WINDSHIELD WIPER REMOVAL - 2001 Chevrolet Blazer

REMOVAL

1. Raise and support the hood.
2. Remove the windshield wiper pivot arms.
3. Remove the cowl top vent panels.

1. Disconnect the windshield wiper mounting arm and pivot shaft.

1. Remove the access cover from the dash panel.
2. Remove the mounting arm and pivot shaft retaining clip.
3. Disconnect the windshield wiper mounting arm and pivot shaft from the windshield wiper motor.

1. Remove the windshield wiper motor.

1. Disconnect the electrical connector.
2. Remove the three bolts.
3. Remove the windshield wiper motor.

INSTALLATION

1. Install the mounting arm and pivot shaft retaining clip on the windshield wiper mounting arm and pivot shaft.

1. Install the windshield wiper motor.

1. Place the windshield wiper motor in the dash panel.
2. Install the three retaining bolts.
3. Reconnect the electrical connector.

1. Reconnect the windshield wiper mounting arm and pivot shaft.

1. Press on the windshield wiper mounting arm and pivot shaft after it is aligned with the windshield wiper motor.
2. Install the access cover in the dash panel.

1. Install the cowl top vent panels.
2. Install the windshield wiper pivot arms.
3. Adjust the windshield wiper pivot arms.

This is technically for the V6 4.2L but I'm sure those Ford E250's have the same setup for windshield wiper motor. Let me know how it goes.

Windshield Wiper Motor
Removal & Installation
To Remove:

1. Remove wiper arms.
   
2. Remove weatherstrip from cowl.
   
3. Remove two cowl vent grille panel screws.
   
4. Remove windshield nozzles and hoses.
   
5. Remove three cowl vent grille panels.
   
6. Disconnect windshield wiper motor electrical connector.
   NOTE: Do not remove crank arm from windshield wiper motor.
   
   
7. Loosen nuts that attach the drive link brackets to the crank arm.
   
8. Remove wiper motor crank arm brackets.
   
   
   
   
   
   
   
   
   
   
   
9. Remove three bolts and windshield wiper motor from vehicle.

To Install:

1. Install windshield wiper motor and three bolts.
   
   
   
   • Torque to: 62 in lbs. (7 Nm)
   
   
2. With right side linkage closest to the windshield wiper motor, install drive
   link brackets to wiper motor crank arm.
   
   
   
   • Torque nuts to: 44 in lbs. (5 Nm)
   
   
3. Connect electrical connector.
   
4. Install nozzles and windshield washer hoses to cowl vent grille.
   
5. Install three cowl vent grille panels and screws to vehicle.
   
6. Install weatherstrip to cowl.
   
7. Install wiper arms.

Remove the cover located at windshield base with flatblade screw driver or other prying device. Remove retaining bolt, then while prying under wiper arm where it is attached to wiper motor shaft, wiggle wiper arm side to side and up & down. Don't be scared.

go to our villager site for help. The wiper motor has a governor assy, that is what you are referring to. What is the problem?
Windshield Wiper Governor Removal
The windshield wiper governor (17C476) is located on the LH side of the engine compartment behind the battery (10655) .

1. Remove the two windshield wiper governor screws and the windshield wiper governor .
   
2. Disconnect the two windshield wiper governor electrical connectors.
   

http://groups.yahoo.com/group/villagerquest/

why do you think the motor still works if the wipers don't move? Can you hear the motor run or can you see a little movement when you turn the switch on?

