I have a scan tool that says my egr valve system not ready on my Ford f150 5.4 and my catylist reads not ready how can I fix this problem

Question 1

2helpful

3answers

2002 Chevy replaced Egr valve and oxygen sensor 2says not ready for Egr and evap

Replacing parts on the chance of solving the problem can get expensive. Take it to someone who has a scanner tool to check the sensors. Sound like you have a sensor not working.

Jun 18, 2014 • 2002 Chevrolet Impala

0helpful

2answers

Idle is rough

Spark Plugs have to be changed every 3 years
Front Oxygen Sensors changed every 100,000 miles
Can't have any Vacuum Leaks -- anywhere on the vehicle
Need to have it road tested with a Professional Scan Tool
& look at all data & get caught up on Preventative Maintenance
Very few people change motor oil 3 or 4 times a year, if at all,
and the Variable Cam Actuators fail, as a result,that & few other
things can cause rough running engine & resulting idle issues
It's well known that Ford COP Ignition Coils fail sometime in
every year of ownership

Jun 21, 2013 • 2003 Ford Explorer

0helpful

1answer

I have a 1998 ford escort with a check engine light on and can't get it off

Here is a list of possible causes. Some things you have already done.

EGR solenoid valve harness is open or shorted
- EGR solenoid valve circuit poor electrical connection
- EGR volume control valve stuck closed
- Faulty EGR Pressure sensor
- Faulty EGR temperature sensor and circuit
- Faulty EGR Valve
- EGR passage clogged
- Exhaust gas leaks
Read more: http://engine-codes.com/p0401_ford.html#ixzz28fATCih2

Oct 07, 2012 • 1998 Ford Escort

1helpful

1answer

Code 1404 on 01 malibu

The Powertrain Control Module (PCM) monitors the Exhaust Gas Recirculation (EGR) valve pintle position input to ensure that the valve responds properly to commands from the PCM. When the ignition switch is turned ON, the PCM learns the EGR learned minimum position. The PCM compares the EGR learned minimum position to the EGR position sensor when the EGR valve is commanded closed. If the EGR position sensor indicates that the EGR valve is still open when the PCM is commanding the EGR valve closed, this DTC will set.

A scan tool that is capable of commanding the EGR circuits on and off is required to verify EGR performance and sensor feedback voltages at the PCM. However, this code is USUALLY caused by carbon getting stuck in the EGR pintle and holding it open. A good cleaning is usually all that is required to fix this.

You will need an EGR gasket. Remove the EGR valve and inspect the ports for heavy carbon deposits. These deposits can usually be cleaned out using screwdrivers and a piece of mechanics wire to break the carbon loose and some carb and choke cleaner to finish the clean-up. A wire brush and some carb cleaner usually works for the EGR valve itself. Once the ports and the valve are clean, re-install the valve using the new gasket. Clear the codes and drive the vehicle to see if the problem is fixed. Please note that the EGR monitor runs at speeds over 50 Mph. during deceleration, so you need to get the vehicle on the highway for a valid test of the EGR system.

If the Check Engine light does not come on during the road test, Connect a code reader and check the OBD readiness monitors. If the EGR monitor says "complete" and there are no codes in the computer, then you have done a successful repair.

Aug 04, 2011 • Chevrolet Malibu Cars & Trucks

0helpful

1answer

Erg code 405 how do test it

Potential causes of a P0405 code include:
Short to ground in EGR signal or Reference circuits
Short to voltage in EGR ground or signal circuits
Bad EGR valve
Bad PCM wiring issues due to chafing or loose terminals

Possible Solutions:
If you have access to a scan tool you can command the EGR valve on. If it responds and the feedback indicates the valve is moving properly then the problem may be intermittent. Sometimes in cold weather, moisture can freeze in the valve causing it to stick. After the vehicle warms up the problem may disappear. Carbon or other debris can lodge in a valve causing it to stick also

If the EGR valve doesn't respond to your commands with the scan tool, disconnect the EGR harness connector. Turn the key to on position, engine off (KOEO). Using a voltmeter, check for 5 volts on the reference wire to the EGR valve. If there is no 5 volts, is there any voltage at all? If there is 12 volts, then repair short to voltage in the 5 volt reference circuit. If there is no voltage connect a test light to battery voltage and probe the 5 volt reference wire. If the test light illuminates, the 5 volt reference circuit is shorted to ground. Repair as necessary. If the test light doesn't illuminate check for an open in the 5 volt reference circuit. Repair as necessary

If there is no apparent problem and there is no 5 volt reference, PCM may be at fault, however other codes will likely be present. If 5 volts are present on the reference circuit, jumper the 5 volts to the EGR signal circuit. Now the EGR position on the scan tool should read 100 percent. If it doesn't connect test light to battery voltage and probe the EGR signal circuit. If it illuminates, then the signal circuit is shorted to ground. Repair as necessary. If the light doesn't illuminate, check for an open on the EGR signal circuit. Repair as necessary.

