20 Most Recent 1983 kawasaki KZ 1300 A5 - Page 4 Questions & Answers


have some one do the work

kawasaki... | Answered on Dec 09, 2018


Motor oil turns white/beige when it becomes emulsified with water or coolant. While the presence of emulsion can indicate an internal coolant leak or careless topping up the oil level, the nature of modern anti-pollution positive crankcase breather systems draws cool damp air into the hot engine. Some such systems aren't well designed and are prone to creating "mayonnaise", especially in the cooler, damper months.

kawasaki... | Answered on Dec 06, 2018


most likely the crankcase breather valve is not working properly.

kawasaki... | Answered on Nov 23, 2018


One simple way to put the correct amount of oil in the forks is >>>with the fork caps removed and the spacers and fork springs removed from the forks, compress the fork all the down, then fill it 6 inches from the top. You can use a turkey baster (marked and measured) to remove the un-wanted oil if you overfill it.

kawasaki... | Answered on Nov 11, 2018


google it or see a dealer to order one

kawasaki... | Answered on Nov 01, 2018


A variety of possible issues here. Bad plugs dirty carbs or timing chain is stretched and timing is off.

kawasaki... | Answered on Nov 01, 2018


Hi, Scott_towers for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Suzuki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
KX60 Questions
Kawasaki KX60 rebuild part 1
Kawasaki KX60 Service Manual
OEM Parts for Kawasaki
Kawasaki KX65 Owner Manual

kawasaki... | Answered on Oct 29, 2018


Hi, Anonymous before testing any electrical component in the Charging System it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries.
1. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
2. To check the regulator unplug it from the stator. Take a test light and clip it to the negative terminal of the battery and then touch first one pin and then the other on the plug that goes to the regulator. If you get even the slightest amount of light from the test light the regulator is toast.
To do this with a meter: black lead to battery ground, red lead to each pin on the plug, start with the voltage scale higher than 12vdc and move voltage scale down in steps for each pin. Any voltage is a bad regulator.
3. On the other part of the disconnected regulator plug. Set the multimeter for Ohms x1 scale and measure for resistance across the pins of the stator. You should read something around 0.1 to 0.2 ohms for a 32 amp system.
4. Then check for continuity between each pin on the plug and frame/engine ground. The meter needle should not move (infinite resistance)(digitals will show infinite resistance) if the meter needle does move (indicating continuity)(digitals will show some resistance), recheck very carefully. If the meter still shows continuity to ground the stator is shorted (bad).
5. Set the meter to read A/C volts higher than 30 volts (the scale setting for voltage should always be higher than the highest voltage you expect or you may fry the meter). Start the bike, and measure from one pin to the other on the plug (DO NOT cross the multimeter probes! - touch them to each other). You should read roughly 16-20 vac per 1,000 rpm.
6. If the battery was good under load test, if the stator is NOT shorted to ground, and the stator is putting out A/C voltage, then the regulator is bad (most likely even if passed step 2)
For more information about your question and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
HELP Kawasaki Fury Starter Switch and Horn problem
How to diagnose and repair motorcycle charging problems
Kawasaki fury 125 manual pdf
2010 Kawasaki FURY 125 FURY 125R AX125AAF OEM Parts http://mybikemanuals.com/kawasaki

kawasaki... | Answered on Oct 28, 2018


Kawasaki Engine Rebuild Kit ' Dennis Kirk


https://www.denniskirk.com > Kawasaki > Engine Rebuild Kit
  1. Cached

Results 1 - 39 of 39 - Shop the best selection of Kawasaki Engine Rebuild Kit at Dennis Kirk for the lowest prices. FREE SHIPPING on orders over $89 - We Ship ...

Kawasaki Bottom End Rebuild Kit ' Dennis Kirk


https://www.denniskirk.com > Kawasaki > Bottom End Rebuild Kit
  1. Cached

Results 1 - 14 of 14 - Shop the best selection of Kawasaki Bottom End Rebuild Kit at Dennis Kirk for ... Hot Rods Heavy-Duty Crankshaft Bottom End Kit - CBK0178.

1985 Kawasaki KL600 Parts - Best OEM Parts Diagram for 1985 ...


https://www.bikebandit.com/oem-parts/1985-kawasaki-kl600/o/m142669
  1. Cached

BikeBandit.com offers thousands of 1985 Kawasaki KL600 OEM parts to repair or restore your 1985 Kawasaki KL600 to original factory condition. Navigate your ... engine rebuild kit for 1985 Kawasaki kl600b Google Search

kawasaki... | Answered on Oct 28, 2018


You can't its linked to the ECU and will not allow unless you replace ignition and ECU.

kawasaki... | Answered on Oct 22, 2018


You can't, it's linked to the ECU, get replacement keys or new ignition system, which may need a new ECU to match it.

kawasaki... | Answered on Oct 22, 2018


Hi, Jan for more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
2018 Kawasaki Z300 lowering kit Google Search
Putting Lowering Kit on the Ninja 300
Raevyn300 Installs NEW Lowering Kit Roaring Toyz
How To Install Roaring Toyz Lowering Links
Kawasaki Ninja 300 Service Manual
OEM Parts for Kawasaki
Kawasaki Ninja 300 ABS Owner Manual


kawasaki... | Answered on Oct 22, 2018

Not finding what you are looking for?
1983 kawasaki KZ 1300 A5 Logo

4 questions posted

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5884 Answers

Marvin
Marvin

Level 3 Expert

85020 Answers

richard libby

Level 2 Expert

208 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

KZ 1300 A5 kawasaki

  • KZ 1300 A5 kawasaki

Most Popular Question

need wiring diagram or workshopmanual

  • Motorcycles
Loading...