Keeway AX 100C - Popular Questions, Answers, Tips & Manuals

You have a bad ignition module.

Weak return spring? Is routed correctly so it doesn't pull when the hadlebars are moved?

My oil pump packed up so i use 32-1 mixture which equates to approxamately 125ml 2 stroke per 4 ltrs of petrol

Hello and happy thanksgiving from the USA. I would suspect that you have a defective igntion switch, the igntion switch is what powers up all of the electrical system when you turn the key to run, the contacts can get burnt or the connector or both. The switch is under/behind the ignition key cylinder which operates the switch or course.

Regulator fault

Hello
We do not hany repair manuals for any type of motorcycle or scooter, they are copyrighted and not free to obtain for download, sorry. To obtain a service manual for the scooter you will need to contact the parts dept. of any dealership that sells these. I am not aware of any dealers in this state and have never seen this brand in the USA (We are based in San Mateo, Calif). Good Luck

@tomhorton47Hi I have the same question ! What gear oil should I replenish with ?

Look at the sidewall of both tires. There will be a 'MAX PSI' embossed on the tire. It will probably say Max 45 PSI. At 45psi the bike will ride like a rock. At 15psi it will ride really squirrely. Find a psi at which you feel the bike handles well and rides well. One rider may weigh 125 pounds and the next rider may weigh 300 pounds. The best psi for each rider will be different due to weight. Chances are that 30 to 35 psi will do the trick. Please take a moment to rate my answer. Thanks.

Have you checked the battery? Also if you have a voltage regulator in your scooter it is possible that it could be out resulting in a loss of all power. Let me know what you find out, Jeff from fixya

remove the spark plug and place it on top of the block,attach the cable socket connected to CDI,now start using auto switch or kick starter...now look if there's a current...

* if has,then check the block (carbonize if possible) and pistons

* if not,check electrical wirings, some lines might be grounded...






please rate me if this solution helps...thanks

What exactly is it doing when you try to start it? A slow, lazy start is commonly a low charged or weak battery. Just spinning and not trying to start is often a 'No Spark' issue. Turning, trying to start but stalling out is usually a fuel supply problem.

Keeway say they do, but they don't appear to. Haynes do one though. https://www.google.com/search?q=2017+Keeway+TX+125+Supermoto.+Service+manual ..

Not available online either. https://www.google.com/search?q=2017+Keeway+TX+125+Supermoto.+wiring+diagram ..

Spark, Fuel, Air. With the spark plug hooked to the wire and the spark plug removed, hold the diode to a ground while you crank it and see if there is a spark.

If you have verified that there is a spark, that the scooter is getting fuel, and that the starter motor is working, and the scooter is still not starting, there are a few other things you can try to troubleshoot the issue:

1. Check the ignition system to make sure it is functioning properly. This includes the ignition switch, the ignition coils, and the ignition timing.
2. Check the compression in the engine. If the compression is low, it may be difficult for the engine to start.
3. Check the valve clearance to make sure it is within the specified range. If the valve clearance is incorrect, it may affect the engine's ability to start.
4. Check the fuel pump to make sure it is functioning properly. If the fuel pump is not working correctly, it may not be delivering enough fuel to the engine.
5. Check the carburetor to make sure it is clean and properly adjusted. If the carburetor is not functioning correctly, it may be difficult for the engine to start.

If you have checked all of these items and the scooter is still not starting, it may be necessary to consult a mechanic or the scooter's user manual for further troubleshooting.

I don't have specific information on a 2014 Keeway TX125 motorcycle. However, I can provide you with some general information about fuel lines in motorcycles. The fuel lines in a motorcycle connect the fuel tank to the carburetor or fuel injector. They carry fuel from the tank to the engine, allowing the combustion process to take place. The fuel lines are typically made of rubber or plastic, and they can become brittle and cracked over time, leading to leaks. In most motorcycles, there are two fuel lines: one for fuel delivery and another for fuel return. The fuel delivery line carries fuel from the tank to the carburetor or fuel injector, while the fuel return line carries excess fuel back to the tank. The fuel return line helps to regulate fuel pressure and prevent vapor lock. It's important to make sure that the fuel lines in your motorcycle are properly connected and in good condition. A fuel leak can be dangerous and cause damage to your motorcycle. If you're not sure how to properly connect the fuel lines on your Keeway TX125, I would recommend consulting the motorcycle's owner's manual or taking it to a certified mechanic for assistance.

In the link https://www.google.com/search?q=valve+clearance+on+keeway+superlight+200cc+motorbike ..

Make sure batt is 12.6v no less. Carb can b cleand w BG. Compression cud b weak

Since all electrical works the same regardless of the vehicle, I would suspect that you've got a couple of grounds making contact where they shouldn't (power flow through). I would recommend getting a volt meter that can check for OHMS and trace each line to determine it's function and polarity since on vehicles most things work when you give them 'ground'. From there, label each one somehow (tape, dots with a permanent marker ect) so you can keep the grounding wires separate from the positive or 'charged' ones. I hope this helps and good luck!

find a real mechanic that can reason out the failure and fix the fault indicates a problem in the adjustment or a cable problem or if hydraulic , air in the system