If, after jumpering the 5 volt reference circuit to the EGR signal circuit the scan tool EGR position reads 100 percent, then check for poor terminal tension at the EGR valve connector. If the wiring is okay, replace the EGR valve.

Hope this helps.

Jun 24, 2011 • Chevrolet S 10 Cars & Trucks

3helpful

1answer

I replaced egr valve code 401 still comes up on my scanner. why?

The code P0401 is often not a problem with the EGR valve itself. Rather, the EGR system is not allowing enough EGR to flow back into the combustion process to sufficiently cool the peak firing temperatures. Once the code P401 has been retrieved with a scan tool, the freeze frame data should be documented and analyzed in order to determine what engine conditions were present when the code was triggered. It is recommended that the vehicle be driven in such a way as to duplicate the code setting conditions with a data streaming scan tool connected, so the behavior of the EGR actuating components and feedback sensors can be monitored.
Common Tests to Determine Whether the Problem Is an EGR Control Problem, a Plugged or Restricted System, or a Defective Feedback Device

Does the engine die, not just stumble, when the EGR valve is manually raised to its maximum?
(Use either a vacuum pump or bi-directional scan tool if it's a digital EGR valve.)
Is the EGR valve getting sufficient vacuum? (Use the manufacturer EGR vacuum spec.)
Is the EGR system restricted? (The engine stumbles, but does not die.)
Is the EGR system plugged? (Engine RPM does not change.)
Does the EGR valve work?
Raise the RPM to 3000 and check manifold vacuum. Then open the EGR valve to its maximum-the manifold vacuum should drop by at least 3" of mercury. If it does not, there is a flow and/or restriction problem.
Test the EGR temperature sensor (if equipped) with a propane torch and a DVOM.
Test the accuracy of the EGR valve position sensor with a scan tool or DVOM by raising or lowering the EGR valve.
Test the Digital EGR Pressure Feedback Sensor (DPFE) with a data streaming scan tool to verify that the voltage or lift percentage changes according to spec.
Verify that the front Oxygen Sensor readings drop and the Short Term Fuel Trim increases when the EGR valve opens. (EGR leans out the mixture.)

Mar 29, 2011 • 2000 Pontiac Grand Am GT

2helpful

2answers

Aside from the P0406 code, I'm also getting code P1561. Are they related and what can I do to fix it? I have 2006 Dodge Ram 1500.

The po406 is an egr code which is common for a bad egr valve, but check your wiring and check for plugged port or carbon lodged in valve, as far as the p1561 this is not a good code, this must of been gotten with a genric scan tool, i would fix the po406 and then reset the computer readiness monitors and drive it and go from there. hope this helps, good luck

Jan 10, 2011 • 2006 Dodge Ram 1500

2helpful

1answer

Code definition: EGR valve has excessive circulation. Do I change the valve? Awaiting your reply. Thanks.

No - don't change the valve. The code usually means that the DPFE (Digital Pressure Feedback EGR) sensor is indicating EGR flow when the computer is not commanding it. If you look at the EGR value on a scan tool at idle, it will read high and not change much when the EGR is manually opened. This problem is almost ALWAYS the DPFE sensor. Buy one from Ford. The aftermarket ones are junk and don't hold up. You can spend $60 on the part or you can spend $100 on the diagnosis to find out what's wrong. It's worth it to try the part in this case. You will need to clear the code. You should be able to disconnect the battery cables for 30 minutes to clear the code.

Aug 02, 2010 • Ford Contour Cars & Trucks

6helpful

4answers

How do I replace the EGR valve in my 1999 Ford E350 van?

