20 Most Recent
1987 Honda NSR 250 MC 16 Questions & Answers
Should the power valve honda nsr 250 cycle every time I turn the ignition on@
No, the power valve on a Honda NSR 250 should not cycle every time you turn the ignition. The power valve is typically actuated by engine RPM and throttle position, adjusting exhaust port timing for optimal performance. It may move during engine operation but not necessarily during every ignition cycle, depending on operating conditions. You can buy new model bikes there are many new option available but first calculate your earnings stats on check here.
CDI box on my nsr
check with the local mechanic if you can get a second hand product in working condition....
Can i get a manuel
http://the-manuals.com/repair-manual-for-1985-honda-atc-250-sx-manual/ try this might help some if not look for a haynes manual is the bible for all bikers who do there own work
Is there a trick to kick starting my nsr 250??
I stand on the left hand side of my bike and lean over the seat.
I then use my hand to start my MC 16. Every one thinks it is funny but my legs are too long and the kick stater is too short. I hope this is what you meant.
J.D snowmobile 340 73 carb wont idle appears internally clean.
I would have your compression tested, if its a two stroke, and you can use tools with out breaking things or yourself, pour a cup of fuel down the left hand side of the carb and take the right hand side of the carb off and crank it like mad, if fuel leaks from there you better get to a repairer.
other wise the idle adjuster is usually on the left hand side where the accelerator linkages are, it will be a screw where the linkage touches when the throttle is closed. not too hard to find if you have a light source.
Hope this helps.
If you want any more help just ask :)
Honda 500 TRX fa6 has PS on the dash….what does it mean ?
The Power Steering has failed. There has been a factory recall for a suddenly failing electrical steering shaft, that could cause the rider to loose control. This does not have to be your problem but anyhow either the electronics or the pump failed. Error codes or messages usually have to be erased by a simple reset procedure or disconnecting a plug, after repairs are done.
3/31/2024 4:25:47 AM •
Honda...
•
Answered
on Mar 31, 2024
Hiss works but
On the bottom of your speedometer on the left side there is 2 buttons
press the far left one for a couple of seconds and the light should go on
1/8/2024 6:42:24 AM •
Honda...
•
Answered
on Jan 08, 2024
What to torque the head on my 99 CBR 929 Honda in
For a 1999 Honda CBR929RR, the cylinder head bolt torque specifications are essential to ensure proper engine assembly and function. When tightening the cylinder head bolts, it's crucial to follow the manufacturer's recommended torque settings to prevent damage to the engine components.
For the CBR929RR, the cylinder head bolt torque specifications are typically as follows:
1. **Initial Torque:** 29 Nm (2.9 kgf-m, 22 ft-lbs)
2. **Final Torque:** 64 Nm (6.4 kgf-m, 47 ft-lbs)
It's essential to tighten the cylinder head bolts in the specified sequence and in multiple stages, gradually increasing the torque until reaching the final specified torque. The exact tightening sequence can usually be found in the service manual specific to your motorcycle model.
When torquing the head bolts, ensure you're using a reliable torque wrench calibrated in the appropriate units (Nm or ft-lbs). Always follow the tightening sequence precisely to ensure even pressure distribution across the cylinder head gasket.
Additionally, it's advisable to use new cylinder head bolts if the old ones have been previously tightened or stretched beyond their yield point. This helps maintain proper clamping force and ensures the integrity of the engine assembly.
As always, referring to the service manual or consulting a professional mechanic experienced with motorcycle engine assembly can provide additional guidance and ensure the correct torque settings are applied during the cylinder head installation process.
12/10/2023 4:27:33 AM •
Honda...
•
Answered
on Dec 10, 2023
2006 Honda Shadow Arrow 750 VT missing on the rear cylinder fire
. One possibility is that the spark plug or plug wire is faulty 1. Another possibility is that the carburetor needs cleaning and adjustment It could also be due to a valve adjustment issue or a bent rod.
I would recommend taking your motorcycle to a professional mechanic who can diagnose and fix the issue. If you prefer to troubleshoot it yourself, you can start by checking the spark plug and plug wire for any damage or wear and cleaning the carburetor. However, please note that working on a motorcycle engine can be dangerous and requires specialized knowledge and tools. Please take all necessary safety precautions and follow the manufacturer's instructions when working on your motorcycle.
10/22/2023 2:01:22 PM •
Honda...
•
Answered
on Oct 22, 2023
Not finding what you are looking for?