20 Most Recent 1987 kawasaki VN 750 Vulcan Questions & Answers


Hi, Davea7207 wires that get hot or melting are usually caused by a faulty ground and or positive connection.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.vn750.com/forum/19-electrical/1423-stator-wire-connectors-melting.html
Stator wires HOT and also REGULATOR SUPERHOT Steve Saunders Goldwing Forums
Kawasaki VN 750 Service Manual
OEM Parts for Kawasaki
http://mybikemanuals.com/kawasaki

1987 kawasaki VN... | Answered on May 15, 2019


Hi, Colin and the usual suspects are:
1. Spark plugs in bad condition or have an improper gap or are partially fouled.
2. Spark plug cables in bad condition.
3. Battery damaged or nearly discharged, should have 12.5 volts.
4. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
5. Throttle controls not adjusted correctly.
6. Water or dirt in the fuel system.
7. Water or dirt in the carburetor.
8. Intake air leak.
9. Fuel tank vent hose and vapor valve plugged, or fuel line closed off, restricting fuel flow.
10. Choke valve inoperative.
11. Engine lubricant to heavy (winter operation).
12. Ignition is not functioning properly (possible sensor failure).
13. Faulty ignition coil.
14. Valves sticking.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
1985 700 starting problems Kawasaki Vulcan 750 Forum Kawasaki VN750 Forums
Kawasaki Vulcan 750 Troubleshooting Guide
Kawasaki VN 750 Service Manual
OEM Parts for Kawasaki
http://mybikemanuals.com/kawasaki/kawasaki-vulcan-owners-manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1987 kawasaki VN... | Answered on Jun 17, 2018


Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Choke cable Kawasaki Vulcan 750 Forum Kawasaki VN750 Forums
How to Replace Manifold How to Remove Choke Cable on Motorcycle
Kawasaki VN 750 Service Manual
OEM Parts for Kawasaki
1989 Kawasaki Vulcan 750 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


1987 kawasaki VN... | Answered on Mar 17, 2018


Hi, Roeearsley for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Timing information Kawasaki Vulcan 750 Forum Kawasaki VN750 Forums
Vn750 DIY mcct adjustment
Kawasaki VN 750 Service Manual
OEM Parts for Kawasaki
1989 Kawasaki Vulcan 750 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


1987 kawasaki VN... | Answered on Mar 16, 2018


Hi, Jon_b_c for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
rear tire Kawasaki Vulcan 750 Forum Kawasaki VN750 Forums
How to remove the rear wheel of your shaft driven motorcycle
Kawasaki VN 750 Service Manual
OEM Parts for Kawasaki
1989 Kawasaki Vulcan 750 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


1987 kawasaki VN... | Answered on Mar 15, 2018


Hi, D1602 and the usual suspects are:
1. Clutch not adjusted properly.
2. Primary chaincase overfilled with lubricant.
3. Corners wore off shifter clutch dogs.
4. Shifter return spring bent or broken.
5. Bent shifter rod.
6. A loose shift lever on shifter shaft.
7. Shifter forks sprung.
8. Shifter pawl needs adjusting.
9. Heel/toe shifter coming in contact with the floorboard.
10. Transmission oil too heavy.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Shifting Gears Kawasaki Vulcan 750 Forum Kawasaki VN750 Forums
http://www.kawasakimotorcycle.org/forum/mechanics-corner/128592-2004-vulcan-750-cant-shift-into-2nd-gear.html
Kawasaki VN 750 Service Manual
OEM Parts for Kawasaki
1989 Kawasaki Vulcan 750 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1987 kawasaki VN... | Answered on Mar 15, 2018


Hi, Tlcrawford35 if you are experiencing excessive oil coming out of the crankcase breather or air filter please drain all engine oil and replace half of the same oil that comes out. Many riders are overfilling their oil system because they do not know how to properly read their oil site glass or dipstick. The following procedure works on nearly all 4 stroke engines but to be on the safe side you should refer to your owners manual. Use your center stand if you have one.
1. Bring the engine up to operating temperature or let idle for 5 minutes.
2. Turn off your engine and let it sit for 2 minutes, this will allow the oil from the top end to drain to the bottom.
3. Hold your bike straight up or on the center stand and wait 2 minutes for the oil in the bottom of the engine to be level in the sight glass or on the dipstick.
4. Your oil level should be between the top full mark and the bottom add oil mark.
5. Never overfill your oil system it will cause problems:
a. oil leaking out of exhaust pipes.
b. oil leaking out of breather pipe/hose.
c. oil carryover into the air cleaner.
6. Your oil site glass must "NEVER" be completely full or empty drain or add oil as necessary.
7. Your oil dipstick must "NEVER" be over the full mark and should never be below the add mark drain or add oil as needed.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Check oil level
Checking oil level Kawasaki Vulcan Forum Vulcan Forums
Kawasaki VN 750 Service Manual
OEM Parts for Kawasaki
1989 Kawasaki Vulcan 750 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1987 kawasaki VN... | Answered on Mar 15, 2018


Hi, Matt for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
1986 Kawasaki VN750 Vulcan fuel and vacuum line routing Google Search
Carb vent line route Kawasaki Vulcan 750 Forum Kawasaki VN750 Forums
Kawasaki VN 750 Service Manual
OEM Parts for Kawasaki
1989 Kawasaki Vulcan 750 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1987 kawasaki VN... | Answered on Mar 15, 2018


