LOCATION FOR WARNING FLASHER - Montero Sport Mitsubishi Cars & Trucks

Doesn't exist as written.

https://www.google.com/search?q=2006+100+series+1hzj100

Question should state 'year make model (diesel).

Everything is available on Google

year make model diesel hazard warning relay location

BUT, you will probably find that there isn't one and it is a function of the Body Control Module.

Flasher/Turn signal Relay is part of the Hazard warning switch.
Remove Instrument panel Trim. Then Remove the hazard warning switch from the center air outlet.


I’m happy to assist further over the phone at https://www.6ya.com/expert/uttamjeet_2f3adc18600f8ede

The Hazard Warning flasher switch is located in the center of the instrument panel above the radio. Press the switch to turn on the Hazard Warning flasher. When the switch is activated, all directional turn signals will flash on and off to warn oncoming traffic of an emergency. Press the switch a second time to turn off the Hazard Warning flasher. This is an emergency warning system and should not be used when the vehicle is in motion. Use it when your vehicle is disabled and is creating a safety hazard for other motorists. When you must leave the vehicle to seek assistance, the Hazard Warning flasher will continue to operate even though the ignition switch is OFF. NOTE: With extended use, the Hazard Warning flasher may wear down your battery. http://cdn.dealereprocess.com/cdn/servicemanuals/chrysler/2010-townandcountry.pdf

Flasher units are sometimes fitted in the steering column cowling and sometimes not far away from the hazard warning light switch. I have also known them to be behind the instrument panel.

Some manufacturers like the clicking sound to be heard and others don't care. When the flasher unit is buried deep somewhere some have even fitted a clicking device to reassure the driver.

Sorry I can't help further.

just change the flasher relay .

Replacement The turn and hazard flashers are integrated into one flasher on these models. The flasher is located in the hazard warning switch and the hazard warning switch is located on the trim plate. Replace the flasher by unplugging the old one, removing it from the panel, and plugging in the new one.

1. Remove the bezel from the ignition switch.
   

Remove the bezel from the ignition switch

Carefully remove the instrument panel accessory trim plate.


To remove the trim plate, use a suitable prytool to carefully apply pressure at the retaining clip points . . .


. . . then gently pull the accessory trim plate away

Detach the electrical connector from the hazard warning switch.


Unplug the electrical connector from the hazard warning switch . . .

Unfasten the screw securing the hazard warning switch and remove the switch.


. . . then unfasten the screw securing the hazard warning switch and remove the switch from the vehicle


Installation is the reverse of removal.

here is the location of the flasher The Turn Signal and Hazard Warning Flasher is combined into one unit called a Combination Flasher (Combo-Flasher) The combo-flasher controls the flashing of the hazard warning system and the turn signal system. An inoperative bulb or incomplete turn signal circuit will result in an increase in flasher speed.
The combo-flasher is mounted to the in-line bracket which is located to the right of the Junction Block. The flasher can be removed by pulling in an rearward direction. The left under panel silencer duct must be removed to access the flasher. The combo-flasher is black in color for ease of identification

COMBINATION FLASHER LOCATION The Turn Signal and Hazard Warning Flasher is combined into one unit called a Combination Flasher (Combo-Flasher) The combo-flasher controls the flashing of the hazard warning system and the turn signal system. An inoperative bulb or incomplete turn signal circuit will result in an increase in flasher speed.
The combo-flasher is mounted to the in-line bracket which is located to the right of the Junction Block. The flasher can be removed by pulling in an rearward direction. The left under panel silencer duct must be removed to access the flasher. The combo-flasher is black in color for ease of identification

Fuses are located in the junction box below the instrument panel to the left of the steering column. The turn signal flasher and hazard warning flasher also plug into the fuse block. Each fuse receptacle is marked as to the circuit it protects and the correct amperage of the fuse. In line fuses are also used. Refer to the Fuse Chart at the end of the information for their location. The fuse block on some models is a swing-down unit located in the underside of the instrument panel adjacent to the steering column. Access to the fuse block on some models is gained through the glove box opening. The Convenience Center on some models is a swing-down unit located on the underside of the instrument panel. The swing-down feature provides central location and easy access to buzzers, relays and flasher units. All units are serviced by plug-in replacement. Location of Convenience Center on specific models may vary.

the hazard warning lights fuse is in the under hood fuse box. Its a 15A and should be listed as No. 5 in your owner's manual. If you look at your fuse box from the front, it would be in the top row of small fuses on the left side of the box---the farthest fuse on the right.