Top 20
2009 Cpi GTR 50 Questions & Answers
Torque settings for 2008 cpi supermoto 50
TIGHTENING TORQUES
DESCRIPTION (MM) TORQUE (NM)
FRONT AXLE NUT 12 60
REAL AXLE NUT 16 120
FRONT FORK BRIDGE
CLAMPING SCREWS 8 20
BRAKE CALIPER
BOLTS 8 25
HANDLEBAR
MOUNTING BOLTS 34 --
SUSPENSION
STRUT LOWER
FASTENING BOLT 6 12
ENGINE HANGER
BOLTS 8 20
TRANSMISSION
HOUSING
FASTENING SCREWS -- --
ENGINE CASE 6 12
CYLINDER HEAD 7 14-16
Flywheel 12 45
Clutch drum --- ---
Clutch --- ---
Transmission oil
draining plug 8 10
Kick starter 6 12
Manifold 6 12
Muffler 6 / 8 12 / 20
Bolts / nuts
without defined
stipulations 6 12
8 20
10 40
12 60
Spark plug 14 15
GTR 50cc scooter. Where is spark plug?
Spark plug is fitted into the cylinder head - somewhere!
Cylinder head is at the top of the engine that has a vertical or nearly-vertical cylinder or with a horizontal cylinder is usually the forward-most part.
Spark plug has a thick wire connected to it so if you can see a thick wire try following it...
If you are thinking of replacing your bike's spark plug, take great care when refitting. The threads are fine and cross-threading is easy to do so always fit the new plug and screw in at least two full turns by hand and take great care not to overtighten it.
Most new spark plugs are fitted with a collapsible washer to ensure a gas-tight seal. The washer can be felt collapsing in the last approximately 60 - 90 degrees of turning and equally it can be easily felt when it has finished collapsing. From that point it needs only a few pounds of additional pressure on a 6 inch wrench to finish the job.
When refitting a plug with a used washer, once contact with the cylinder head is made, it only needs that small amount of wrench pressure for it to be tight enough.
Cpi crab 100
use motor oil or an engine oil for your engine, as long as it is with this sae or saf number as advise by manufacturer and use gear oil for your gear box with the same sae number as advised by manufacturer. you can use any brands you want as long as the numbers of oil matches.
Need circuit diagram for ARLEC 15e 6-24Volt 15Amp Electronic battery charger OR their later model BC58
I can't find a diagram.
The small potentiometer on the control board likely serves as an adjustable component to fine-tune specific parameters. Here are some possibilities:
Voltage Regulation:
The potentiometer might control the output voltage. By adjusting it, you can set the desired charging voltage for different battery types (e.g., 6V or 12V).
Current Limit Adjustment:
It could be used to set the maximum charging current. Adjusting the potentiometer allows you to limit the charging current based on the battery's capacity and condition.
Sensitivity or Threshold:
Some potentiometers act as sensitivity controls. For example, it might adjust the threshold at which the charger switches between charging and maintenance modes.
Setting the Potentiometer:
Without the specific circuit diagram or detailed information about your charger, I recommend the following general steps:
Observe the Potentiometer:
Identify the potentiometer on the control board. Note its position and any markings (if present).
Consult the User Manual:
Check the user manual or operating instructions. It might provide guidance on adjusting the potentiometer.
Trial and Error:
If no specific instructions are available, start with the potentiometer set to its mid-position.
Gradually adjust it while monitoring the charger's behavior (e.g., charging current, voltage).
Observe how the charger responds to changes in the potentiometer setting.
Fine-tune it based on your specific battery type and desired charging characteristics.
Remember that precise adjustments depend on the charger's design and the battery you're charging.
4/9/2024 5:47:52 AM •
Motorcycles
•
24 views • 2 helpful votes
What is the length of lift cables on a 1993 model 2693 hilo camper and any info on what after market part to use ? thanks
The lift cables on a 1993 model 2693 Hilo camper are 30 feet,2 3/4 inches long and fit the standard height lift of 11 feet 8 inches high to the top of the overhead. The lift uses two cables. According to a Hi- Lo camper travel trailer forum, cable replacement is basically the same on all years and models, with the main difference being the length of the cables from model to model. You can use a cable cut chart to find what cable length you need for your camper, and you'll need to know your year, model name, and box (body) length: Lift cables typically wear out after three to five years, so it's important to replace them as needed and keep them regularly maintained.
4/11/2024 2:06:02 PM •
Motorcycles
•
18 views • 1 helpful votes
Cleaned my carburetors and the Jets and now my bike won't start. I have a spark but it won't start.
All questions need FULL 'year make model', as the first 3 words.
Then there are 10,000 categories listed by 'make year model'.
So we are working blind.
Make sure gasoline is being delivered to the carbs by removing the fuel delivery pipe.
Carbs come in different systems. If it has a float bowl on the bottom, tap it with the handle of a screwdriver as it may be stuck.
Turn the engine over. If it doesn't start, remove the spark plug and see if it is wet with gas?
You need three things for an engine to start
Clean gas
A spark at the right time
Compression
You have one thing missing
//
2/21/2024 5:36:50 PM •
Motorcycles
•
30 views • 0 helpful votes
Not finding what you are looking for?