20 Most Recent 1971 kawasaki Mach III H 1B Questions & Answers

try a compression test, I guess you have tried swapping spark plugs, and the leads on 2\3 are correct, the cx regulator shouldnt matter

Best I can do is a 1976 KH250. Go to the site below where you can see a parts diagram for this 1976 bike. You will select the actual brand, year, model, etc., once you go to the site. Part numbers and prices are also shown. You can order parts from this site. In the event no price is shown on a particular part, the part is not in stock. For a full size image go to the Babbit's site. www.babbittsonline.com/pages/parts/viewbybrandand/parts.aspx

A “very helpful” rating for this answer? Thanks!

Hi,
In a 2 ring configuration, the compression ring is the top ring, and the expander is the bottom. In the manual, the order of disassembly of the rings, the compression ring is removed off the top first, then the expander.
Hope this helps

This is a common problem with Kawasaki's, all mine do that so I always leave it in neutral.
While still in gear with your clutch pulled in, rock your bike back and forth. If that doesn't work, sit on the bike and with both feet down and off the stands. Leave it in gear and hold the clutch in and push the bike backwards, with your feet. It is easier to push backwards than it is to do the ruptured duck and drag it forward.

If that fails, stay on it keep it in gear and with clutch in. As you push it backward let the clutch out, sometimes this will "break" the locked plates.

First check to make sure the fuel line to the carb is not pinched or obstructed in any way. If the lines are clean the float may be stuck holding the needle closed. Try tapping the bowl with the handle of a screwdriver. Usually it well become unstuck and let fuel flow into the bowl.

It could be the float chamber on the carb/s not sealing off with the petrol valve and filling up the air inlet and then draining down to the crank case.

It is is firing out of the carb and the exhaust, the timing must be off, but also slipping. Is the flywheel tight? https://www.google.com/search?q=1984+kawasaki+klt+250+backfiring+problem ..

Not mentioned anywhere https://www.google.com/search?q=kawasaki+eliminator+%22EL+175%22+carburetor+size Lots of information for the bigger ones, 'Eliminator' is a whole range of models 125cc to 900cc https://www.google.com/search?q=kawasaki+eliminator+%22EL+175%22+carburetor+replacement ..

Absolutely, the rectifier on your Kawasaki Mean Streak 1500 can be repositioned during a customization project. The rectifier is a crucial part of the motorcycle's electrical system, converting alternating current (AC) from the stator into direct current (DC) to charge the battery and power the bike's electrical components. While relocating the rectifier, it's important to consider a few key factors:

1. Space and Mounting: Assess the available space on the motorcycle to find a suitable location for the rectifier. Ensure that the new position allows for proper mounting and secure attachment without interfering with other components or the bike's functionality.
2. Heat Dissipation: The rectifier generates heat during operation, so it's essential to relocate it to an area with adequate airflow for cooling. Mounting it in a well-ventilated area helps prevent overheating issues.
3. Wiring and Connections: When moving the rectifier, ensure that the wiring can be appropriately rerouted to reach its new location. Take care to maintain proper electrical connections and ensure a secure, stable wiring setup.
4. Protection: Consider adding protective measures, such as shields or guards, to safeguard the relocated rectifier from road debris, water, or other potential hazards.

Modifying the placement of the rectifier may require custom brackets, mounts, or fabrication work to secure it in the desired location. It's crucial to execute the relocation carefully, maintaining proper electrical connections and ensuring the rectifier's safety and functionality. If you're not confident in performing these modifications yourself, consulting a professional motorcycle mechanic or technician with experience in customizations can be highly beneficial. They can offer guidance, expertise, and ensure that the modifications are carried out safely and effectively.

eBay is the only place and there is only one. https://www.ebay.com/itm/266382749570 Or direct from China https://power-tool-batteries.en.made-in-china.com/product/tqRnSCOglNhK/China-Kawasaki-Power-Tool-Batteries-21-6V-Replacement.html Or you can open it up and solder in the individual NiCad cells. Better to replace with NiMH. This is probably why they don't exist, RECALL on the charger. https://www.cpsc.gov/Recalls/2007/alltrade-tools-recalls-power-tool-battery-chargers-due-to-burn-and-laceration-hazards ..

