Cars & Trucks - Page 8 - Recent Questions, Troubleshooting & Support


What are we working on? Carburetor system or fuel injection? Sounds like there may be a cross fire in the firing order.
What happened or changed to start this problem? Was there some type of work done to the engine?
There is a lot of missing information. Does the vehicle have a OBDll system so that you can hook up a scanner? If so , do that and and see what information you can get from it.

Cars & Trucks | Answered 22 hours ago


To replace the power steering belt on this model you need to loosen the 2 mounting bolts for the pump (12mm head), loosen the tensioner nut (12mm head), remove the belt from the pulley, remove the horizontal bolt through the engine mount (17mm head), remove the 2 vertical motor mount bracket bolts under the poser steering pump (14mm head). This should allow you to remove the belt and install the new one. If I can assist further, reach me at https://www.6ya.com/thericepatch

Acura Cars &... | Answered 22 hours ago


What is it you wish to know about it?

Cars & Trucks | Answered 22 hours ago


I'm not certain what your question is, if you are inquiring about the dificulty, it is moderate, possibly including evacuating the system and removing the compressor. On most v6 models, coil/clutch replacement cannot be done with the compressor on the vehicle. If I can assist further, reach me at https://www.6ya.com/thericepatch

2004 Acura MDX | Answered 22 hours ago


It could be a number of things on this model. The first and most likely culprit would be the main relay located under the dash. If the check engine light does not come on for 3 seconds when turning the key on, this is going to be your problem. If the check engine light comes on and you hear the fuel pump prime then I would lean toward the distributor. There are a number of other possibilities but these are the most common on that model. If I can assist further, reach me at https://www.6ya.com/thericepatch

Acura Cars &... | Answered 22 hours ago


I FOUND THIS WEB SITE that I think will help you with this question and a lot more. Since this web site will have access to many different vehicles I hope you do not feel like I am lazy by just passing along the web site instead of giving you the exact information you asked for.



Go to this site to find a manual to help you.
https://www.browsemanuals.co/lander_zrk65_test14.html?t1=1535071160&t2=65192170713&t3=kwd-28425796&gclid=EAIaIQobChMI-oybpN624AIVwdVkCh2GtguWEAEYASAAEgJ9yvD_BwE

Chrysler Cars &... | Answered 22 hours ago


If replacing the front bulb, typically it can be accessed from the fender well by pulling back the black plastic in front of the tire. If replacing a rear, there should be an access cover in the trunk that will allow you access to the inside of the tail light assembly. If I can assist further, reach me at https://www.6ya.com/thericepatch

Acura Cars &... | Answered 22 hours ago


Here are the instructions for installing your Thermostat. 2.0 and 2.7 are basically the same. The only difference is 12-14 ft.lbs.

To install:
  1. Thoroughly clean the thermostat housing and mating surface. Make certain to remove all gasket material.
  2. Position the thermostat on the engine.
  3. Install a new gasket onto the housing and install the housing.
  4. Secure the housing with the retaining nut and bolt. Tighten both fasteners to 11-14 ft. lbs. (15-20 Nm).
  5. Raise the vehicle and tighten the drain ****.
  6. Install the undercover.
  7. Lower the vehicle and refill the cooling system.
  8. Connect the negative battery cable.
  9. Run the engine until hot and verify proper cooling system operation.

2006 Kia Sorento | Answered 22 hours ago


Likely the ignition switch is not rotating completely into the off position. If your key is extremely worn, it may be possible it can be removed without the switch exactly in the off position. Suggest trying a different (less used) key and see if problem goes away.

Else try to make sure it is in off position (clock off) before removing key. If you find that's the problem you may need new keys or switch or both.

1994 Toyota... | Answered 22 hours ago


It could be oil pressure is low, in which case shut off engine and haul to shop. Or it could be a false indicator, i.e. faulty oil pressure sense circuit (sending unit/cable/connect).

Cadillac Cars &... | Answered 22 hours ago

Not finding what you are looking for?
Cars & Trucks Logo

2,135,219 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

83959 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22441 Answers

john h

Level 3 Expert

19466 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...