After battery change on my 2001 avalon the time/date reset to default even I set the time/date correctly then turn off the ignition and turn back on again then the time/date reset to default again .

After changing the oil and filter, reset the monitor by proceeding as follows:

Turn ignition On, but do not start engine.

Fully depress and release accelerator pedal three times within five seconds.

If CHANGE ENGINE OIL lamp flashes for five seconds, this indicates system has reset.

Start engine. OIL LIFE should change to 100%.

If CHANGE OIL SOON lamp lights again, repeat reset procedure.

2001-08 Silverado, w/Driver Information Center

Turn ignition On, but do not start engine.

Press MODE button until DIC (Driver Information Center) reads OIL LIFE LEFT/HOLD SET TO RESET.

Press and hold SET button until 100 percent is displayed. You will hear 3 chimes and CHANGE ENGINE OIL SOON message will go off.

Turn ignition Of


how to reset oil life on 2004 chevy silverado

Without Date Display
AM/FM Base Radio with a Single CD Player
This type of radio has a button for setting the time. You can set the time by following these steps:
Turn the ignition key to ACC/ACCESSORY or ON/RUN. Press the knob, located in the center of the radio, to turn the radio on.
Press the button until the hour begins flashing on the display. Press the button a second time and the minute begins flashing on the display.
While either the hour or the minute numbers are flashing, turn the knob, located on the upper right side of the radio, clockwise or counterclockwise to increase or decrease the time.
Press the button again until the clock display stops flashing to set the currently displayed time; otherwise, the flashing stops after five seconds and the current time displayed is automatically set.
To change the time default setting from 12 hour to 24 hour, press the button and then the pushbutton located under the forward arrow label. Once the time 12H and 24H are displayed, press the pushbutton located under the desired option to select the default. Press the button again to apply the selected default, or let the screen time out.

With Date Display
Single CD (MP3) Player
This type of radio has a button for setting the time and date.
To set the time and date, follow these instructions:
Turn the ignition key to ACC/ACCESSORY or ON/RUN. Press the knob, located in the center of the radio, to turn the radio on.
Press the button and the HR, MIN, MM, DD, YYYY (hour, minute, month, day, and year) displays.
Press the pushbutton located under any one of the labels that you want to change. Every time the pushbutton is pressed again, the time or the date if selected, increases by one.
• Another way to increase the time or date, is to press the right SEEK arrow or FWD button.
• To decrease the time or date, press the left SEEK arrow or REV button, or turn the knob, located on the upper right side of the radio.
The date does not automatically display. To see the date press the button while the radio is on. The date with display times out after a few seconds and goes back to the normal radio and time display.

Hope this helps ! hope you had a very Merry Christmas an have Happy New Year

Hi.

Here the relevant extract from owners manual.

To reset the hour: Push the "MODE" button until the hour display appears and blinks. Then push the "RESET/ADJ" button.
To reset the minutes: Push the "MODE" button until the minute display appears and blinks. Then push the "RESET/ADJ" button.
After resetting the clock, push the "MODE" button until the display returns to normal calendar mode.

Register for free here to get the online support: 2004 Toyota Avalon Owners Manual FREE

Regards.

Ginko

Set the display window to ODO.
Turn the ignition switch off.
While pressing the reset switch, turn the ignition switch on(IG). Keep pressing the reset switch for at least 5 seconds to complete reset procedure.

*IF this does not work you have be confused with the warning light, it may not be the oil life, but check engine light, refer to owners manual for clarity.

Setting the Clock Without Date Display AM/FM Base Radio with a Single CD Player
To set the time:

1. Turn the ignition key to ACC/ACCESSORY or ON/RUN. Press to turn the radio on.
2. Press until the hour begins flashing on the display. Press a second time and the minute begins flashing on the display.
3. While either the hour or the minute numbers are flashing, turn to increase or decrease the time.
4. Press again until the clock display stops flashing to set the currently displayed time; otherwise, the flashing stops after five seconds and the current time displayed is automatically set.

