a range of 3 complete 360-degree counterclockwise turns from the bottom/closed position.
3. The mixture screw should have a spring and o-ring for tension and sealing integrity.
4. Turn the mixture screw clockwise until it gently bottoms out, this makes the fuel charge very lean and the engine should not idle if it does then the pilot/idle jet is too big and needs to be replaced with the next size smaller.
5. Turn the mixture screw 1 and 1/2 turns counterclockwise to establish a baseline for starting the engine.
6. To fine-tune the idle circuit, adjust the mixture screw 1/4 turn in or out to achieve maximum idle RPM, wait 15 seconds between each adjustment for the idle to settle.
7. Never go past 3 full turns out this will make the fuel charge rich, foul plugs, and produce black smoke out of the exhaust, if the engine RPM keeps increasing past 3 turns the pilot/idle jet is too small and needs to be replaced with the next size larger.
8. After achieving maximum idle back out the mixture screw another 1/8 of a turn then adjust the throttle cable idle stop screw to 950-1050 RPM.
9. This procedure works great on 99% of all engines, for the 1% that demand a more robust throttle response on aftermarket monster fuel delivery systems additional tweaking outside the box may be necessary.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://www.zxforums.com/forums/mechanical-technical/37527-setting-mixture-screws.html
http://zx6r.com/zx6r/4617-trying-tune-2000-zx-6r.html
Kawasaki Ninja ZX 6R 1995 2002 Service Repair Factory Manual Download... $15
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


1999 kawasaki... | Answered on Mar 22, 2018


Hi, Jeff for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere $15 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
How to test motorcycle pickup coils
HOW TO TEST AND GAP PICK UP PULSAR COIL
Kawasaki Ninja ZX 6R 1995 2002 Service Repair Factory Manual Download... $15
OEM Parts for Kawasaki
Kawasaki Ninja Owners Manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e



1999 kawasaki... | Answered on Mar 22, 2018


Hi, Jeff for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
1999 Kawasaki ZX 6R Ninja relay quantity Google Search
Motorcycle Electrical Ignition Relays for Kawasaki Ninja ZX7 eBay
Kawasaki Ninja ZX 6R Service Manual
OEM Parts for Kawasaki
Kawasaki Ninja ZX 6R Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1999 kawasaki... | Answered on Jan 19, 2018


Check for vacuum leaks around the carb. intake boots. If there are no leaks take carbs apart and clean the main and intermediate jets. you may have to possibly rejet it with different size jets. Have you made any changes to the bike's engine or exhaust?

1999 kawasaki... | Answered on Jan 15, 2018


My first check would be the battery to earth connection...... High resistance is a real no-no - strip, clean, re-attach to frame.

1999 kawasaki... | Answered on Nov 02, 2017

Not finding what you are looking for?
1999 kawasaki ZX-6R Ninja Logo

Popular Tags

119 questions posted

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5944 Answers

Marvin
Marvin

Level 3 Expert

85178 Answers

ROB

Level 3 Expert

858 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

ZX-6R Ninja kawasaki

  • ZX-6R Ninja kawasaki

Most Popular Question

bought bike sitting up

  • Motorcycles
Loading...