What happens when you activate the washers?

go to a salvage yard that allows you to remove the parts yourself. Then you can see how the motor and linkage assembly comes out.


don't have 1983 info, but here is 1994:

Section 01-16A: Wiper and Washer System, Ranger/Explorer 1994 Ranger and Explorer Vehicles Workshop Manual
DESCRIPTION AND OPERATION Windshield Wiper System, Ranger/Explorer The windshield wipers are actuated by a permanent magnet, rotary-type electric windshield wiper motor (17504) . The two windshield wiper pivot arms (17526) and windshield wiper blades (17528) are mounted on a pivot shaft, one at each side of the windshield. The windshield wiper mounting arm and pivot shaft (17566) are connected to the motor by windshield wiper adapter and connecting arm clip (17531) . Ranger and Explorer vehicles are equipped with an interval wiper and washer (IWW) system featuring a lever-type turn signal and windshield wiper switch (13K359) mounted on the steering column. The IWW windshield wiper governor (17C476) uses a relay contact to control current to the windshield wiper motor . The governor electronic circuitry controls the contact to supply current to windshield wiper motor . A rear wiper/washer system is available on Explorer vehicles. The rear window wiper system consists of a windshield wiper motor mounted inside the liftgate (40010) , an articulating windshield wiper pivot arm and windshield wiper blade , a windshield wiper/washer switch (17A553) and an inline circuit breaker. The front electric windshield washer system consists of a control switch, integral with the turn signal, a windshield washer reservoir (17618) and windshield wiper motor and the necessary windshield washer hoses (17A605) , windshield washer nozzle jet and brackets (17603) and attaching parts.
------------------------------------------------------------------------------------------------
Pivot Shafts and Linkage Removal and Installation
NOTE: The left and right pivot and windshield wiper adapter and connecting arm clip assemblies are serviced separately.

1. Perform Steps 1 through 9 of Windshield Wiper Motor Removal as described in this section.

1. If servicing left windshield wiper adapter and connecting arm clip , remove left windshield wiper mounting arm and pivot shaft and windshield wiper blade assembly.

1. Remove left windshield wiper adapter and connecting arm clip access cover.

1. Remove left pivot nut, lower windshield wiper adapter and connecting arm clip and slide it out through left access opening. For installation, follow removal procedures in reverse order. Tighten nut to 10-13 Nm (7-10 ft-lb). Make sure the clip is fully seated in the windshield wiper adapter and connecting arm clip . Do not try to install clip with windshield wiper adapter and connecting arm clip on motor crank pin.
   

----------------------------------------------------------
Windshield Wiper Motor Windshield wiper motor are not serviceable. If worn or damaged, the windshield wiper motor must be replaced as an assembly. Removal

1. Cycle windshield wiper blades until in straight-up position and turn ignition switch OFF.

1. Disconnect battery and wiper motor electrical connector.

1. Remove the right windshield wiper mounting arm and pivot shaft and windshield wiper blade .

1. Disconnect the battery ground cable (14301).

1. Remove the right pivot nut and allow the windshield wiper adapter and connecting arm clip to drop into the cowl top outer panel .

1. Remove the linkage access cover, located on the right side of the dash panel near the windshield wiper motor.

1. Reach through the access cover opening and unsnap the wiper motor clip.

1. Push the clip away from the windshield wiper adapter and connecting arm clip until it clears the nib on the crack pin. Then, push the clip off the windshield wiper adapter and connecting arm clip.

1. Remove the windshield wiper adapter and connecting arm clip from windshield wiper motor crank pin.

1. Remove nut and ground strap.

1. Remove three attaching nuts from windshield wiper motor. Remove the windshield wiper motor .

Installation

1. Position the windshield wiper motor and install the three attaching screws. Tighten to 13.6-19.0 Nm (10-14 ft-lb).

1. Install nut and ground strap.

1. Connect wiper motor electrical connector.

1. Install clip completely onto right windshield wiper adapter and connecting arm clip. Make sure the clip is fully seated. Do not put the windshield wiper adapter and connecting arm clip on the motor crank pin and then try to install the clip.

1. Install the left windshield wiper adapter and connecting arm clip onto the wiper motor crank pin.

1. Install the right windshield wiper adapter and connecting arm clip onto the wiper motor crank pin. Pull the windshield wiper adapter and connecting arm clip onto the crank pin until it snaps into place. The clip is properly installed if the nib is protruding through the center of the clip.

