20 Most Recent 2007 kawasaki Ninja ZX6R - Page 2 Questions & Answers

If your Kawasaki ZZR600 suddenly stopped firing, there are several possible reasons for this. Here are some troubleshooting steps you can take to identify and resolve the issue:

1. Check the battery: A weak or dead battery can prevent the engine from starting. Make sure the battery is fully charged and has a voltage of at least 12.5 volts.
2. Check the spark plugs: The spark plugs may be fouled, worn out, or damaged. Remove the spark plugs and inspect them for signs of wear or damage. If necessary, replace the spark plugs.
3. Check the ignition system: The ignition coils, ignition module, and wiring may be faulty. Use a multimeter to test the resistance of the coils and check the wiring for continuity. Replace any faulty components as needed.
4. Check the fuel system: The fuel filter may be clogged, the fuel pump may be faulty, or there may be a problem with the fuel injectors. Check the fuel pressure and flow, and inspect the fuel filter and injectors for any signs of clogging or damage.
5. Check the carburetor (if applicable): If your ZZR600 has a carburetor, it may be dirty or clogged. Remove the carburetor and clean it thoroughly with carburetor cleaner.
6. Check the camshaft timing: If the camshaft timing is off, the engine may not fire properly. Check the timing marks and adjust the camshaft if necessary.

If none of these steps resolve the issue, you may need to take your ZZR600 to a qualified mechanic for further diagnosis and repair.

Normally you can't because the ignition is electronic and has an immobilizer. Just buy a new switch or you will have it stolen again. https://www.google.com/search?q=kawasaki+ex250+replacement+ignition+switch ..

There could be several reasons why oil is coming out of the overflow hose on your Kawasaki KDX 220R. Some possible causes include:

1. Overfilled oil tank: If the oil tank is overfilled, oil can get forced out of the overflow hose when the engine is running.
2. Worn or damaged oil seals: If the oil seals in the engine or transmission are worn or damaged, oil can leak out of the engine and into the carburetor, where it can then be forced out of the overflow hose.
3. Clogged or damaged oil cooler: If the oil cooler is clogged or damaged, it can cause excess oil to build up in the engine, which can then be forced out of the overflow hose.

It's important to identify and address the cause of the oil leak as soon as possible, as running the engine with excessive oil can cause serious damage. I recommend taking your bike to a mechanic for a thorough inspection and repair.

Question edited for clarity. Question moved from Cars and Trucks It is here https://kojaycat.co.uk/epages/950000457.mobile/?ObjectPath=/Shops/950000457/Categories/Motorcycle_Wiring_Diagrams/Kawasaki/Z900__KZ900_Z1_Wiring_Diagrams&ClassicView=1 More here https://www.google.com/search?q=Kawasaki+KZ+900+wiring+diagram ..

If your 1991 Kawasaki Voyager radio is working, but the volume is very low, there could be a few possible causes for this issue. Here are a few troubleshooting steps you can try:

1. Check the volume level on the radio itself. Make sure that the volume is turned up all the way and that the mute function is not enabled.
2. Check the volume level on any external devices (such as a smartphone or MP3 player) that may be connected to the radio. Make sure that the volume on these devices is turned up as well.
3. Check the wiring and connections for the radio. Make sure that all of the connections are secure and that there are no damaged or frayed wires.
4. Check the speakers for the radio. Make sure that the speakers are properly connected and that there is no damage to the speakers or the wiring.
5. If the volume is still low after trying these steps, it's possible that there may be an issue with the radio itself. In this case, you may need to have the radio repaired or replaced.

Question edited for clarity. Wiring Diagram and Service Manual is in the link https://www.google.com/search?q=1992+kawasaki+750+volcano+wiring+diagram ..

https://www.manualslib.com/manual/733813/Kawasaki-Brute-Force-750.html

Most VIN numbers have to be stamped on the frame by the triple tree, left side or right side. Basically right in front of the fuel tank but will be readable without removing the tank. It will read up and down and will be 17 digits long. Depending on how old the bike is it might be on the bottom frame close to the engine but will also be stamped into the frame. Let me know what you find and I can give you another place to check, Daniel.

https://www.kawasakimotorcycle.org/threads/no-power-at-all-2000-gpz-1100.155008/ This thread may help you find your problem

Question edited for clarity MAKER. Question moved from Cars and Trucks! https://www.google.com/search?q=kawasaki+zg1000+replace+neutral+sensor ..

https://www.kawasakimotorcycle.org/threads/clutch-cable-problems.33401/ Here is a forum that might help you.

for future reference include year https://www.quadcrazy.com/files/file/279-kawasaki-bayou-400-service-manual/

Yes put some BG Cleanr in tank for carb. Also inspect ign parts..bike is 30yr..components get worn n git hot causin firing issues.Buy a clymer Haynes or chilton manual taday

The Service Manual is here https://mototh.com/en/file/65/page/3 wiring diagrams https://www.google.com/search?q=2009+kawasaki+ninja+650r+ignition+wiring+diagram&rlz=1C1QJDB_enCA643CA644&sxsrf=ALiCzsZkicC5VnJPU0cjlF-z8nE_JZG3rw:1657468727948&source=lnms&tbm=isch&sa=X&ved=2ahUKEwjmtYWW2O74AhUhJX0KHbukBfsQ_AUoAnoECAEQBA&biw=1920&bih=937&dpr=1 ..

Visit: Repair ManuelClub.com
There you will find EXACTLY what your looking for OR: WOLFRAM ALPHA.COM

close enough https://www.manualslib.com/manual/796425/Kawasaki-Eliminator-125.html?page=295 ..

Ideas in the link. You only need three things

1. Clean fuel
2. A spark at the right time.
3. Compression

https://www.google.com/search?q=1989+Kawasaki+600+Katana+no+start ..

Get a shopbook online. Compression cud b weak or fuel supply. Timing cud b off or batt not holden charge

In general It's always a good idea to do a complete clutch assembly all at once, especially if there is more than one clutch plate/ring. Before you start stripping the clutch down check the simple silly stuff first. Check all the linkages from the lever to the actual clutch. The issue could just be the cable or a linkage sticking. Check the cable sleeve is routed correctly as a tight turn in it can also cause it to bind. If you can release the cable or get some slack on the cable, operate the clutch lever at the gearbox end with your hand. If it's stuck it's a clutch issue if it moves it's a cable or linkage issue. How many miles are on the bike? Higher mileage? Do the whole clutch. If it's a Very Low mileage you will probably get away with just the friction plates. *Note* If the bike has been ridden HARD this can also wear a clutch out faster. If you've got the clutch stripped down take a Very good look at ALL the rings and plates on both sides and if there is any wear or damage change the whole thing.