Question about 2006 Mazda Tribute

Open Question

I have a 2006 mazda tribute manual...when the engine is running low rpm...there is a cloinking noise when you press the gas pedal and release the clutch pedal........

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 76 Answers

SOURCE: 2006 Mazda Tribute: Gas pedal keeps sticking when I excelarate!

locate the cable from the motor. disconnect,hold up high spray wd-40 into cable,lots cause you want it to run all the way through

Posted on Mar 13, 2009

Ad
  • 811 Answers

SOURCE: looking for front end parts diagram for 2006 mazda tribute

buy manual, clean or replace speed sensor at wheels

Posted on Sep 13, 2009

  • 35 Answers

SOURCE: 2005 Mazda Tribute gas pedal freezes in cool

Throttle cable could be binding inside the housing that attached to the throttle body. Also the throttle positioning sensor could be faulty as well.

Posted on Dec 14, 2009

  • 6 Answers

SOURCE: stuck clutch pedal on a Mazda B series truck

Replace both clutch slave and master cylinders, and bleed well. I've also had this happen.

Posted on Dec 14, 2009

01fordeb
  • 1033 Answers

SOURCE: gas pedal unresponsive

Try this: Go to your local parts store and purchase a can of (throttle body cleaner) you will take your air filter out and remove the big tubing that is connected to your throttle body and filter housing. Spray the cleaner inside the throttle body, open the (butterfly) and spray around the pivot the butterfly opens and close on. What happens is you get carbon build up in these areas and it causes the gas pedal to feel like it's stuck and have to apply more pressure to the pedal. You will see alot of black carbon run out of the throttle body. Take a clean rag and wipe down the area of the throotle body. Repeat the cleaning 1-2 times. put your air inlet tubing back on and re-install your filter. It may seem hard to start at first but it's drying out the cleaner that was sprayed inside the body. Try this and see if this works. I've done this on many vehicles that shops want to charge $300 to do and all you need is $5 cleaner. It's very easy to do and takes 20 min.

Posted on Jan 24, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

F22a engine produces strange noise most obvious at 2000 rpm, what could the problem be?


Without a general description of what the noice sounds like, squeal as compared to knocking, it is impossible to help you. Engines make a lot of different noises, so try and help by describing noise. I would suspect it is belt related, or tension pulley related as these are RPM variable noises, belts tend to slip when you accelerate and can be quite loud with a serpentine belt as example.
CERACOAT-NANOTECH.com

May 14, 2015 | 1996 Honda Accord

1 Answer

Mazda tribute


I'd the check engine light on? Have you checked to see what codes are present if it is on?

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Apr 10, 2014 | 2002 Mazda Tribute

1 Answer

Engines shuts down when idling Car starts if accelerating but shutsoff when gas pedal is released.


You have an air flow problem. It could be a dirty air filter, or a vacuum leak (hissing noise) or a clogged catalytic converter. All three of these will cause a shut down at idle and poor fuel economy.

Oct 02, 2011 | 2001 Mazda Tribute

1 Answer

Hello, My 2010 Mazda 5 is having engine ping/knock issues, the dealers cannot hear anything, but it happens since two months ago and I am sure it is the engine knocks, not anything else. It happened...


It's called lugging, and it will happen with any manual trans car at low speed in a high gear. Nothing wrong -- it's a hint that you need to downshift . . .

Mar 23, 2011 | 2006 Mazda 5

1 Answer

2005 Mazda Tribute gas pedal freezes in cool weather


Throttle cable could be binding inside the housing that attached to the throttle body. Also the throttle positioning sensor could be faulty as well.

Dec 14, 2009 | 2006 Mazda Tribute

2 Answers

Throtle pedal is hard to push in cold weather 2006


I don't have the solution but I can back you up, my 2006 Tribute does the same thing when it's around freezing the first time or two I push on the gas.

Oct 30, 2009 | 2006 Mazda Tribute

3 Answers

2006 Mazda Tribute: Gas pedal keeps sticking when I excelarate!


locate the cable from the motor. disconnect,hold up high spray wd-40 into cable,lots cause you want it to run all the way through

Mar 13, 2009 | 2006 Mazda Tribute

Not finding what you are looking for?
2006 Mazda Tribute Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

Marvin
Marvin

Level 3 Expert

85178 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...