BA Falcon gear lever moves freely (maybe too freely) but the gearbox doesn't shift out of park & the display on the dash still says P

SOLVED: Toyota highlander shift lever moves freely but - Fixya

https://www.fixya.com > ... > Toyota > Highlander
Sept 2, 2019 - First off, set the parking brake, raise vehicle so you can get under it. Remove the shift linkage from the transmission and manually move the shift lever to ...
I have a 2002 Toyota Echo. The end of the gear - Fixya
Oct 24, 2008
SOLVED: My 2001 toyota highlander will not shift into - Fixya
Sept 1, 2019
Transmission gear shift got stuck in Drive not able to move
Nov 20, 2019
Toyota sequoia gear shift lever broken - Fixya
Nov 16, 2019
More results from www.fixya.com

2001 V6 Highlander - Transmission Cable issue? - Toyota ...

https://www.toyotanation.com > forum > 816897-2001-...
Jun 9, 2014 - The shift lever moves VERY freely, but will not engage or come out ... It's probably a broken shifter cable , the joint at the transmission ...

Car in park shifter will move through gears but wont shif...

https://www.yourmechanic.com > Questions
Jul 13, 2016 · 1 answer
From what you've described, it sounds like the shifter cable came off at the transmission or the shifter. I'd suggest checking the shift ...

Automatic Transmission Problems Shifting Gears - Ira Toyota ...

https://www.toyotaofmanchesternh.com > automatic-tra...
One reason why an automatic transmission isn't shifting into gear has to do with the fluid. If it's not at the right level or the incorrect type has been used, ...

Check that the cable is routed correctly and didn't get hooked around something where it doesn't belong. Is it possible to put the bushing in backwards so it won't rotate properly? Also, check the linkage position to make sure it is properly synchronized with the shift lever. Finally, make sure the transmission position indicator matches the shift lever position. If you can move the lever in the wrong direction out of park, that would indicate one of the above misalignments.

I've been there and done that ...

Sorry I do not understand the question, are you saying it will not move when "D"

go under the car to side of transmission where linkage hooks to shift levers have someone shift the gears look to see if shifters on trans. are moving and the linkage is working fine.

First off, set the parking brake, raise vehicle so you can get under it. Remove the shift linkage from the transmission and manually move the shift lever to park. Then try moving the shift mechanism inside the car to park and then through each gear (engine off of course). See if the mechanism sticks, if so, probably a broken tab on the locking mechanism for the shift lever in the steering column. If it moves freely, try the lever on the transmission back and forth through the gear range to see if it sticks. If it sticks, or you can't initially move it by hand, you have a transmission problem that requires trained individuals to fix. If it moves freely also, try lubing the cable with silicone spray at all contact points, especially where it enters and exits any cable sheathing. (spray into sheathing well) If both move freely independent of each other, it may just have been in a bind, put both shifter and tranny lever in park and reattach the shift cable, Then try the gear range again from inside the vehicle.

try disconnecting cable to transmission turn the shifter on transmission manually down there connect cable again start car try it if not try it again turn once then connect cable again then try it if not the transmission is not good

Sounds like you need a new shift cable. Remove the shift cable from the linkage on the transmission. If the transmission linkage moves freely back into the park position and the shift lever inside the car still will not move back into park than the cable is bad. If the transmission shift linkage will not move back into park with the cable removed than the transmission will need to be pulled apart to service the shift rod.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

SHIFTER LOCKED IN PLACE

1. Remove the instrument panel cover below the steering column, then remove the steering column shrouds to gain access to the brake transmission shift interlock (BTSI) solenoid. The solenoid is part of the interlock cable assembly.
2. Disconnect the wire connector from the rear of the BTSI solenoid.
3. Insert the ignition key and turn it to the ON position.
4. With the brakes applied, try moving the shifter out of the PARK position.

• If the lever now moves freely in and out of PARK, perform the Circuit Test below.
• If the shift lever still does not move from the PARK position, remove the BTSI solenoid from the shift lever assembly. If the shift lever now moves freely in and out of the park position, the BTSI solenoid is faulty and the interlock cable must be replaced. If the shift lever still does not move from the park position, the problem is in the shift lever assembly or the ignition interlock cassette

center console shifter? if so, likely could be a misadj shift cable, you can pull loose top cover per instruction maneul tells you how to get out of park till you can get it adj, or repaired

Pull hard on the steering wheel to the left and the steering wheel lock mechanism should release. I mean pull hard to left because shift interlock is froze if you cannot get it this way you will need a pro to help! Good Luck Mate.