20 Most Recent
1989 kawasaki ZX 10 Questions & Answers
1989 Kawasaki ZX 10 clutch lever master cylinder jams up
...??.. the bore that the plunger rides in may be worn to the point of allowing it to bind... its a wear related thing..your bike/master cylinder IS 28 YEARS old...
Do a full master cylinder rebuild..if it does not fix it.. think about a NEW master cylinder..(a used one is NOT ok)..
Storage of motor cycles
in regards to storing a bike that might be sitting idle for a long period of time . You should remove the spark plugs and put a small amount of engine oil in each cylinder about a tea spoon of oil in each would do the trick as this will prevent the piston rings binding to the cylinder walls due to any rust build up and then replace the spark plugs, flushing out any extra fuel in the carbs and fuel line should also be done and perhaps some DW40 sprayed into the line and carbs as a protector for rubber parts etc , the fuel from your tank should be removed and some sort of rust protection sprayed into it (WD40 ) .If the bike is stored outside condensation can build up under plastic covers so spraying exposed parts like the front forks around the rear suspension and many nuts and bolts with WD40 will help , also a good waxing over the whole bike is helpful , remove the battery and try to keep the tiers off the ground or at least slip something under them so water will not perish the rubber , block the exhaust pipe so water can not enter but condensation can escape ( a tin can that fits over the muffler opening ) and i suggest that you move the bike by pushing it a few feet back and forth every 2 months to prevent any parts from locking up . one more final thought lock the bike up very secure making it difficult to be stolen as a parked bike sitting for a long time can attract criminals !
Kawasaki zx10 1989 has been standing for 10 years.
There could be other things involved.
- Have you checked the tank and the fuel valve for crud. It should have a screen on the valve and it may have crud or rust stopping it up.
- The tank valve will have to be removed from the tank to check the screen.
- Have you checked the valve settings - clearance..
- Spark plugs.
- Spark plug wires and spark.
- Compression, does she have good compression?
- Timing?
1987 kawasaki ninja zx10 wont stay running when warmed up it
you didnt mention anything to do with the carbs so try some "Sea foam".... purchase at Autozone ($10) pour 1/3 can to two gallons fuel and drive it around for a good 10 to 15 miles and get on it once in awhile, ride safe..if the carbs are dirty or clogged... they wont be after your ride..there might be a little hesitation your first couple of miles till it starts to work..it took my bike 10 miles before it cleared out..bump start your bike if you have to to get it going and keep it going till it clears up.
How do i get a 180 tyre to fit my zx10 1989
you need zzr1100/d rear wheel and all spacers,get whole wheel if poss. you also need rear shock from d or c zzr1100. this will bring bike back to ride hight. play with spacers and away you go, makes it little bit nippy.
My zx10b keeps stopping after riding a few miles
Drain the carburetors. There should be a screw on the lower side of each carb float bowl. Remove the screw then replace it after the fuel drains. Any water in the gas? Remove the water trap bowl at the bottom of the petcock, (gas valve). Any water or trash in the bowl? Drain a cup of gas from the tank. Any water or trash in the cup? Dump it, clean it and re-mount it, ( not all bikes have a water trap bowl ). Turn the gas back on and wait a minute for the carbs to fill with gas. Install a new stock NGK spark plugs and try to start the engine. If the bike doesn't start and run properly then shut off the gas and remove the carburetors from the engine.
FOR EACH CARB > Remove the float bowl and clean the entire carb with a spray carb cleaner from the auto parts store. Wear protective goggles to avoid getting spray in your eyes. Spray all the little airways and fittings in the carb. Remove the two screws on the outside throat of the carb and spray into the screw holes as well.
< < READ CLOSELY > >
Be sure to put these two screws back in the same hole they came out of. IMPORTANT > do not tighten these two screws down. Only screw these in until they LIGHTLY seat. Now turn each screw one and one half turns outward. Put the rest of the carb back together, clean the air filter and install the carb. Let the float bowl fill then start the engine. This process should get you back on the road.
Please rate this solution. Thanks!
Clutch is slipping
contact the person you got it from there may be a warrenty on the recently installed clutch !! you must make sure there is no leeks or problems with the clutch master cyclinder
Hi , what is the
The stock battery is Yuasa brand, YB14L-A2. Be sure to keep the water level in the battery above the top of the plates in each cell. Also, check the voltage across the battery terminals while the bike engine is running around 2500rpm. The voltmeter should read around 14.5 volts. If it reads 15 or higher the voltage regulator is probably bad. Please take a moment to rate my answer. Thanks!
I have an 89 ZX10
You still have an obstruction in one or more carb. Start it cold and start feeling for a cold exhaust pipe. (That will be the bad cylinder) Be careful as they get hot very fast.
Hi where is the fuse
take side fairings off. remove two bolts on seat one on each side. fuse box under sea
Remove seat ZX10?
take the side fairings off and there are two bolts you'll need to back out. one bolt on each side
I'm riding a 1989 zx10.
hi..
use this -->Universal Yana Shiki 1 Litre of Bel-Ray ..20W fork oil..
it gives best performance..
If it's useful for you means plz rate me the 4 Thumbs ....
Hello have a 1989
hi, have you tried draining the old fuel from the carbs, undo the drain screw in each float bowl untill all the fuel is removed retighten and try to start again, may need carb overall, poss choke jets in carbs blockage
paul
Not finding what you are looking for?
