20 Most Recent 2011 kawasaki ZRX1200 DAEG Questions & Answers


Hi, Anonymous I would love to help you with your engine or chassis noise but I just loaned my brand new pair of listening ears to your local dealer's chief technician so he could take your bike for a test ride and give you his professional opinion and estimate about your noise and repair cost. If you are a little short on "DRACHMA" and a Dealership is not on your list of fun places to visit then perhaps the list below will help soothe your worried mind so you can make an informed decision.
1. Bearings---SCREECH
2. Belts---CHIRP
3. Brake Rotors---BUZZ
4. Rear Chains---RATTLE
5. Cam Chains---CLICKIT
6. Clutches---CHATTER
7. Cylinders---PING
8. Fairing Panels---WHISTLE
9. Fronk Forks---Plunk
10. Gears---WHINE
11. Head Gasket---HISS
12. Hydraulic Lifters---TAP
13. Pistons---SLAP
14. Radiators---GURGLE
15. Rear Chains---RATTLE
16. Rear Shocks---SQUEAK
17. Relays---CLICK&BUZZ
18. Shaft Drives---WHIRR
19. Shifting Trans---CLUNK
20. Solid Lifters---TICK
21. Starters---CLICK
22. Connecting Rods Go---KNOCK-KNOCK---who's there, it's me "*****"
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.kawasakiworld.com/zx-12r/45947-clutch-out-noise.html
motor knocking need serious opinion ZX 14 com
Kawasaki ZRX1200 2001 2007 Workshop Repair Service Manual Download Manuals... $15
OEM Parts for Kawasaki
2003 Kawasaki ZRX1200 Owner Manual

2011 kawasaki... | Answered on Jul 23, 2018


Hi, Anonymous the vast majority of service, parts fiche, and owners manuals on the internet are "FREE" to download and all service manuals contain wiring diagrams in the back pages. The rest usually charge a modest fee of $15 and there is a handful of obscure, rare, obsolete, and very old models that are no longer or never were available and some were never printed in English. The Indian and Philippine markets are usually in E-book format only, for these rare occasions I shall look on eBay and find the cheapest one available. Most of the manuals will cover your exact make, model, and year otherwise one will be provided that comes as close as possible to your bike and will have most of the same info that an exact manual would have. If there is no $ sign after the manual link it is free to download.
To download your manual for viewing or printing please click on the blue links below. Good luck and have a wonderful day
Kawasaki ZRX1200R 2001 2008 Workshop Repair Service Manual Download... $15
OEM Parts for Kawasaki
2003 Kawasaki ZRX1200 Owner Manual
Kawasaki ZRX1200
Kawasaki ZRX1200R

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

2011 kawasaki... | Answered on May 10, 2018


The carb float valve is stuck, or the float needs to be replaced. The oil you see is probably being rinsed off the case by the fuel. Remove the carbs and inspect the condition of the float needle and seat.I would just replace it given the age of the bike. Check the float-if it's brass, shake it to make sure there is no gas in it. If there is, replace it. If it's plastic, put it in a cup of gas and make sure it floats. They do get saturated over time and need to be replaced. When putting it together, consult the factory specs for float level, set it and you should be back on the road. Good luck!

kawasaki ZRX1200... | Answered on Jun 14, 2011


Bikes of that age only need a few things to run.

Compression
Fuel
A spark at the right time

One of those three is defective?

Compression, check with a compression tester
Fuel, is it clean and fresh. Is it getting to the spark plug, it is wet with gasoline?
A spark at the right time. New spark plug and engine correctly timed. A nice fat blue spark if you put the plug against the cylinder head?

kawasaki... | Answered Yesterday


Hi, Anonymous and the usual suspects are:
1. Fouled spark plugs.
2. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
3. Loose connection at ignition coil or plug between ignition sensor and module.
4. Spark plug cables in bad condition, shorting / leaking, spark plug cable connections loose.
5. Faulty ignition coil or ignition / electronic module
6. Failed CKP, CMP, or BAS sensor.
7. Faulty ignition switch.
8. Security alarm failing to disarm needs reset
For more information about your issue and valuable free downloads that you will need please visit the websites below. Good luck and have a nice day.
OEM Parts for Kawasaki
http://www.pdf-manual.com/vehicle/atv/kawasaki/manual-kfx-80-2003-19114.html
9751222 Suzuki Lt80 Service Manual Repair 1987 2006 Lt 80 pdf
No Spark Diagnosis Motorcycle 4 Wheeler Starting Issues Using Multimeter

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e


kawasaki... | Answered on Mar 14, 2019


Exhaust Butterfly Valve - RiderForums.com


https://www.riderforums.com/z1k-z750.../58255-ehaust-butterfly-valve.html

May 25, 2010 - I am getting an error code of 63 which tells me it's the. ... 2007 Kawasaki Z1000 w/ Full Race 4-2-1 Akra, PCIII, K&N, Airbox Mod, Engine Ice, ...

