Top 20 2011 Derbi Senda DRD 125 SM Questions & Answers

The oil light tells you when it has no or low oil pressure. Most often this is simply when the engine is not running as it needs to be running to create oil pressure. The bike not starting is not related to this light. Not starting when it is warm is often an ignition (spark) issue so you need to look at when it last had a tuneup and new spark plug.

I know you said you cleaned the carb, but maybe something got in the carb when trying to start the bike. Because it sure sounds like you have a clogged pilot jet.

Fixya is unable to source parts.

One of these. You buy by make and model, not by size. https://www.google.com/search?q=2008+derbi+terra+flywheel+extractor.

What state is the battery in? Fully charged? Did it work before the overhaul? Check your wires again from top to bottom

Use a airlift or comparable coolant system air removal/refill system.You attach the unit to the coolant system filler and it vacuums all air from the system,then you use the supplied hose to return the coolant into the vacuumed system.This fills the system with just coolant and no air.

cycle oil..30wt..or car

ERZ

probably getting water in the electronics and shorting out take it to a service dealer and see if there is a weather proof system that can be fitted spray the areas with silicone spray or use crc liquid wax to seal off water affected electronics

feel around and under the edges of the seat and there will be a tag that you lift/press to release the seat

Visit two-stroke engine a four stroke one cylinder to cylinder four cylinders if you need to measure the borer and the bike is a part just use calipers or just look it up online

Google is your friend !!!! Good luck http://s675.photobucket.com/user/hmmmnz2/media/randoms/derbisenda-r125.jpg.html

well if you can remove the cable their must be a shop in town that can make a cable like that

DRAIN OLD OIL CHECK LINE/FILTERS REPLACE AS NEEDED ADD NEW OIL.

Typically, push the center of the switch to cancel the signal.

http://www.busytrade.com/products-search/coolant-fluid.html

I can't find a diagram. The small potentiometer on the control board likely serves as an adjustable component to fine-tune specific parameters. Here are some possibilities: Voltage Regulation: The potentiometer might control the output voltage. By adjusting it, you can set the desired charging voltage for different battery types (e.g., 6V or 12V). Current Limit Adjustment: It could be used to set the maximum charging current. Adjusting the potentiometer allows you to limit the charging current based on the battery's capacity and condition. Sensitivity or Threshold: Some potentiometers act as sensitivity controls. For example, it might adjust the threshold at which the charger switches between charging and maintenance modes. Setting the Potentiometer: Without the specific circuit diagram or detailed information about your charger, I recommend the following general steps: Observe the Potentiometer: Identify the potentiometer on the control board. Note its position and any markings (if present). Consult the User Manual: Check the user manual or operating instructions. It might provide guidance on adjusting the potentiometer. Trial and Error: If no specific instructions are available, start with the potentiometer set to its mid-position. Gradually adjust it while monitoring the charger's behavior (e.g., charging current, voltage). Observe how the charger responds to changes in the potentiometer setting. Fine-tune it based on your specific battery type and desired charging characteristics. Remember that precise adjustments depend on the charger's design and the battery you're charging.

The bike doesn't exist as written. https://www.google.com/search?q=410JS+1000cc+santana We are better with 'year make model 1000cc'. Better to not try and do better than the bike engineers. A mechanical pump runs when the engine is turning, an electric pump will run as soon as the key is turned and create pressure all the time. It would have to be an in tank electric pump or it will burn out. Electric pumps are cooled an lubricated by the fuel passing through it. If it is a carbureted engine, you are pressurizing the carb bowl. If injected, it may already have a fuel return. Check the mechanical pump for a torn diaphragm, they are easy to change. ..

The lift cables on a 1993 model 2693 Hilo camper are 30 feet,2 3/4 inches long and fit the standard height lift of 11 feet 8 inches high to the top of the overhead. The lift uses two cables. According to a Hi- Lo camper travel trailer forum, cable replacement is basically the same on all years and models, with the main difference being the length of the cables from model to model. You can use a cable cut chart to find what cable length you need for your camper, and you'll need to know your year, model name, and box (body) length: Lift cables typically wear out after three to five years, so it's important to replace them as needed and keep them regularly maintained.

This is a combo unit. Confirm the disc is playable. The problem may not be in the machine. Check that the power plug is firmly inserted. I have provided links to manuals for the machine. If the troubleshooting therein fails, the remaining option appears to be contacting the manufacturer. Such details should be in the manuals. Pioneer XV-BD707 Blu-Ray Disc Receiver Manual ' HiFi Engine PIONEER XV-BD707 OPERATING INSTRUCTIONS MANUAL Pdf Download ' ManualsLib