Your vehicle has an EGR valve attached to the intake manifold. About how to replace an EGR Valve, check this procedure...
Parts:
1. EGR Valve

Tools:
1. Scan Tool
2. 3/8 in. Drive Ratchet
3. Wrench
4. Socket Set

Steps:
Step 1 Locate the OBD-I or OBD-II data link connector (DLC). Refer to your vehicle owner’s manual for the specific location.
o Tip: The OBD-I data link connector is usually located in the engine compartment near the battery or the fuse box. The OBD-II connector (post 1995 cars) is usually located beneath the instument panel next to the steering column.

Step 2 Turn your key to the“ON” position. Do not start the engine.

Step 3 Plug your scan tool into the DLC and follow the manufacturer's steps to read the diagnostic trouble code. Codes between P0400-P0408 are generic trouble codes for the EGR system.
o Tip: The OBD-II diagnostic trouble code (DTC) is a 5 character alphanumeric code. The first digit is a letter that indicates the component group, the second digit is OBD mandated or manufacturer specfic, the third digit is a subgroup, and the fourth and fifth digits define the component and basic problem.

Step 4 To test the EGR valve: Remove the vacuum line to the valve and install a manual vacuum pump. Start the engine and apply vacuum to the valve. If the engine idle speed drops, the EGR valve is working. If the engine idle speed does not change, the EGR system is not working. Most engines will stall if you fully open the EGR valve while idling.
o Tip: Some vehicles are equipped with electronically controlled EGR valves. Use a scan tool to test these valves.

Step 5 Remove the vacuum line or electrical connector from the EGR valve.

Step 6 Remove the EGR mounting bolts. Remove the EGR valve.

Step 7 Using a new gasket, attach the new EGR valve with the original mounting bolts. Torque the bolts to the manufacturer's specifications.

Step 8 Reconnect the vacuum line or electrical connector.

Step 9 Erase any codes on the scan tool through the“delete” or“erase” command. Remove the scan tool.

Step 10 Road test your vehicle to verify the repair.
o Tip: If the check engine light returns, repeat the diagnostic process for additional DTCs or take your vehicle to a certified repair shop.

Check the RIGHT PART before to take off the parts. Its possible that you can find few TSB in your library or dealer about this LINK.

Hope helps.

Jun 16, 2010 • Ford E-Series Cars & Trucks

8helpful

1answer

Failed Emissions test. OBD II not ready. Code for Low EGR Flow. Found EGR port clogged in intake plenum. Removed plenum and cleaned port, replaced all gaskets, check egr valve with vaccum(OK),...

Rich:

The trick to setting all the monitors is:
Make sure you have more than 1/4 tank of fuel but no more than 3/4.
Clear codes then Do Not cycle key off. Start vehicle and drive,make sure you do at least 2 minutes of steady spead between 40-50 mph and at least 2 minutes at 50-65 mph, usually about a 20 to 25 mile drive will set them..
If you turn the ignition off before the monitors complete then EVAP will have to see a 6 hour cold soak before it will attempt to run again.

Mar 24, 2009 • Mercury Sable Cars & Trucks

Question 2

ZJ Limited

Ford Master 17,989 Answers
Posted on May 22, 2011

ZJ Limited

Ford Master

Joined: Jul 15, 2008

Answers

17989

Questions

0

Helped

14453023

Points

60858

ABout EGR codes, there are alot choive to look or diagnostic... are you chec or replace the vacuum lines as well? If there is a leak, the DPFE will read incorrectly.

Did you reset the PCM or disconnect the battery after the repair? Assuming all fuses are good, the P1401 indicates a possible wiring fault. Check the connector. Is it clean? Is it pushed in all the way? Are the wires in good condition?

Since the DPFE has been replaced, likely there is a restriction in the EGR line some where. This could also be a bad EGR valve. But first ensure that the EGR valve vacuum line is attached and leak free.

If no problem found, then the EGR passageways in the throttle body should be cleaned. Carbon will build up and block the EGR flow.

If still no problem found, consider replacing the EGR valve.

Keep in mind this information from Ford Service CD...

