Kymco Motorcycles - Page 2 - Recent Questions, Troubleshooting & Support

https://www.manualslib.com/manual/890872/Kymco-Venox-250.html ------ this is service manual

Some ideas in the link. If it fuel injection, clean the throttle body. https://www.google.com/search?q=2014+Kymco+450i+stalls+out+when+I+lower+the+throttle ..

you dont need vin for parts year make model -----dealer --atv repair shop--online search for parts

Check the videos https://www.google.com/search?q=Kymco+Maxer+mobility+scooter+replace+rear+wheel ..

a SCOOTER. year 2000. not cc (LOL) cloned version of Honda's AF18E/AF16E Dio motor. Air cooled, 49cc, single cylinder, 2-stroke Compression Ratio: 7.2:1 it's in the manual. RTM" service manual there is computer model to calc, this using compression ratio and cylinder volume but here is generic list. my lawn mower is 100psi;. (and mopeds and outboard tiny motors and scooters tiny not 250cc hog scooters) my old car is 150psi my newer car with high 10:1 CR , is 200psi a 49cc engine 7.2 CR is like 80psi. low and expected. at that CR, 100 max to get the reading correctly good guage fast cranked (kicked or starter turned) let the meter peak and peak is spec. read peak PSI and the CR is what matters. and only on a warm engine, warm/hot not cold cold is way less. when warm the rings seat, cold they do not.(well)

Question edited for clarity, name of the maker Kimco > Kymco. Question moved from Cars and Trucks to correct category. It is a model from 2012. Are you sure you have the 150cc and not the 50cc? They are restricted to 50mph. You said "55 mph going down a hill with the wind at our back". Were you riding with a passenger, or it "our", you are the scooter? A 150 wouldn't do well with a passenger, and you would have to take into consideration your combined weight. This is the specs, but take into account the Chinese are short, petite, lightweight people. How fast does a KYMCO 150 go? between 60 and 70 MPH Kymco's U.S. distributor told me that the 150's top speed is between 60 and 70 MPH and that the 250's top speed is between 70 and 80 MPH.

Kymco PEOPLE 150 Reviews on Cycle Insider

Here are some specs and reviews, but basically, if you want speed, you need a 250, scooters in general are not very aerodynamic! Of get a Honda Fireblade and do One HUNDRED and Sixty Five!

https://www.google.com/search?q=2021+kymco+super+8+150x+top+speed ..

I thight it might be fuel injected but it isn't. I has a standard carburetor, so the tank is standard gravity feed. Looks like the second tube might be a vacuum hose to suck tank fumes for emmisions control. Here is the manual. https://manualmachine.com/kymco/hipster/7117078-user-manual/ https://www.google.com/search?q=kymco+hipster+150+fuel+system ..

hello again: Always best to buy parts direct from the manufacturer in Taiwan. If you just lost the 2 keys, you could ask a locksmith to just make you a new pair. A Kymco dealer should be able to supply replacement keys based on the lock number. https://www.google.com/search?q=kymco+like+150+replace+ignition+switch ..

Question edited for full make model cc. Likely to be yes. Test it with a multimeter. Service Manual https://kymco.at/pub/media/Download/Kymco/WHBVenox250.pdf https://www.google.com/search?q=2009+venox+no+ignition ..

Fault in drive lever. Lever does not reset. https://www.manualslib.com/manual/1055934/Kymco-Super-8-Foru.html?page=57

https://www.manualslib.com/manual/892435/Kymco-Maxer.html?page=39#manual

It is here 80/65 - 8"

New Inner Tube 80/65-8 Black For Kymco Agility EQ35FA ...

https://www.wheeliegoodmobility.com > new-inner-tub... This is a New Inner Tube 80/65-8 Black For Kymco Agility EQ35FA Mobility Scooter. Please refer to the image. International shipping is available. ..

Moved Category from Cars & Trucks to Kymco. This is a known issue and the Kymco Forum says it may be from using an incorrect key. There is a workaround. https://www.google.com/search?q=2012+Kymco+50i+key+security+shutter+closes ..

WHAT DOES IT TELL YOU ON THE TIRE SIDE WALL

There are three possible sources of power. 1. The light control assay is a module that determines when to cut power to the lights when at idle or starting the engine... it can fail and prevent power from going to the lights. 2. The CDI. It sends a signal to the Light Control Module... if no signal, no lights. 3. The light switch. The wires can get lose and prevent power from going to the LCM. Start at the Switches. Test for power from the switch, if no power from the switch, make sure power is going to the switch. Flip the switch from low to hi beam too, test both lines. The CDI is a bit trickier to test but there is a wire to the LCM that can be powered when the bike is running (a bad CDI is diagnosed after everything else though as it is difficult to test and very unusual to happen). If power is going to the LCM, that rules out the switches. If you confirm power to the LCM, and power from the CDI (a signal from it at least), then its a bad LCM. But check your light bulbs before doing anything. If you bypass the LCM on an American bike (connecting the blue wire to the LCM to the blue wire from the LCM together), it will blow the fuse but some European and Phillipine models work without the LCM. LCM's and CDI's aren't cheap so have a professional confirm the parts are bad before replacing.

On my kymco foru midi the tyer presure is 25 to 28

Chinese rubbish

Fuse replacement needed.

Try eBay or a motorcycle part finder site And on the problem of it reoccurring difficult to say as need to know what damage was caused to piston and valves Was it just one rocker arm that broke or is the other damaged did the timing jump and piston hit open valves driving them up and breaking arm and damaging cam shaft lobes You really need to find out why and how it happened As it may require a complete timing system replacement on that cylinder cam shafts , rocker arms , valves ,drive sprockets top and bottom , drive chain and a piston

Chinese pish, get rid of it