Exhaust install = Service code 63???? - KawiForums - Kawasaki ...


https://www.kawiforums.com/2007.../102064-exhaust-install-service-code-63-a.html

Feb 10, 2008 - 8 posts - ‎4 authors
Join Date: Dec 2007. Location: san ... Has anyone had this code show up? If so, was it ... code 63 is the exhaust butterfly servo. Penna zx6r is ...

FI codes - Kawasaki Z1000 Forum: Kawasaki Z1000 Motorcycle Forums


https://www.z1000forum.com/forum/z1000-service.../141042-fi-codes.html

Apr 8, 2014 - 5 posts - ‎3 authors
Hi is it possible to view FI codes on a 2013 z1k gen 3? If yes what's the ... No i have code 39 ecu communication error. My fan comes on as ... FI Code Quick Chart and Z1000 owner Manual (3rd gen ...
1 post
May 14, 2016
FI Light
10 posts
May 11, 2015
F1 light - Page 3
8 posts
May 6, 2013
More results from www.z1000forum.com

And from our M/C Guru Gregg Mahin

for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Ehaust Butterfly Valve
Kawasaki Fault Codes
Kawasaki Z1000 Service Manual
OEM Parts for Kawasaki
Download Manual 2007 Kawasaki Z1000 Owner Manual

kawasaki... | Answered on Mar 11, 2019


Try looking at the main fuse (30amp) on the starter solenoid. Make sure handlebar run switch is to on position - we all do it! and also check battery connections are tight - especially the negative lead.

kawasaki... | Answered on Mar 05, 2019


From a dealer or Canadian Tire, or a parts place , maybe Walmart.

kawasaki... | Answered on Feb 19, 2019


Hi, Leoj for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Kawasaki Fury 125 fork oil capacity Google Search
Kawasaki Fury Complete Specs
Kawasaki fury 125 manual pdf
2010 Kawasaki FURY 125 FURY 125R AX125AAF OEM Parts
http://mybikemanuals.com/kawasaki

Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e

kawasaki... | Answered on Feb 19, 2019


Hi, Gustavo_h59 and the usual suspects are:
1. Fuel tank empty.
2. The fuel tank has old dead gas.
3. Fuel tank bottom contaminated with ethanol sludge, dirt, water, rust, etc.
4. Fuel supply valve/petcock turned off.
5. Fouled spark plugs.
6. Engine flooded as a result of overuse of the choke.
7. Vacuum hose to the fuel supply valve/petcock disconnected, broken, cracked, or pinched.
8. Fuel valve/petcock or filter clogged.
9. Fuel line to carburetor or throttle body pinched, kinked or blocked.
10. Carburetor float stuck.
11. Fuel injectors clogged.
12. Fuel injectors stuck open.
13. Quick disconnect check ball stuck.
14. Compression below 75 PSI.
15. A stuck-bent-burnt valve.
16. Improper valve clearance (too tight)
17. Severely discharged or a damaged battery should have 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a cursory reading of 12.5 volts or more but little or zero amperage the battery is faulty and must be replaced, AGM batteries fail in this scenario more so than lead-acid batteries.
18. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
19. Loose or corroded wire connection at the coil or plug between ignition sensor and ECM module.
20. Spark plug cables in bad condition and shorting check for spark leakage in the dark, cable connections are loose or connected to the wrong cylinders.
21. Ignition timing incorrect due to a faulty ignition coil, ignition module or MAP, CMP, CKP, O2, TPS, ETP, IAC sensors.
22. Faulty neutral, clutch, kickstand safety switch.
23. Faulty fuel pump or fuse or relay.
24. Faulty or corroded run/stop switch.
25. Tilt sensor needs a reset.
26. Security system not disarming alarm needs a reset.
27. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.kawasakimotorcycle.org/forum/mechanics-corner/146233-86-zl600-eliminator-wont-start.html
https://www.youtube.com/watch?v=l0g7S3BYcFg
https://www.tradebit.com/filedetail.php/181822230-1986-kawasaki-zl500-zl600-service-repair-workshop
$15
https://www.partsfish.com/page/oem-parts-for-kawasaki
https://ownersmanuals2.com/kawasaki/eliminator-600-1997-owners-manual-69007

kawasaki... | Answered on Feb 14, 2019


Hi, Rydsinsane the answer to this question is way above my pay grade for this situation, I would call or visit my local dealer or reputable shop's service/parts department and inquire about any possible quick fix, answers, or parts inquiry.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.motorcyclephilippines.com/forum/index.php?threads/help-please-i-lost-my-fury-keys.265157/
https://www.youtube.com/watch?v=eOyCAbvr4QM
https://www.slideshare.net/BetsyWhite7/kawasaki-fury-125-manual-87099041
https://www.partsfish.com/page/oem-parts-for-kawasaki
http://www.kawasaki-techinfo.net/index.php?view_lang=EN&spec=EU

