20 Most Recent
2008 Xispa Xy260T4 - Page 9 Questions & Answers
Recalibrating on safety stop
It's not uncommon for dive computers to experience slight variations in depth measurements during safety stops, particularly in rougher conditions. However, if your Cressi Leonardo is consistently recalibrating at this depth range and you are concerned about its accuracy, you may want to have it serviced or inspected by a certified technician to ensure that it is functioning properly.
Additionally, it's important to note that during a safety stop, it is recommended to maintain a constant depth to prevent decompression sickness. If you find it difficult to maintain a steady depth due to rough conditions, it's important to adjust your buoyancy and position yourself appropriately to avoid any sudden movements that may affect your safety stop.
2/22/2023 3:48:41 AM •
Motorcycles
•
Answered
on Feb 22, 2023
How to remove crank on tunturi exercise bike.
The bolt at the crank arm needs to first be loosened using an adjustable wrench in order to remove the crank on a Tunturi exercise bike. Pull the crank arm away from the bike after the bolt has been released. If this doesn't work and you hear a clicking noise, it may be necessary to either tighten the crank arm further or service the crank bearings. It is preferable to take the bike to a bike shop in this situation so that it may be serviced.
2/14/2023 9:53:17 PM •
Motorcycles
•
Answered
on Feb 14, 2023
On. Cdi 32900-19b00 where do wires go
The wiring diagram for your 4-wheeler should provide you with specific instructions on how to wire the components. Generally speaking, white/blue is the positive wire, black/red and black/yellow are the negative/ground wires, green is the start switch, blue is the kill switch and black is the headlamp.
2/14/2023 6:02:33 PM •
Motorcycles
•
Answered
on Feb 14, 2023
What is the wire running up the hood hinge on the passenger side of a 2004 jeep grand Cherokee Laredo
It is difficult to determine the exact purpose of the wire you are describing without a visual inspection of your vehicle, but it is possible that it is a ground wire for the hood light. Some vehicles have a hood light that illuminates the engine compartment when the hood is opened, and this light may require a ground wire to function properly. However, without more information or a visual inspection, it is impossible to say for certain what the wire is for.
2/14/2023 4:44:22 AM •
Motorcycles
•
Answered
on Feb 14, 2023
What is the positive and neutral and ground order on the dc charging cord for a dsr115
The positive and neutral order on a DC charging cord for a DSR115 (or any other device) is typically standardized and is determined by the specifications set by the manufacturer of the device.
Typically, the positive wire on a DC charging cord is identified by being red, and the neutral wire is identified by being black. The ground wire (if present) is typically identified by being green.
It is important to note that these wire colors are standardized, but there may be exceptions, so it is always best to consult the manufacturer's specifications to confirm the positive, neutral, and ground wire assignments for a specific device.
2/13/2023 12:43:19 PM •
Motorcycles
•
Answered
on Feb 13, 2023
I have a 98 tl 1000 it throws a code of f1 and runs horrible shooting flames out of the pipes
It sounds like your 1998 TL 1000 has a major problem. The F1 code typically indicates an issue with the fuel system, so you may need to check the fuel injectors and replace any faulty or clogged ones. Additionally, make sure all of the hoses and fuel lines are connected properly, as well as check for any signs of damage or corrosion. If everything looks good there, then it's possible that you may need to replace the fuel pump or other internal components.
1/30/2023 5:37:06 PM •
Motorcycles
•
Answered
on Jan 30, 2023
Mio Soul i 125 rear axle nut tightening torque value
The tightening torque value for the rear wheel nut of a Yamaha Mio Soul i 125 motorcycle is typically around 70-80 Nm (Newton meter). This torque value is the amount of force required to tighten the nut to the proper level.
It's important to use a torque wrench to tighten the nut, this will ensure that the nut is tightened to the proper torque level without over tightening it, which can cause damage to the threads or the hub.
It's also important to note that the torque value may vary depending on the specific model and year of the motorcycle, so it is best to consult the owner's manual or the manufacturer's website for the specific torque value for your motorcycle.
It's also important to check the torque every time you change a tire or make any adjustment to the wheels, to ensure that the wheels are properly secured and to prevent accidents or damage to the motorcycle.
1/24/2023 7:49:49 AM •
Motorcycles
•
Answered
on Jan 24, 2023
2001 softailduece cable throttle: i sprayed contact cleaner in switches due to starter sticking .tried loosening adjusters but no twist
It sounds like there may be an issue with the cable throttle on your 2001 Softail Deuce motorcycle after using contact cleaner on the switches. Here are some things you can try to fix the problem:
- Check the cable for any kinks, frays or breaks. If the cable is damaged, it will need to be replaced.