P0401 - EGR Flow Insufficient Detected
The EGR system is monitored during steady state driving conditions while the EGR is commanded on. The test fails when the signal from the DPF EGR sensor indicates that EGR flow is less than the desired minimum.
Vacuum supply
EGR valve stuck closed
EGR valve leaks vacuum
EGR flow path restricted
EGRVR circuit shorted to PWR
VREF open to D.P.F. EGR sensor
D.P.F. EGR sensor downstream hose off or plugged
EGRVR circuit open to PCM
VPWR open to EGRVR solenoid
D.P.F. EGR sensor hoses both off
D.P.F. EGR sensor hoses reversed
Damaged EGR orifice tube
Damaged EGRVR solenoid
Damaged PCM

Perform KOER self-test and look for DTC P1408 as an indication of a hard fault. If P1408 is not present, look for contamination, restrictions, leaks, and intermittents

P1401 - DPF EGR Sensor Circuit High Voltage Detected
The EGR monitor checks the DPF EGR sensor signal to the PCM for high voltage. The test fails when the average voltage to the PCM goes to a voltage greater than the maximum calibrated value.
DPF EGR circuit open
VREF short to PWR
Damaged DPF EGR sensor
DPFEGR circuit short to PWR
SIG RTN circuit open
Damaged PCM

A DPF EGR PID reading greater than 4.5 volts with the key ON and engine OFF or running, indicates a hard fault.

Hope this helps (remember to rate and send us your comments about this answer).

Answer 2

Anonymous

Contributor 24 Answers
Posted on May 22, 2011

Anonymous

Contributor

Joined: May 17, 2011

Answers

24

Questions

0

Helped

4876

Points

62

You must have cleared the codes.You just need to drive it about 40 or 50 miles and then let it set should fix your problem.

Related Topics:

Trustworthy Expert Solutions

I have a scan tool that says my egr valve system not ready on my Ford f150 5.4 and my catylist reads not ready how can I fix this problem

2 Answers

ZJ Limited

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

2002 Chevy replaced Egr valve and oxygen sensor 2says not ready for Egr and evap

Idle is rough

I have a 1998 ford escort with a check engine light on and can't get it off

Code 1404 on 01 malibu

Erg code 405 how do test it

I replaced egr valve code 401 still comes up on my scanner. why?

Aside from the P0406 code, I'm also getting code P1561. Are they related and what can I do to fix it? I have 2006 Dodge Ram 1500.

Code definition: EGR valve has excessive circulation. Do I change the valve? Awaiting your reply. Thanks.

How do I replace the EGR valve in my 1999 Ford E350 van?

Failed Emissions test. OBD II not ready. Code for Low EGR Flow. Found EGR port clogged in intake plenum. Removed plenum and cleaned port, replaced all gaskets, check egr valve with vaccum(OK),...

Not finding what you are looking for?

2001 F150 Styleside SuperCrew

2002 Chevy replaced Egr valve and oxygen sensor 2says not ready for Egr and evap

Ask a Question

Check Out the Latest Top Trucks Report!

Top Ford Experts

ZJ Limited

Ronny Bennett Sr.

Thomas Perkins

Are you a Ford Expert? Answer questions, earn points and help others

Manuals & User Guides

Related Topics:

Trustworthy Expert Solutions

I have a scan tool that says my egr valve system not ready on my Ford f150 5.4 and my catylist reads not ready how can I fix this problem

2 Answers

ZJ Limited

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

2002 Chevy replaced Egr valve and oxygen sensor 2says not ready for Egr and evap

Idle is rough

I have a 1998 ford escort with a check engine light on and can't get it off

Code 1404 on 01 malibu

Erg code 405 how do test it

I replaced egr valve code 401 still comes up on my scanner. why?

Aside from the P0406 code, I'm also getting code P1561. Are they related and what can I do to fix it? I have 2006 Dodge Ram 1500.

Code definition: EGR valve has excessive circulation. Do I change the valve? Awaiting your reply. Thanks.

How do I replace the EGR valve in my 1999 Ford E350 van?

Failed Emissions test. OBD II not ready. Code for Low EGR Flow. Found EGR port clogged in intake plenum. Removed plenum and cleaned port, replaced all gaskets, check egr valve with vaccum(OK),...

Not finding what you are looking for?

2001 F150 Styleside SuperCrew

2002 Chevy replaced Egr valve and oxygen sensor 2says not ready for Egr and evap

Related Topics

Ask a Question

Popular Questions

Diagram for ford f 150

Diagram of front end for '94 F150 Ford

Firing order for 1994 f150 v8 302 engine

93 to 95 Ford F-150 V-8 engine....firing orders!

I need an F150 trailer towing wiring diagram.

Check Out the Latest Top Trucks Report!

Top Ford Experts

ZJ Limited

Ronny Bennett Sr.

Thomas Perkins

Are you a Ford Expert? Answer questions, earn points and help others

Manuals & User Guides