1. Install the right windshield wiper mounting arm and pivot shaft and nut. Tighten the nut to 9.5-12.5 Nm (84-110 in-lb). NOTE: When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the powertrain control module (PCM) (12A650) relearns its adaptive strategy. The vehicle may need to be driven 10 miles or more to relearn the strategy.
   

1. Connect the battery ground cable and turn the ignition switch on. Turn turn signal and windshield wiper switch off so windshield wiper motor will park, then turn ignition switch off. Replace right windshield wiper adapter and connecting arm clip access cover.

1. Install the windshield wiper mounting arm and pivot shaft and windshield wiper blade assemblies on the pivot shafts to dimension X. Dimension X is the distance between the centerline of the blade saddle and the top edge of the cowl top outer panel grille. The value of Dimension X for each vehicle is given in the Dimension X chart in the Specifications portion of this section.

1. Test the system.

2002 Ford F-250 Windshield Wiper Motor Removal & Installation 1. Turn the ignition switch to the ON position. Turn the ignition switch ON until the wiper blades are straight up, then turn the ignition switch OFF. 2. Disconnect the negative battery cable. 3. Remove the right-hand and left-hand windshield wiper arm and blade assemblies. 4. Remove the cowl top vent panels. 5. Detach the electrical hardness connector at the windshield wiper motor assembly. 6. Remove 3 wiper motor (module assembly) retaining bolts and remove the module assembly from the vehicle. 7. Remove the wiper linkage retaining bolt and remove the linkage from the wiper motor. 8. Remove 3 retaining nuts and remove the windshield wiper motor To install; 9. Place the windshield wiper motor in position and install 3 retaining nuts. Tighten to 10-12 ft. lbs. (12-17 Nm). 10. Connect the wiper linkage to the windshield wiper motor and install the retaining bolt. Tighten the bolts to 14 ft. lbs. (20 Nm). 11. Place the wiper motor (module assembly) in position and install 3 retaining bolts. Tighten the bolts to 6 ft. lbs. (9Nm). 12. Install the electrical hardness connector to the windshield wiper motor. 13. Connect the negative battery cable. 14. Allow the windshield wiper motor to cycle several times while checking for proper wiper motor operation. 15. Turn the windshield wiper motor to the OFF position to park the wiper motor in the park position. 16. Install the cowl top vent panels. 17. Install the wiper arm and blade assemblies. Install the retaining nuts and tighten to 22-29 ft. lbs. (30-40 Nm). 18. Connect the negative battery cable. 19. Check the windshield wiper motor for proper operation and the wiper arms for adjustment.

Wiper Pivot Arm Removal and Installation

1. Lift the windshield wiper pivot arm to the full upright position.

1. Remove the windshield wiper pivot arm.
   1. Release the locking tab.
   1. Remove the windshield wiper pivot arm.

1. NOTE: During installation, it is necessary to pull the locking tab out to its full open (unlatched) position and hold while assembling the pivot arm onto the mounting arm and pivot shaft. Align the key on the pivot arm head with the keyway on the shafts. This will make sure the pivot arm is correctly aligned. If necessary, the key can be removed. To adjust wiper pivot arms, refer to Wiper Blade and Pivot Arm Adjustment in this section.
   To install, reverse the removal procedure.

SECTION 501-16: Wipers and Washers 1999 Town Car Workshop Manual REMOVAL AND INSTALLATION Mounting Arm and Pivot Shaft Removal

1. Disconnect the battery ground cable (14301).

1. Remove the windshield wiper pivot arms (17527).
   1. Remove the nuts (one each side).
   1. Remove the windshield wiper pivot arms.

1. Remove the LH and RH cowl top vent panels.
   1. Remove the hood weatherstrip.
   1. Remove the screws.
   1. Remove the retaining clips.
      • Disconnect the LH and RH washer hoses.

1. Position the windshield wiper mounting arm and pivot shaft (17566) assembly aside.
   1. Remove the nuts.
   1. Remove the bolt.
   1. Position the windshield wiper mounting arm and pivot shaft assembly aside.