To change the time default setting from 12 hour to 24 hour, press the button until 12H or 24H is displayed. Once 12H or 24H is displayed, turn the knob to the desired option to select the setting. Press the button again to apply the setting, or let the screen time out.
With Date Display Radio with CD (MP3) and USB Port, and Radio with Single CD (MP3) Player
To set the time and date:

1. Turn the ignition key to ACC/ACCESSORY or ON/RUN. Press to turn the radio on.
2. Press and the HR, MIN, MM, DD, YYYY (hour, minute, month, day, and year) displays.
3. Press the softkey located below any one of the tabs that you want to change.
4. To increase the time or date do one of the following: • Press the softkey located below the selected tab. • Press SEEK, or FWD. • Turn clockwise.
5. To decrease the time or date do one of the following: • Press SEEK or REV. • Turn counterclockwise.

The date does not automatically display. To see the date press while the radio is on. The date with display times out after a few seconds and goes back to the normal radio and time display.
To change the time default setting from 12 hour to 24 hour or to change the date default setting from month/day/year to day/month/year:

1. Press and then the softkey located below the forward arrow label. Once the time 12H and 24H, and the date MM/DD/YYYY (month, day, and year) and DD/MM/YYYY (day, month, and year) displays.
2. Press the softkey located below the desired option.
3. Press again to apply the selected default, or let the screen time out.

1. T-BELT MODE DISPLAY
a) With ignition turned ON, using the trip switch (select/reset button) change the display to ODO, and turn the ignition OFF
b) While pressing the trip switch, turn the ignition switch ON and hold it for 5 seconds.
c) Release the trip switch, then press the switch again within 5 seconds.
d) The digital display should change to T-belt mode. The initial display "15" (0,000km) is displayed (ie. 150,000km).

2. REWRITING REPLACEMENT VALUES
While in the T-Belt mode, each press of the trip switch will change the displayed value by 10,000km increments. Once " 20 " (200,000km) is reached the display reverts back to " 1 " (10,000km) again. Remember, this setting is the number of kilometres to be travelled before the light comes on next, and once reset this counter will start from zero.
I believe the timing belt interval for all the 100 series engine variants is 150,000km, but this should be checked against each different markets servicing recommendation. This being the case, you shouldn't need to change from the default setting of "15".
Obviously for the US, the ODO is in miles, and I guess the T-Belt warning would be set in 10,000 mile intervals.

3. T-BELT WARNING RESET COMPLETION
a) After setting the replacement setting value, hold the trip switch ON for more than 5 seconds then release the switch.
b) Check that the display has now changed back to ODO and that the warning light has gone off when the engine is started.
NOTE: If the T-Belt mode is completed, even though the belt replacement has not been performed, the T-Belt warning IS reset.

SWITCH IGNITION ON WITH ENGINE OFF.PRESS SMALL ROUND BUTTON ON LOWER RIGHT OF THE SPEEDOMETER UNTIL IT DISPLAY ODOMETER.THEN TURN OFF IGNITION SWITCH OFF.PRESS AND HOLD SAME ROUND BUTTON LOWER RIGHT SPEEDOMETER TURN IGNITION TO ON WITH ENGINE OFF.CONTINUE TO HOLD BUTTON FOR AT LEAST 5 SECONDS UNTIL IT DISPLAY INDICATES 000000 AND MAINT REQUIRED LAMP WILL EXTINGUISH.RESETTING IS COMPLETE.

Pontiac Aztek, Montana 2001-05 w/o (DIC) Driver Information Center; Torrent, Ascender 2006

Turn the ignition to ON, with the engine off. Fully depress and release the accelerator pedal slowly three times within five seconds. Turn the key to OFF If the CHANGE ENGINE OIL’ message comes back on when you start your vehicle, the engine oil life system has not reset. Repeat the procedure.

Pontiac Aztek, Montana 2001-06 wI (DIC) Driver Information Center

urn the ignition to ON, with the engine off. Press the MODE button until the DIC reads ‘OIL LIFE LEFT/HOLD SET TO RESET Press and hold the SET button until 100% is displayed. You will hear three chimes and the “CHANGE ENGINE OIL” message will go off. Turn the key to OFF. If the “CHANGE ENGINE OIL” message comes back on when you start your vehicle, the engine oil life system has not reset. Repeat the procedure.

Good luck

CHANGE THE FUEL FILTER, AIR FILTER

Turn the key to ON, put your foot on the brake and move shifter to N. Try and start it. If nothing then you probably have a bad starter.