- Check the cable routing and make sure it is not bound or pinched.
- Check the cable adjusters to make sure they are not seized or stuck.
- Check the throttle grip for any damage or wear, and make sure it is properly lubricated and adjusted.
- Check the throttle control mechanism and make sure it is properly lubricated and adjusted.
- Check the carburetor or fuel injection system to make sure they are properly adjusted and functioning correctly.
- If the above steps do not resolve the issue, it may be best to take the motorcycle to a professional technician or contact the manufacturer for further assistance or service.
It is important to note that, the above steps are general troubleshooting steps, and the actual problem can be caused by different things, so it is best to consult a service manual for your specific 2001 Softail Deuce motorcycle or contact the manufacturer for more detailed and accurate information.
1/23/2023 1:01:08 PM •
Motorcycles
•
Answered
on Jan 23, 2023
How do I get rebuild kit for 250cc benzhou 2007 with proper specifications for piston
You can try contacting the manufacturer of the scooter, Benzhou, to see if they have a rebuild kit available for the 2007 250cc model. You can also check with local scooter or motorcycle shops to see if they carry rebuild kits for that specific scooter model. Additionally, you can try searching online for aftermarket rebuild kits for the Benzhou 250cc scooter. Be sure to specify the year and model of your scooter when searching to ensure you get the proper specifications for the piston.
1/22/2023 4:32:44 AM •
Motorcycles
•
Answered
on Jan 22, 2023
What is the torque specs for a 97 Harley electro glide?
The torque specifications for a 1997 Harley-Davidson Electra Glide will vary depending on the specific components of the motorcycle. Here are some general torque specifications for a 1997 Harley-Davidson Electra Glide:
- Engine oil drain plug: 25-35 ft-lbs
- Transmission drain plug: 25-35 ft-lbs
- Transmission fill plug: 25-35 ft-lbs
- Primary cover bolts: 25-35 ft-lbs
- Clutch hub nut: 60-80 ft-lbs
- Timing cover bolts: 25-35 ft-lbs
- Cylinder head bolts: 80-100 ft-lbs
- Rocker arm cover bolts: 25-35 ft-lbs
- Rocker arm adjusting screw lock nut: 25-35 ft-lbs
- Rocker arm pivot shaft nut: 25-35 ft-lbs
- Pushrod cover bolts: 25-35 ft-lbs
- Pushrod tube clamp bolt: 25-35 ft-lbs
- Oil pump cover bolts: 25-35 ft-lbs
- Oil pump drive gear nut: 25-35 ft-lbs
- Oil filter adapter cover bolts: 25-35 ft-lbs
- Oil cooler lines: 25-35 ft-lbs
- Oil pressure sender switch: 25-35 ft-lbs
- Oil pressure relief valve: 25-35 ft-lbs
- Oil pressure switch: 25-35 ft-lbs
- Oil pressure gauge sender: 25-35 ft-lbs
Please note that these are general torque specifications and it's recommended to check the service manual for your specific 1997 Harley-Davidson Electra Glide for the most accurate information. Additionally, it's always recommended to consult a professional mechanic or a Harley-Davidson dealer for advice, even if you're a seasoned motorcycle mechanic.
1/20/2023 10:18:41 AM •
Motorcycles
•
Answered
on Jan 20, 2023
How to bench sync 1977 GS750 throttle slide height
The baseline throttle slide height for a Suzuki GS750 motorcycle should be set so that the slides are fully closed when the throttle grip is in the closed position. This means that when you twist the grip fully counterclockwise to the stop, the slides should be flush with the carburetor body.
To adjust the throttle slide height, you will need to remove the carburetors from the bike and use a feeler gauge to measure the gap between the bottom of the slide and the carburetor body.
It is important to make sure the throttle cables are properly adjusted before setting the throttle slide height. The throttle cables should be adjusted so that the throttle grip moves the slides smoothly and the grip is in the closed position when the slides are fully closed.
It is also important to keep in mind that the carburetors on a Suzuki GS750 motorcycle should be synchronized after adjusting the throttle slide height. This ensures that all carburetors open and close at the same time and at the same rate, which is necessary for proper engine performance.
Please note that this is a general explanation and the specific process may vary depending on the year or model of your Suzuki GS750 motorcycle. It's recommended to consult the service manual for your specific bike for detailed instructions on adjusting the throttle slide height and synchronizing the carburetors.
1/20/2023 10:17:18 AM •
Motorcycles
•
Answered
on Jan 20, 2023
Not finding what you are looking for?