Hi, Tomwalsh286 before testing any electrical component in the Starting Circuit it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries.
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Engine Run Switch is "FAULTY" or corroded.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
5. Bank angle sensor needs a reset or is faulty.
6. FOB battery low or dead.
7. Faulty ignition switch.
8. Faulty starter button.
9. Faulty kickstand, clutch, neutral safety switch.
10. Security alarm needs a reset.
11. Starter relay, solenoid, starter motor or circuit wiring faulty.
12. Starter armature or field coils have failed.
13. Main fuse or circuit breaker may be blown or faulty.
14. Faulty ignition relay.
15. The electric starter is working but starter clutch has failed.
16. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
bike won turn over anymore Kawasaki Vulcan 750 Forum Kawasaki VN750 Forums
Kawasaki Vulcan 750 Troubleshooting Guide
Kawasaki VN 750 Service Manual
OEM Parts for Kawasaki
1989 Kawasaki Vulcan 750 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1987 kawasaki VN... | Answered on Mar 14, 2018


Hi, Anonymous for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Oil Change Procedure Kawasaki Vulcan 750 Forum Kawasaki VN750 Forums
How to change motorcycle oil Kawasaki Vulcan
Kawasaki VN 750 Service Manual
OEM Parts for Kawasaki
1989 Kawasaki Vulcan 750 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


1987 kawasaki VN... | Answered on Mar 14, 2018


Hi, Tony for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://www.vn750.com/forum/47-maintenance/1162-spark-plugs-wires.html
Kawasaki Vulcan 1500 Specs Kawasaki Vulcan 750 Parts
Kawasaki VN 750 Service Manual
OEM Parts for Kawasaki
1989 Kawasaki Vulcan 750 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1987 kawasaki VN... | Answered on Mar 14, 2018


Hi, Anonymous and the usual suspects are:
1. Fouled spark plug.
2. Fuel injector stuck open.
3. Carburetor float needle valve, not seating.
4. Carburetor float stuck open.
5. Exhaust valve stuck open.
6. Exhaust valve bent.
7. Fuel valve leaking back through the vacuum line.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
fuel leaking out my exhaust Kawasaki Vulcan 750 Forum Kawasaki VN750 Forums
Raw Gas Coming Out Exhaust Kawasaki Vulcan Forum Vulcan Forums
Kawasaki VN 750 Service Manual
OEM Parts for Kawasaki
1989 Kawasaki Vulcan 750 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1987 kawasaki VN... | Answered on Mar 14, 2018


Hi, Anonymous the vast majority of service, parts fiche, and owners manuals on the internet are "FREE" to download and all service manuals contain wiring diagrams in the back pages. The rest usually charge a modest fee of $15 and there is a handful of obscure, rare, obsolete, and very old models that are no longer or never were available and some were never printed in English. The Indian and Philippine markets are usually in E-book format only, for these rare occasions I shall look on eBay and find the cheapest one available. Most of the manuals will cover your exact make, model, and year otherwise one will be provided that comes as close as possible to your bike and will have most of the same info that an exact manual would have. If there is no $ sign after the manual link it is free to download.
To download your manual for viewing or printing please click on the blue links below. Good luck and have a wonderful day
Kawasaki VN 750 Service Manual
OEM Parts for Kawasaki
1989 Kawasaki Vulcan 750 Owner Manual
Kawasaki VN 750 Vulcan
https://en.wikipedia.org/wiki/Kawasaki_Vulcan_750

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1987 kawasaki VN... | Answered on Mar 13, 2018


Hi, Jeff_dot2000 for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Motorcycle Shocks for Kawasaki Vulcan 750 eBay
Rear Shock oil change
Kawasaki VN 750 Service Manual
OEM Parts for Kawasaki
1989 Kawasaki Vulcan 750 Owner Manual

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1987 kawasaki VN... | Answered on Nov 23, 2017


Hi, Tyler for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere zero $ you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
1985 kawasaki vulcan 700 wiring diagram Google Search
Kawasaki Motorcycle Wiring Diagrams
Kawasaki VN 750 Service Manual " Free"
KAWASAKI VULCAN VN700 VN750 TWIN BIKE WORKSHOP MANUAL Download Manuals... $16
OEM Parts for Kawasaki
http://mybikemanuals.com/kawasaki/kawasaki-vulcan-owners-manuals

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1987 kawasaki VN... | Answered on Feb 28, 2017


Hi, Gary for this situation I would call my local dealer or reputable shop's service/parts department and inquire about any possible quick fix, answers, or parts inquiry. If necessary, transport your bike to the dealer or shop and have a professional technician take it for a test drive, if it is in running condition, and give you a written estimate of repairs and answer any specific questions you may have about your issue. For more information about your issue please visit the website below. Good luck and have a nice day.
1st cylinder fills up with gas anyone Suzuki GSX Motorcycle Forums Gixxer...
Cylinders Filled Gas Kawasaki ATV Forum carb issues overflow excessive fuel Kawasaki Vulcan Forum Vulcan Forums

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

1987 kawasaki VN... | Answered on Dec 12, 2015


Hi John:
One possible could be a bad connection or broken wires at the fitting. That would increase resistance which would result in a temperature increase.
I'd make sure the connection was clean and secure, and that the wire was intact before looking further.

1987 kawasaki VN... | Answered on Aug 18, 2015


Yes, It is the same type system used on most cars, trucks and other motorcycles. All wiring is basically the same except wiring color codes.

1987 kawasaki VN... | Answered on Mar 21, 2014


my kawasaki vn 900 is making a chattering sound when I try starting it

1987 kawasaki VN... | Answered on Mar 20, 2014


Definetly a fuel level issue in float chamber,

1987 kawasaki VN... | Answered on Mar 14, 2014

Not finding what you are looking for?
1987 kawasaki VN 750 Vulcan Logo

35 questions posted

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5944 Answers

Marvin
Marvin

Level 3 Expert

85178 Answers

ROB

Level 3 Expert

858 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

VN 750 Vulcan kawasaki

  • VN 750 Vulcan kawasaki

Most Popular Question

hazard lights

  • Motorcycles
Loading...