1. Remove the windshield wiper mounting arm and pivot shaft assembly.
   1. Disconnect the electrical connector.
   1. Remove the windshield wiper mounting arm and pivot shaft assembly.

----------------------------------------------------------------------------------------
Motor —Windshield Wiper Removal

1. Remove the windshield wiper mounting arm and pivot shaft (17566) assembly; refer to Mounting Arm and Pivot Shaft .

1. Remove the windshield wiper motor (17508).
   1. Remove the output shaft bolt.
   1. Remove the bolts.
   1. Remove the windshield wiper motor.

I have 2007 only. please rate as solved if this is what you needed. good luck.

SECTION 501-16: Wipers and Washers 2007 Freestar/Monterey Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 04/27/2006
Wiper Motor — Windshield Printable View (104 KB) Removal

1. Remove the windshield wiper arms.

1. NOTE: Disconnect the washer hose before removing the cowl panel grille.
   Remove the pushpin-type retainers and the cowl panel grille.

1. Remove the washer hose grommet from the cowl panel and position aside the washer hose.

1. If equipped, remove the A/C air inlet filter.

1. Remove the 9 cowl panel bolts and position aside the cowl panel.

1. Disconnect the windshield wiper motor electrical connector.

1. Remove the cowl panel from the vehicle.

1. Remove the 4 bolts and the windshield wiper motor.

Installation

1. Position the wiper pivot arms on the windshield wiper motor and install the bolt.
   • Tighten to 15 Nm (11 lb-ft).

1. Install the 3 windshield wiper-to-cowl panel bolts.
   • Tighten to 15 Nm (11 lb-ft).

1. Position the cowl panel in the vehicle and connect the windshield wiper motor electrical connector.

1. Install the washer hose and grommet in the cowl panel.

1. Install the 9 cowl panel bolts.
   • Tighten to 6 Nm (53 lb-in).

1. If equipped, install the A/C air inlet filter.

1. Position the cowl panel grille in the vehicle and connect the washer hose.

1. Install the pushpins.

1. Install the windshield arms and nuts.
   • Tighten to 27 Nm (20 lb-ft).

1. Cycle and park the windshield wipers to check for correct alignment.

Pivot Shafts and Linkage
The windshield wiper assembly is mounted below cowl top extension (021A36) . Linkages are connected with non-removable plastic ball joints. Windshield wiper mounting arm and pivot shafts are an integral part of the windshield wiper and are serviced as one unit. Removal

1. Disconnect the battery ground cable (14301). Refer to Section 14-01 .
   

1. Remove antenna mast from the antenna base.
   

1. Remove cap on LH and RH windshield wiper pivot arms to expose nuts retaining the arms to pivot shafts.
   

1. Remove two nuts, one from each of windshield wiper pivot arms . Lift wiper arms to service position, carefully rocking them back and forth to loosen them from the pivot shaft. Lift off windshield wiper pivot arms .
   

1. Remove seven screws retaining the cowl top vent panel.
   

1. Disconnect windshield washer hose (17A605) at LH side of vehicle just ahead of where it enters cowl top.
   

1. Remove hood cowl seal.
   

1. Carefully remove cowl top vent panel from vehicle.
   

1. Remove three retaining screws to cowl drain tube that is connected to top cowl.
   

1. Disconnect wiring harness leading to windshield wiper motor.
   

1. Remove five screws retaining cowl top to vehicle and remove cowl top and windshield wiper from vehicle.
   

1. Remove two screws and two nuts retaining windshield wiper to cowl top and separate the two parts.
   

1. Remove drive linkage from motor shaft linkage.
   

1. Remove remaining screws attaching windshield wiper and separate the two parts.
   

Item Part Number Description 1 02010 Cowl Top Panel 2 N621906-S2 Nut (2 Req'd) 3 17508 Windshield Wiper Motor 4 N805605-S36 Screw (2 Req'd) 5 17500 Windshield Wiper Assembly A — Tighten to 9-12 Nm (80-106 Lb-In)