Key phob does not work and it says on the dash engine disabled press key fob or enter code. require code

Check the battery... sounds like its dead.

Alarm System Operation & Diagnosis - Range Rovers

www.rangerovers.net/repairdetails/becm/alarm.html

(If done by the key, a press on the remote locking button is still required before .... the BeCM goes into a 10 minute lockout mode (30 minutes for 1996 and later ..... buttons at the dealership, you may need to reset the code on the fob - which is ...

How to reset the security lockout on a Saturn Vue

www.kittycatonline.com/.../How-to-reset-the-security-lockout-on-a-Satur...

Nov 30, 2014 - How to reset the security lockout on a Saturn Vue. ... Now, though, not only does the "phone start" system still fail to function, the remote start fob now fails to work as well. ... the Passlock system starts out in what I'll call "agressive" mode. ... basically disabling it: Get the original factory remote unlock key fob, ...

When replacing the key fob battery there is no reprogramming required! If the key fob was working prior to the battery replacement then it would point to the contacts not being correct! Remove key fob battery and start again!

You have to have a key fob (unless your car has a number key pad on the door that allows you to put in a code). You could also posssibly hit the lock button on the inside of the door then close the door (but if you don't have a key fob you will not be able to get back in the car!).

It could be dirty terminals in the key fob, also make sure the battery is the correct way round, positive facing up, hope this helps.

If you lock your doors with the remote, you have to use the remote to unlock them or it set off the alarm. I don't know why the manufacturers designed it that way(kind of stupid)but it's programmed into the on board computer. You can't disable the alarm without creating a worse problem somewhere else.

The BECM will retain the EKA code, so , charge or replace the battery. Close all doors, windows bonnet etc, then try the EKA code. You must know, that if you enter the incorrect code or do not enter the code correctly by returning the key to the centre position after each turn of the key , more than 3 times, then the system will lock out and you will have to wait 30 minutes to retry. It should start , but it would be good to get another remote handset, Hope that helps

You should not have to reset the key fob after a battery replacement. The signal from the key fob stays the same and is programed to the reciever.
If the key fob needs to be reprogrammed then follow these steps.
1. Have all key fobs with you during programming.
2. Sit in the vehicle with all doors closed.
3. Lock all doors using the Lock/Unlock switch on the door.
4. Insert and withdraw the ignition key 7 to 9 times within 10 seconds (do not turn the key, just insert and withdraw).
5. The 4 way flasher indicator on the dash should flash once or twice.
6. Insert the ignition key and turn it on (key on, engine off).
7. Press any button on one remote and the 4 way flasher indicator on the dash should flash once.
8. If you have more key fobs to program use the Lock/Unlock button on the door to unlock the doors and then lock the doors.
9. Press any button on the next key fob and the 4 way flasher indicator on the dash should flash once.
10. Repeat if you have more key fobs. Only 5 can be programmed.
11. To exit, simply turn of the igniton and remove the ignition key.
12. Unlock the doors using the Lock/Unlock switch on the door and exit the vehicle.
13. Make sure the window is down when testing remotes in case you leave the keys inside.
14. Close all doors and test all remotes that were programmed.

Do not skip any steps or the process will not work.

If the 4 way flasher indicator does not work when inserting the key, you will need to start the process from the begining. If it still does not work the receiver may be your problem.

If the 4 way flasher indicator does not flash when pressing any button on the key fob then the key fob is the problem (dead battery or defective remote)

Immobilizer system can be disarmed using 4 digit code from vehicle security card as detailed in owners handbook.

If you don't have one that works for the vehicle now, you'll have to take it to your local dealer to have it programmed to the vehicle. Some will charge for this, some will do it at no charge.

If you do have a remote that is programmed and working for the vehicle, then the following steps will allow you to program another remote:

1. Enter vehicle and close all doors.

2. Put seatbelt on (or clip it into the buckle) to shut the warning buzzer off.

3. Put key in ignition, turn to run position but don't start it.

4. Press and hold the unlock button on the working key fob and hold for 4 seconds, then also press the panic button.

5. Release both buttons and you should hear a single chime to indicate it is in program mode. You have 30 seconds after the chime to program any additional remotes you want to program.

6. Press and release both the unlock and lock buttons simultaneously on the remote you are programming. You should hear another single chime.

7. Within 4 seconds after hearing the chime, press either lock or unlock button on remote that you are programming.