IGNITION SYSTEM for Kawasaki GT750 1992 # KAWASAKI - Online Genuine Spare Parts Catalogue (bike-parts-kawa.com)

We are in North America, so this link might work better for you than it does for me. I can only find a Parts Catalogue and an Owner Manual. https://www.google.com/search?q=kawasaki+kaze+zx130+service+manual ..

I'm assuming you have already checked the actual bulb is still OK? The bike uses a 'twin element' bulb so the tail light element might still work but the brake light element has blown. It's designed to be two bulbs in one so it takes up less space.On a lot of vehicles some electrical features share a fuse and only some of them are marked on the fuse box lid. Has anything else stopped working? On some Kawasaki bikes the brake light shares a fuse with the horn and the tail light so if the fuse has blown all three won't be working. Check the fuse labelled as the Horn to see if that has 'Popped'.*NOTE* ONLY replace fuses with one of the SAME Amp rating as lower 'A' fuses will blow and higher 'A' fuses won't protect your electrics.Bulbs and fuses are usually cheap to buy so you could replace them anyway before thinking it's going to be a 'Big' repair.

If your Kawasaki ZZR600 suddenly stopped firing, there are several possible reasons for this. Here are some troubleshooting steps you can take to identify and resolve the issue:

1. Check the battery: A weak or dead battery can prevent the engine from starting. Make sure the battery is fully charged and has a voltage of at least 12.5 volts.
2. Check the spark plugs: The spark plugs may be fouled, worn out, or damaged. Remove the spark plugs and inspect them for signs of wear or damage. If necessary, replace the spark plugs.
3. Check the ignition system: The ignition coils, ignition module, and wiring may be faulty. Use a multimeter to test the resistance of the coils and check the wiring for continuity. Replace any faulty components as needed.
4. Check the fuel system: The fuel filter may be clogged, the fuel pump may be faulty, or there may be a problem with the fuel injectors. Check the fuel pressure and flow, and inspect the fuel filter and injectors for any signs of clogging or damage.
5. Check the carburetor (if applicable): If your ZZR600 has a carburetor, it may be dirty or clogged. Remove the carburetor and clean it thoroughly with carburetor cleaner.
6. Check the camshaft timing: If the camshaft timing is off, the engine may not fire properly. Check the timing marks and adjust the camshaft if necessary.

If none of these steps resolve the issue, you may need to take your ZZR600 to a qualified mechanic for further diagnosis and repair.

Normally you can't because the ignition is electronic and has an immobilizer. Just buy a new switch or you will have it stolen again. https://www.google.com/search?q=kawasaki+ex250+replacement+ignition+switch ..

There could be several reasons why oil is coming out of the overflow hose on your Kawasaki KDX 220R. Some possible causes include:

1. Overfilled oil tank: If the oil tank is overfilled, oil can get forced out of the overflow hose when the engine is running.
2. Worn or damaged oil seals: If the oil seals in the engine or transmission are worn or damaged, oil can leak out of the engine and into the carburetor, where it can then be forced out of the overflow hose.
3. Clogged or damaged oil cooler: If the oil cooler is clogged or damaged, it can cause excess oil to build up in the engine, which can then be forced out of the overflow hose.

It's important to identify and address the cause of the oil leak as soon as possible, as running the engine with excessive oil can cause serious damage. I recommend taking your bike to a mechanic for a thorough inspection and repair.

Question edited for clarity. Question moved from Cars and Trucks It is here https://kojaycat.co.uk/epages/950000457.mobile/?ObjectPath=/Shops/950000457/Categories/Motorcycle_Wiring_Diagrams/Kawasaki/Z900__KZ900_Z1_Wiring_Diagrams&ClassicView=1 More here https://www.google.com/search?q=Kawasaki+KZ+900+wiring+diagram ..