Question about 2009 Chrysler Sebring

2 Answers

WHAT DOSE THE CODE P0335 AND P0315 MEAN - 2009 Chrysler Sebring

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 14,092 Answers

CODE PO335 CRANKSHAFT POSITION SENSOR CIRCUIT. CODE PO315 - NO CRANKSHAFT POSITION SENSOR LEARNED. POSSIBLE CAUSES, CRANKSHAFT TONE WHEEL FLEX PLATE IS DAMAGED, TONE WHEEL PULSE RING MAY BE DAMAGED, ERRATIC CKP SENSOR SIGNALS WIRING CONNECTOR PROBLEM, CKP SENSOR HAS FAILED, PCM HAS FAILED.

Posted on Jul 01, 2011

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Chrysler Master
  • 1,049 Answers

This is an obd2 trouble code table, it can help you understand the meaning of code.

Posted on Jul 01, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

P0315 hammer h3 2006


DTC P0315 Crankshaft Position (CKP) System Variation Not Learned
The crankshaft position (CKP) system variation learn feature is used to calculate reference period errors caused by slight tolerance variations in the crankshaft, and the crankshaft position sensors. The calculated error allows the powertrain control module (PCM) to accurately compensate for reference period variations. This enhances the ability of the PCM to detect misfire events over a wider range of engine speed and load. The PCM stores the crankshaft position system variation values after a learn procedure has been performed. If the actual crankshaft position variation is not within the crankshaft position system variation compensating values stored in the PCM, DTC P0300 may set. If the PCM detects the CKP system variation values are not stored in the PCM memory, DTC P0315 sets.
you need a factory scan tool to do the variation relearn .
Install a scan tool.
Monitor the engine control module (ECM) for DTCs with a scan tool. If other DTCs are set, except DTC P0315, refer to Diagnostic Trouble Code (DTC) List - Vehicle for the applicable DTC that set.
With a scan tool, select the CKP system variation learn procedure and perform the following:
3.1. Observe the fuel cut-off for the applicable engine.
3.2. Block the drive wheels.
3.3. Set the parking brake.
3.4. Place the vehicle's transmission in Park or Neutral.
3.5. Turn the air conditioning (A/C) OFF.
3.6. Cycle the ignition from OFF to ON.
3.7. Apply and hold the brake pedal for the duration of the procedure.
3.8. Start and idle the engine.
3.9. Accelerate to wide open throttle (WOT). The engine should not accelerate beyond the calibrated fuel cut-off RPM value noted in step 3.1. Release the throttle immediately if the value is exceeded.

Important: While the learn procedure is in progress, release the throttle immediately when the engine starts to decelerate. The engine control is returned to the operator and the engine responds to throttle position after the learn procedure is complete.
3.10. Release the throttle when fuel cut-off occurs.
The scan tool displays Learn Status: Learned this Ignition. If the scan tool indicates that DTC P0315 ran and passed, the CKP variation learn procedure is complete. If the scan tool indicates DTC P0315 failed or did not run, refer to DTC P0315 . If any other DTCs set, refer to Diagnostic Trouble Code (DTC) List - Vehicle for the applicable DTC that set.
Turn OFF the ignition for 30 seconds after the learn procedure is completed successfully.

Did you replace the crank sensor ?

Dec 26, 2016 | Cars & Trucks

1 Answer

What does obd2 code Po315 Crankshaft Position System Variation Not Learned mean?


you can read through the suggested answers and you can read through this discussion to get insight into the problem. Dodge Codes P0315 and P0339

Jan 27, 2015 | Cars & Trucks

1 Answer

P0315


What repairs were done on the vehicle lately? This is a crankshaft positioned sensor code. If no one went near the sensor, the wiring, trigger wheel, connector, or sensor could be bad. Easiest fix: change the sensor. Right fix: check out the items I mentioned above before spending any money.

Mar 25, 2014 | 2007 Chevrolet Cobalt Coupe

1 Answer

2005 Dodge Neon SXT 2.0L crankshaft position sensor location to replace


P0315 - Crankshaft Position System Variation Not Learned
P0335 - Magnetic Crankshaft Position Sensor Electrical Error China OBD2 car diagnostic tools wholesale on CareUCar

Mar 20, 2014 | 2005 Dodge Neon SXT

1 Answer

What does trouble code P0315 on a 2006 Pontiac Grand Prix mean?


P0315 is a code that indicates and error from the crankshaft position sensor. Typically it is the sensor itself and not an issue with the crankshaft. The sensor itself runs from $30 to $40, but replacement may not be a DIY job unless you're comfortable under a car and removing pulleys from the front of the engine.

Mar 17, 2014 | Pontiac Grand Prix Cars & Trucks

1 Answer

Obd2 code P0335 crank position sensor replaced twice but light is still on how to turn off lighr


Just because you replaced a sensor doesn't mean you repaired the problem. To make sure, have the code cleared and if it comes back, you haven't found your problem yet. Having the code doesn't automatically mean the sensor is the cause. It can be anything in the circuit or even a mechanical issue.

Aug 14, 2013 | 1997 Mazda 626

1 Answer

2005 CHRYSLER SEBRING P0315


Well the code p0300 is a mis fire code the 315 is I believe a cam timing code which can cause the 300 replace the cam trimming actuator, it should fix ur problem.

Jul 29, 2012 | 2005 Chrysler Sebring Sedan

1 Answer

P0335


Hi, you can fix it by reading the article found here on P0335 - http://www.obd-codes.com/p0335

Mar 29, 2009 | 2003 Mazda Mazda6

Not finding what you are looking for?
2009 Chrysler Sebring Logo

1,268 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

Marvin
Marvin

Level 3 Expert

85160 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...