Question about 1993 Volkswagen Jetta

Open Question

Jetta 3 -hard start , unstable idling and no power , i suspect the valves .if the valves is bend what must i do? ...what are the sequence and torque specifications and the cam nuts?

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Dennis Boxerman

  • 1300 Answers

SOURCE: torque specifications for head bolts 1995 Jetta 2.0

You should really go to an auto parts place and buy a manual. This something you really should not cut corners. It will give you the specs and the sequence of how to torque the head. You will also need to know how to set the timing in relation to the cam and crank. Manual is well worth the money. It has pictures, instructions, and such.

Good Luck

Posted on Feb 21, 2009

Ad

Anonymous

  • 1392 Answers

SOURCE: torque specs for front spindle (nut hold brake drum in place)

Tighten till the wheel bearing is tight. No one really uses a specification for that, do it by feel. when the nut is tight, and there is no play in the bearing. Should be about 15-20 ft/lbs, with about .001-.003 end play if you need exact numbers though.

Posted on May 30, 2009

mgray87

  • 15 Answers

SOURCE: VW Jetta torque setting and hub nut size????

129 ft/lbs. Per Bentley...I'm pretty sure it's a 30 mm 12 point socket.

Posted on Jun 01, 2009

dsacco86

Devon Sacco

  • 1077 Answers

SOURCE: VW LUG NUT TORQUE SPECIFICATIONS 1965 BETTLE 5 BOLT

With the normal lug bolt with 17mm head, torque them down at 80 ft pounds. Replace them if looks to be worn out.

Posted on Apr 16, 2010

Testimonial: "THANK YOU"

tburtk

burt

  • 158 Answers

SOURCE: i need torque specs for a 2004 dodge cummins 24

http://www.dieseltruckresource.com/dev/index.php

I suggest this website for your dodge truck needs.

Posted on May 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 VW Jetta 2.5L Cold Start Idle speed Unstable


run fault codes and check for ambient temp sensor and/ or MAP/MAF sensor problems.

Mar 16, 2014 | Cars & Trucks

1 Answer

Good day, can anyone help me with torque specs and sequence for a 2002 volkswagen jetta 1.8L cylinder head to engine block.


The 2002 service manual says replace stretched bolts. stage I: 30 ft-lb (40Nm) stage II: additional 1/4 turn, stage III: another 1/4 turn. Start in center, work your way out diagonally back and forth (crossways) ending on the ends of the block. Do this sequence on each stage.

Sep 16, 2013 | 2001 Volkswagen Jetta TDI

1 Answer

Is there a proper way or sequence to torque the valve cover on a 1993 300E mercedes-benz


START IN THE CENTER VALVE COVER GOING FROM LEFT TO RIGHT CRISS CROSS SEQUENCE SHOULD GIVE YOU A EVEN TORQUE ON VALVE COVER GASKET.

May 08, 2011 | Mercedes-Benz E320 Cars & Trucks

1 Answer

Can't find cylinder head torques!!! please advice....


Torque sequence: ----------------- there are two rows of fasteners and you need to start with the middle 2 fasteners first and then work your way toward the front and back in steps. Step 1: torque head bolts #1,2,3,4,5,6,7, & 9 in sequence to 10 Ft/Lbs Step 2: torque head bolts #1,2,3,4,5,6,7, & 9 in sequence to 20 Ft/Lbs Step 3: torque head bolts #1,2,3,4,5,6,7, & 9 in sequence to 29 Ft/Lbs Step 4: turn all head bolts in sequence an additional 90 degrees Step 5: turn all head bolts in sequence an additional 90-degrees recheck final torque in sequence. Fasteners are supposed to be replaced if they are removed since they are torque-to-yeild fasteners.

7 - 5 - 1 - 3 - 10
front
9 - 4 - 2 - 6 - 8

Apr 17, 2011 | 1997 Toyota Previa

2 Answers

Anyone know sequence and torque specs for a Volkswagen JETTA 2.0 L, AEG cylinder head?


Per Chiltons...
Step 1: 30 ft lbs
Step 2: 44 ft lbs
Step 3: Plus 90 degrees
Step 4: Plus 90 degrees
Here is the tightening sequence...
10 4 2 6 8
7 5 1 3 9

Mar 06, 2011 | 2001 Volkswagen Jetta TDI

1 Answer

Jetta 2 unstable idle loss in power once engine warmd up it wont start again


Hi

Most likely cause is either the air mass sensor also known as the MAF sensor or the 02 oxygen sensor, I would go with air mass firstly as they are cheaper and you can clean them, and they can last much longer.

Hope this helps
Regards
Dan

Jan 04, 2011 | Volkswagen Jetta Cars & Trucks

1 Answer

Can i change a leaking top gasket at home? I want to remove the head and have it skimmed.I am reasonally mechanical minded. What is the torque for fastening the top nuts? Manie vd Merwe. Jeffreys Bay


VOLKSWAGONS YOU NEED CYLINDER HEAD REMOVE SEQUENCE AND CYLINDER HEAD TORQUE SEQUENCE.YOU NEED A REPAIR MANUAL FOR TORQUE SEQUENCE OR YOU WILL HAVE HEAD GASKET LEAKS. TORQUE HEAD BOLTS TO * STEP 1 * TORQUE BOLTS 30 FT LBS * STEP TWO * TIGHTEN BOLTS 44 FT LBS STEP 3 TIGHTEN BOLTS PLUS 90 DEGREES.* STEP FOUR* TIGHTEN BOLTS PLUS 90 DEGREES AGAIN.

Oct 02, 2010 | 1999 Volkswagen Jetta

1 Answer

1991 Jetta missing through rpm band, not idle


you need 2 people for this
  1. pull up e brake as hard as you can
  2. hold foot brake
  3. put it in drive and
  4. rev up motor till it misfires
  5. while its misfiring
  6. look for bad wires arcing across the valve cover
  7. and spray the intake with carb clean to see if there is intake leaks.

Mar 23, 2010 | 1991 Volkswagen Jetta

1 Answer

How to adjust Ford 460 heads?


9 5 1 3 7 10 6 2 4 8 This is the head bolt sequence which should be torqued to 130-140 ft-lbs

Note: the numbers are represenative of the bolt location.

Mike...

Nov 24, 2009 | 1982 Ford F 250

1 Answer

2004 jetta timing belt is missing teeth and jumped timing it is not working anymore but it didn't break do you think there is valve damage


For sure. Make sure you have the proper torquing sequence for your engine BEFORE you tear it apart. The head has to be taken off in the reverse sequence for torquing or you run a high risk of cracking the head and buying a new one. Hope thishelps.

Oct 11, 2009 | 2004 Volkswagen Jetta

Not finding what you are looking for?
1993 Volkswagen Jetta Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Marvin
Marvin

Level 3 Expert

85206 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...