How to rebuilt the cylinder head of daihatsu charade 3 cylinder engine

Yes certainly can and the Service Manual as well

VALVE CLEARANCE (K3-VE)

VALVULITA https://www.valvulita.com > sites > default > files
(u) Apply engine oil to the cam of the camshaft and the journal part of the cylinder head, and then install the camshaft. NOTICE: Position it so the cam nose of ...
10 pages

Daihatsu TERIOS J100 Maintenance Manual (Page 18 of 43)

ManualsLib https://www.manualslib.com > ... > Maintenance manual
Inspection and adjustment of valve clearance. The measurement and adjustment ... apply engine oil to between the lock nut and the valve. rocker arm. q Remove ...

Tappet clearance 1300cc terios?

Fixya https://www.fixya.com > ... > Daihatsu > Terios
Nov 14, 2019 - The tappet clearance for your Hyundai Atos 2007 would be: ... Valve clearance Warm: 0.2 mm intake, 0.25 mm exhaust. ... Valve clearance Cold: 0.1 mm intake, 0.17 mm ...

I need valve clearance for Daihatsu Terios HC-EJ - Fixya
Jan 21, 2012
How do I set the valve clearances on a Daihatsu Terios 2001
Mar 1, 2015
Valve clearance and procedure for 1.2 Hc-Ej terios engine.it
Jun 3, 2014
Valve clearance for Daihatsu Terios - Fixya
Mar 20, 2012
More results from www.fixya.com

DeVille, Eldorado, Seville 1999-2005

• REMOVAL & INSTALLATION

Cylinder Head

Print

Removal & Installation

Left Side

1. Before servicing the vehicle, refer to the Precautions Section.
2. Drain the cooling system.
3. Properly relieve the fuel system pressure.
4. Remove or disconnect the following:
   
   Negative battery cable Exhaust manifold Alternator Water crossover Intake manifold Valve cover Timing cover Secondary camshaft drive chain Power steering return hose retaining bolt from the cylinder head 3 M6 external drive bolts from the front portion of the cylinder head 10 M11 internal drive cylinder head bolts Cylinder head and gasket.
   
5. Clean the head mating surfaces.

To install:

Fig. Left cylinder head bolt torque sequence-4.6L engine

1. Install the cylinder head with a new gasket. Lubricate the bolts with engine oil prior to installation.
2. Torque the M11 bolts in sequence as follows:
   1. Step 1: 30 ft. lbs. (40 Nm), plus an additional 70 degrees
   2. Step 2: Turn an additional 60 degrees
   3. Step 3: Turn an additional 60 degrees (total 190 degrees)
   
   
3. Torque the M6 bolts to 106 inch lbs. (12 Nm)
4. Install or connect the following:
   
   Power steering return hose retaining bolt to the cylinder head and tighten to 37 ft. lbs. (50 Nm) Secondary camshaft drive chain Timing cover Valve cover Intake manifold Water crossover Exhaust manifold Negative battery cable
   
5. Change the oil and filter.
6. Fill the cooling system.

Right Side

1. Before servicing the vehicle, refer to the Precautions Section.
2. Drain the cooling system.
3. Properly relieve the fuel system pressure.
4. Remove or disconnect the following:
   
   Negative battery cable Exhaust manifold Water crossover Intake manifold Valve cover Timing cover Secondary camshaft drive chain Electrical connector from the Engine Coolant Temperature (ECT) sensor Nut attaching the coil cassette ground wire to the cylinder head Bolt attaching the exhaust crossover pipe to the cylinder head Bolt attaching the right transaxle mount bracket to the cylinder head Bolt attaching the rear transaxle brace to the transaxle Nuts attaching the rear transaxle brace to the cylinder head Rear transaxle brace 3 M6 external drive bolts from the front portion of the cylinder head 10 M11 internal drive cylinder head bolts Cylinder head and gasket
   
5. Clean the head mating surfaces.

To install:

Fig. Right cylinder head bolt torque sequence- 4.6L engine

1. Install the cylinder head with a new gasket. Lubricate the bolts with engine oil prior to installation.
2. Torque the M11 bolts in sequence as follows:
   1. Step 1: 30 ft. lbs. (40 Nm), plus an additional 70 degrees.
   2. Step 2: Turn an additional 60 degrees.
   3. Step 3: Turn an additional 60 degrees (total 190 degrees).
   
   
3. Torque the M6 bolts to 106 inch lbs. (12 Nm).
4. Install or connect the following:
   
   Rear transaxle brace over the studs located at the rear of the right cylinder head Nuts attaching the rear transaxle brace to the cylinder head, loosely Bolts attaching the rear transaxle braces to the transaxle and tighten to 37 ft. lbs. (50 Nm) Nuts attaching the rear transaxle brace to the cylinder head and tighten 37 ft. lbs. (50 Nm) Electrical connector to the ECT sensor Bolt attaching the exhaust crossover pipe to the cylinder head and tighten to 18 ft. lbs. (25 Nm) Nut attaching the coil cassette ground wire to the cylinder head and tighten to 13 ft. lbs. (17 Nm) Secondary camshaft drive chain Timing cover Valve cover Intake manifold Water crossover Exhaust manifold Negative battery cable
   
5. Change the oil and filter.
6. Fill the cooling system.

I have just rebuilt one for our Westerly 21. This is from my Petter 'A' range workshop manual:-
The water cooled engines (AC1W etc.) are:cylinder head nuts: 30NM (22 lbft) except 32.5NM (24 lbft) for the one that also holds the rocker.
Valve clearances are 0.1mm (0.004") COLDReset valve clearance after one hours running since torquing the head.
Retorque head and set valve clearance after initial 20 hours running
I believe Mini-6 refers to the water cooled engines but just in case, the air cooled engines are 27N (20 lbft)

head torque is in 3 parts....
stage1....... 20nm
stage2........40nm
and stage3 .......49 to 59 nm so anywher in middle

valve clearance inlet 0.25mm hot
and outlet 0.33mm hot

hope this helps and if need anymore tech data just let me know and ill try and sort it for you
please leave a comment and a thumbs up.... cheers

not a problem as these little cars are very forgiving ,head bolts 65nm camshaft cap 12nm camshaft sprocket 22nm ,

40 to 47 ft-lbs, or 6.5 kg-m

Ignition timing should be checked and adjusted whenever spark plugs are replaced or any distributor maintenance is performed. Ignition timing at 1000 RPM or less should be as follows: on 1989 1.3L/4-79 engines, 3-7°BTDC; on 1990-92 1.3L/4-79 engines, 0-2°; on 1.6L/4-97 engines, 1-5°.

here

If you have oil in the water it smacks of a problems with the gasket or a crack in the head. Did you tension the head with a torque wrench? Did you retension after the first drive, with engine cool? What do the spark plugs look like?

Did you adjust the ignition timing after replacing the points?

you will need a manual for this as diesel torque settings are different to that of a petrol engine.