kawasaki... | Answered on Feb 14, 2019


Hi,Dstanger76 for this scenario you will need your service manual that has all fastener torque specs and a wiring diagram on the back pages, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.riderforums.com/z1k-z750-maintenance/22785-tyre-pressure.html
https://tirepressure.com/kawasaki-motorcycle-tire-pressure
https://www.manualslib.com/manual/815758/Kawasaki-Z750.html?page=1#manual
https://www.partsfish.com/page/oem-parts-for-kawasaki
http://www.kawasaki-techinfo.net/searchOM.php?view_lang=EN&spec=EU&book_no=&lang_code=

kawasaki... | Answered on Feb 14, 2019


Hi, Newtonhassel and the usual suspects are:
1. Severely drained or faulty battery.
2. Faulty regulator/rectifier or high output coil.
3. Faulty power valve, solenoid or installation.
4. Clogged air filter or exhaust.
5. Cracked or incorrect float level.
6. Float needle is not seating.
7. Faulty reed valve.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
https://www.kawiforums.com/2003-2004-zx-6r/192493-bike-will-not-rev-past-8k-like-hitting-rev-limiter.html
https://www.zl-oa.com/community/threads/zl-600-engine-cutting-out-above-5000-rpm.20033/
https://www.tradebit.com/filedetail.php/278482126-kawasaki-zl400-microfiches
$15
https://www.partsfish.com/page/oem-parts-for-kawasaki
http://bikeswiki.com/Kawasaki_ZL400_Eliminator

kawasaki... | Answered on Feb 13, 2019


Hi, Codyblockers for this scenario you will need your service manual, parts fiche, and owners manual if you can't find the best tool you ever bought for your Kawasaki, despair not, for a mere zero $0 you can download another one.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://www.zedder.com/Info/79%20KZ400-B2.htm
https://www.kz400.com/TechnicaltipsFrameset.html
https://www.manualslib.com/manual/849253/Kawasaki-Kz400.html
https://www.partsfish.com/page/oem-parts-for-kawasaki
https://www.amazon.com/1978-Kawasaki-KZ400-Owners-Manual/dp/B008MLPCNY

kawasaki... | Answered on Feb 13, 2019


Hi, Budunka2001 the vast majority of service, parts fiche, and owners manuals on the internet are "FREE" to download and all service manuals contain wiring diagrams in the back pages. The rest usually charge a modest fee of $15 and there is a handful of obscure, rare, obsolete, and very old models that are no longer or never were available and some were never printed in English. The Indian and Philippine markets are usually in E-book format only, for these rare occasions I shall look on eBay and find the cheapest one available. Most of the manuals will cover your exact make, model, and year otherwise one will be provided that comes as close as possible to your bike and will have most of the same info that an exact manual would have. If there is no $ sign after the manual link it is free to download.
To download your manual for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.tradebit.com/filedetail.php/181822230-1986-kawasaki-zl500-zl600-service-repair-workshop $15
https://www.partsfish.com/page/oem-parts-for-kawasaki
https://www.repairmanual.com/product/1986-kawasaki-zl600-a1-motorcycle-factory-owners-manual-r99920-1316-01/
$23
https://www.motorcyclespecs.co.za/model/kawasaki/kawasaki_zl600_86.htm
https://en.wikipedia.org/wiki/Kawasaki_Eliminator

kawasaki... | Answered on Feb 13, 2019


Hi, Tomytittickl the vast majority of service, parts fiche, and owners manuals on the internet are "FREE" to download and all service manuals contain wiring diagrams in the back pages. The rest usually charge a modest fee of $15 and there is a handful of obscure, rare, obsolete, and very old models that are no longer or never were available and some were never printed in English. The Indian and Philippine markets are usually in E-book format only, for these rare occasions I shall look on eBay and find the cheapest one available. Most of the manuals will cover your exact make, model, and year otherwise one will be provided that comes as close as possible to your bike and will have most of the same info that an exact manual would have. If there is no $ sign after the manual link it is free to download.
To download your manual for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
https://www.tradebit.com/filedetail.php/145696279-kawasaki-kdx200-kdx250-servicemanualrepair $15 https://www.partsfish.com/page/oem-parts-for-kawasaki
https://www.manualslib.com/manual/1207233/Kawasaki-Kdx250-1991.html
https://www.motorcyclespecs.co.za/model/kawasaki/kawasaki_kdx250r%2090.htm
https://en.wikipedia.org/wiki/Kawasaki_KDX200

kawasaki... | Answered on Feb 13, 2019


Has it been sitting any good length of time? If so you may need the carburetors cleaned. Also check the air filter and airbox to make sure theres no critters or mouse nests clogging the intake.

kawasaki... | Answered on Feb 02, 2019


I got this free Pdf manual from an online store for free and I don't think Ive visited a mechanic or fixya for help for more than 3-4 times out of the all t he times I fixed the chipper in these 4 years

kawasaki... | Answered on Feb 02, 2019

Not finding what you are looking for?
2011 kawasaki ZRX1200 DAEG Logo

3 questions posted

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

5809 Answers

Marvin
Marvin

Level 3 Expert

84027 Answers

richard libby

Level 2 Expert

202 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

ZRX1200 DAEG kawasaki

  • ZRX1200 DAEG kawasaki

Most Popular Question

knocking noise when engage 1 st gear

  • Motorcycles
Loading...