1991 Jeep Wrangler Logo

Related Topics:

Posted on Jul 26, 2011
Be the first to answer

I have a 95 warangler...when the guy put a new body on he forgot to hook up the fuel pump..unfortunately i cant find where the wiring comes from in the front end..i have a haynes and it doesnt really help its the 4.0

Answer This Question

5 Related Answers

ZJLimited

ZJ Limited

  • 17989 Answers
  • Posted on Jul 15, 2008

SOURCE: wiring for fuel pump 95 jeep cherokee

Check the Page 105 -->> Fuel System Wiring Diagram

Ad
FoRdMaStEr

Ernest Stalker

  • 53 Answers
  • Posted on Jan 06, 2009

SOURCE: Radio prob

is it a factory or aftermarket stereo system. if it is an aftermarkek system you are going to have to run your own fused power source from the battery to the amp

Anonymous

  • 1615 Answers
  • Posted on Nov 17, 2009

SOURCE: my 95 yj hard too start after i change my fuel

when it does not start you need to verify no fuel pressure, Most likely your problem is the wiring harness is bad which will destroy a new pump if the pump is not geting the voltage required.

Testimonial: "thanks very much!! "

Anonymous

  • 1902 Answers
  • Posted on Jun 16, 2011

SOURCE: digram for a 2004 jeep

The ground wire is in the wire harness that connects to the fuel pump. This sounds more like the relay is bad. Check the relay under the hood. Your model also has a fuse that can pop and cause the same issue.

Anonymous

  • 1 Answer
  • Posted on Nov 27, 2011

SOURCE: excessive fuel consumption, backfire on decelleration, and rough idle

check your pre-cat or even main cat-converter

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

I have a 95 f150 w/ inline 6 4.9l, I have replaced both fuel pumps, Fuel pressure regulator, cleaned and/or replaced all sensors, still very hard to start
things to check what is fuel pressure --are pumps getting full voltage --egr valve--throttle body [clean -rebuild-replace] --cat converter --vacuum leaks
Read full answer
Mar 16, 2022 • Cars & Trucks
0helpful
1answer

95 jeep wrangler runs sumwhat come to stop stalls loose fuel pressure put new pump in dose same hear pump run when turn key dont think it is get constant power with key in run position cant figure
Sounds like you should look into your fuel pressure regulator.
Amazon com Omix Ada 17711 01 Fuel Pressure Regulator Automotive
Read full answer
Sep 03, 2018 • Jeep Cars & Trucks
1helpful
1answer

New fuel pump worked now dosen't 95 accliam
Check the condition of the fuel pump relay first and the condition of the wiring in both connectors inside and outside of tank second. Check condition of the ground wire return where it attaches to body- it may be broken or corroded. Inside of the tank as well. Also check to see if you have 12 volts at the pump- if not, check fuse and other wiring for damage.

Also check to make sure the oil pressure switch is intact and functioning correctly.
Read full answer
Oct 06, 2012 • 1995 Plymouth Acclaim
8helpful
3answers

Just changed fuel pump in 95 gmc jimmy now it wont start where is the gas kill switch
when the key is turnned on do you hear the fuel pump run? if not find the ground wire or wires coming off the fuel pump they are bolted to the frame with a wire brush and or sand paper clean the frame and the wire eyelet for the ground and try restarting it If I'm not mistaken the fuel pump is in the gas tank and you should replace the sending unit as well as the fuel pump... Then check to make sure your getting fuel to your engine... If you are then it has to be spark/fire...lack of that is...Good Luck
Read full answer
Oct 05, 2011 • 1995 GMC Jimmy
0helpful
1answer

I have a 90 lincoln 5.0 motor in a 46 mercury coupe... I just put an aftermarket wiring kit in it; it ran before i did the wiring changeover, now it doesn't... I put a new tfi module in it, still no...
I've got code 95 as a fuel pump secondary circuit failure eca to ground.
Meaning your computers are looking for the fuel pump shut off and not finding it. I don't have the schematic on the 5.0 but the 3.0 was a pnk/blk wire hot: blk ground hooked to terminal 8 on the ECC module. and I know you can wire the 2 together so you should be able to ground out the safety switch terminal to make the computer happy. Hope this helps.
Read full answer
Mar 02, 2011 • 1990 Lincoln Town Car
0helpful
2answers

I have a 99 s10,we thought fuel pump went out and we replaced it,2 weeks later out again took bed off and it started right up so we went over everything clean grown wire and no brakes,did it again ,so we...
tap on the fuel pump relay when the problem pops up. It may have an internal fault. cheap to replace.
Read full answer
Oct 29, 2010 • 1999 Chevrolet S-10 Pickup
0helpful
1answer

I am replacing a fuel pump for a 1998 s10, i took the old one out and put the new one in the connection is differnt, i think i hook it up right, but i cant get the pump to come on
YOU COULD HAVE THE WRONG FUEL PUMP IF HOOK UP DIFFERENT.THE PUMP WIRING DIFFERENT ALSO.
Read full answer
Jun 25, 2010 • 1998 Chevrolet S-10 Pickup
0helpful
1answer

I have a 1983 nissan 720 pickup and it has and outside mounted fuel pump. the power wire fell off of it now it doesnt work and i cant find anywhere on the pump where to put the power wire back on.. i need...
If the wire broke off close to where it enters the fuel pump body you wont be able to reattach the wire without disassembling the pump body to resolder the broken wire leads inside. I would recommend finding a new universal style replacement pump at a discount auto parts store as I did on an 84 king cab. You may have to mount a bracket and re plumb some new fuel line also.
Read full answer
Aug 13, 2009 • 1983 Nissan Pickup
1helpful
1answer

Is their a fuel pump in tank of E350 7.3 diesel 1988 ford ?
my guess is there is a fuel pump in tank as there are in 95% of diesel motor vehicles. you may have just sucked out the existing fuel from the lines. the fuel pump can withstand high amounts of amperage and voltage so by hooking up wires wrong i dont think you burned up the pump but you may have wired it up wrongly, or you have forgot to put the o rings back inthe housing properly. or drop on in tank. check the fel system setup. Orings in place, wiring connected properly. if all else fails give the pump a hit and see if it will start.
Read full answer
Aug 09, 2009 • Ford E-350 Cars & Trucks
0helpful
3answers

Want start
pls give me ur problem in more detailed and good explanation
Read full answer
Jun 12, 2009 • 1991 GMC Sonoma
Not finding what you are looking for?

View Most Popular

1991 Wrangler

  • Cars & Trucks

Related Question

I have a 95 f150 w/ inline 6 4.9l, I have replaced both fuel pumps, Fuel pressure regulator, cleaned and/or replaced all sensors, still very hard to start

  • Cars & Trucks

22 views

Ask a Question

Usually answered in minutes!

Popular Questions

2002 jeep wrangler 6 cylinder:

2002 Jeep Wrangler

Why does check eng light come on and engine starts to sputter

1995 Jeep Wrangler

Poor gas mileage on my jeep liberty

2005 Jeep Wrangler

I Need to see the fuse box diagram for a 1991 jeep

1991 Jeep Wrangler

Heater blows cold air

2004 Jeep Wrangler

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Jeep Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...