CHRYSLER CAR STEREO CODES
https://www.carstereocode.com/unlock.php?mk=8
Unfortunately Chrysler radio codes are not available anywhere for free on the Net. However, you can get the correct code for your Chrysler car or Jeep at this site.
Cheapest anywhere on the Net by far.
http://unlockmyradio.weebly.com/chrysler-radio-codes.html
As these are an anti-theft radio you will have to go to the dealer and have them get the code for you.find out the input sequence so you can do it if it happens again and write both down so you will have it,this will happen if the battery goes bad also.
SOURCE: diagnostic Troubleshooting Codes for 1996 Chrysler Sebring Cvtble
FIRST YOU TURN IGNITION SWITCH ON WITH ENGINE OFF.LOOK AT MIL LIGHT IT SHOULD COME ON 3 SECONDS THEN GO OFF IT NOT THEN YOU GOT BURN OUT BULB OR A CIRCUIT PROBLEM.IF ALL IS WELL. ATTEMPT TO START ENGINE.TURN OFF IGNITION. WITH OUT STARTING ENGINE.TURN IGNITION ON OFF ON OFF AND WITHIN 5 SECONDS RECORD 2 DIGIT DIAGNOSTIC TROUBLE CODES.DISPLAYED BY FLASHING MIL LIGHT.YOUR MIL FLASHES WILL BE YOUR CODE LIKE THE MIL LIGHT FLASHES 5 TIMES THEN PAUSE FLASHES 3 TIMES THAT CODE 53 THAT YOUR CODE.IT LIKE MORSE CODE.WHEN DONE TURN OFF IGNITION SWITCH.GO TO AUTO ZONE OR ADVANCE AUTO GET HAYNES COMPUTER CODE BOOK. TO GET CODE MEANING OR WHAT SENSOR GONE BAD.HOPE THIS CAN BE SOME HELP.
SOURCE: Second key and fob for 2005 Chrysler Sebring Convertible
go to your dealer. It will cost you an arm and a leg for the key and fob and also to program it.
SOURCE: I HAVE A 2005 CHRYSLER SEBRING AND DOME LIGHT,RADIO ALL POWER LOCKS HAVE QUIT WORKING
me too! - looking at fuse #5 red 10 Amp one but has black thing on it.
Can't get if off..
Have read the manual is wrong and to use panel on side of fuse box for fuse locations...
SOURCE: how do you change the battery for a 2005 chrysler serbring
Battery is behind the tire. You have to remove the tire to get to the battery.
First of all you DO NOT have to remove the tire...you turn your wheels hard right, this will give you plenty of room to get to the battery. Remove the wheel well plate and you will see the battery just in from of where the tire would normally be pointing. From there it's pretty straight forward.
SOURCE: I need a timing belt diagram for a 2005 chrysler sebring
My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.
I have only been a free contributor to this site for the past 4-months.
I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.
CLICK on the following LINK. It has the Belt Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my apologies...
http://www.2carpros.com/car_repair_information/year/2005/make/chrysler/model/sebring/2005_chrysler_sebring_timing_belt_diagram_marks.htm
No Camshaft Position Sensor Circuit Failure
Possible Causes:
CMP Sensor connector is damaged, open or it is shortedCMP Sensor signal circuit is open or shorted to ground or to battery voltage or 5v supply circuitCMP Sensor 5v supply circuit is open or shorted to ground or to battery voltageCMP Sensor ground circuit is openCMP Sensor is damaged or has failedCKP Sensor is damaged or has failedPCM has failed.Here's a link to your sensor.
1,208 views
Usually answered in minutes!
×