20 Most Recent
1975 kawasaki Mach III H 1F Questions & Answers
Ican only get a very weak spark on all plugs not
Check the security of the coils to the body, remove the coils and sand down the parts where the coil and body contact each other, dab with grease once they're shiny and re-bolt the coil(s) to the body. Also check the connection of the condenser (near the distributor) and all the wiring to and from coils, distributor and battery and check all the HT leads, if the leads are quite old it's a good idea to replace them anyway they're only cheap.
Tell me how you get on, will advise further if this doesn't fix it
I have spent almost an
You haven't told us the exact model of your carburetor so i'll give you several.
A very similar one
http://www.mxsouth.com/keihin/keihin-complete-carburetors-diagram-parts-list-of-pwk33_1.jpg
How to adjust it
http://www.mbraonline.com/uploads/Carburetor_Adjustmentpdf.pdf
A carb for a 250 2-stroke motor from a MX bike
http://www.sudco.com/Diagrams123/expfcrmx.gif
An older 4-stroke Honda CB250K0
http://images.cmsnl.com/img/partslists/carburetor-keihin-cb250k0-france_bigma000102e19_112e.gif
Overheeting
What type of Kawi? I would start with the coolant level if its water cooled and make sure its fresh fluid and not old and burnt. Second if it has a thermostat make sure its functioning properly with no blockage of fluid and water pump is circulating the coolant, and lastly and the most severe the head gasket could be seeping causing the coolant to be compressed with combustion chamber gasses and not allowing the coolant to flow (to verify, make sure your not getting coolant in your oil or out the exhaust as this would be symptoms if this is happening if your loosing coolant)
I have a 2002 Kawasaki Mean Streak 1500 I'm customizing it can the rectifier be moved so it's not just hanging there.
Absolutely, the rectifier on your Kawasaki Mean Streak 1500 can be repositioned during a customization project. The rectifier is a crucial part of the motorcycle's electrical system, converting alternating current (AC) from the stator into direct current (DC) to charge the battery and power the bike's electrical components.
While relocating the rectifier, it's important to consider a few key factors:
- Space and Mounting: Assess the available space on the motorcycle to find a suitable location for the rectifier. Ensure that the new position allows for proper mounting and secure attachment without interfering with other components or the bike's functionality.
- Heat Dissipation: The rectifier generates heat during operation, so it's essential to relocate it to an area with adequate airflow for cooling. Mounting it in a well-ventilated area helps prevent overheating issues.
- Wiring and Connections: When moving the rectifier, ensure that the wiring can be appropriately rerouted to reach its new location. Take care to maintain proper electrical connections and ensure a secure, stable wiring setup.
- Protection: Consider adding protective measures, such as shields or guards, to safeguard the relocated rectifier from road debris, water, or other potential hazards.
Modifying the placement of the rectifier may require custom brackets, mounts, or fabrication work to secure it in the desired location. It's crucial to execute the relocation carefully, maintaining proper electrical connections and ensuring the rectifier's safety and functionality.
If you're not confident in performing these modifications yourself, consulting a professional motorcycle mechanic or technician with experience in customizations can be highly beneficial. They can offer guidance, expertise, and ensure that the modifications are carried out safely and effectively.
12/23/2023 9:33:25 PM •
kawasaki...
•
Answered
on Dec 23, 2023
I have a 2002 Kawasaki Mean Streak 1500 can't find the fuse for the break light can anyone help
I'm assuming you have already checked the actual bulb is still OK? The bike uses a 'twin element' bulb so the tail light element might still work but the brake light element has blown. It's designed to be two bulbs in one so it takes up less space.On a lot of vehicles some electrical features share a fuse and only some of them are marked on the fuse box lid. Has anything else stopped working? On some Kawasaki bikes the brake light shares a fuse with the horn and the tail light so if the fuse has blown all three won't be working. Check the fuse labelled as the Horn to see if that has 'Popped'.*NOTE* ONLY replace fuses with one of the SAME Amp rating as lower 'A' fuses will blow and higher 'A' fuses won't protect your electrics.Bulbs and fuses are usually cheap to buy so you could replace them anyway before thinking it's going to be a 'Big' repair.
3/27/2023 12:12:08 PM •
kawasaki...
•
Answered
on Mar 27, 2023
I have a zzr 600 zzr kawasaki and all at once it quit firing could you please help?
If your Kawasaki ZZR600 suddenly stopped firing, there are several possible reasons for this. Here are some troubleshooting steps you can take to identify and resolve the issue:
- Check the battery: A weak or dead battery can prevent the engine from starting. Make sure the battery is fully charged and has a voltage of at least 12.5 volts.
- Check the spark plugs: The spark plugs may be fouled, worn out, or damaged. Remove the spark plugs and inspect them for signs of wear or damage. If necessary, replace the spark plugs.
- Check the ignition system: The ignition coils, ignition module, and wiring may be faulty. Use a multimeter to test the resistance of the coils and check the wiring for continuity. Replace any faulty components as needed.
- Check the fuel system: The fuel filter may be clogged, the fuel pump may be faulty, or there may be a problem with the fuel injectors. Check the fuel pressure and flow, and inspect the fuel filter and injectors for any signs of clogging or damage.
- Check the carburetor (if applicable): If your ZZR600 has a carburetor, it may be dirty or clogged. Remove the carburetor and clean it thoroughly with carburetor cleaner.
- Check the camshaft timing: If the camshaft timing is off, the engine may not fire properly. Check the timing marks and adjust the camshaft if necessary.
If none of these steps resolve the issue, you may need to take your ZZR600 to a qualified mechanic for further diagnosis and repair.
2/24/2023 9:57:12 PM •
kawasaki...
•
Answered
on Feb 24, 2023
2000 kawasaki kdx 220r engie oil is coming out of a over flow hose on the carb when running
There could be several reasons why oil is coming out of the overflow hose on your Kawasaki KDX 220R. Some possible causes include:
- Overfilled oil tank: If the oil tank is overfilled, oil can get forced out of the overflow hose when the engine is running.
- Worn or damaged oil seals: If the oil seals in the engine or transmission are worn or damaged, oil can leak out of the engine and into the carburetor, where it can then be forced out of the overflow hose.
- Clogged or damaged oil cooler: If the oil cooler is clogged or damaged, it can cause excess oil to build up in the engine, which can then be forced out of the overflow hose.
It's important to identify and address the cause of the oil leak as soon as possible, as running the engine with excessive oil can cause serious damage. I recommend taking your bike to a mechanic for a thorough inspection and repair.
1/9/2023 4:00:04 PM •
kawasaki...
•
Answered
on Jan 09, 2023
Not finding what you are looking for?