2004 745li po368 code camshaft sensor B-Bank 1 but where is it located?

It is definitely a cam problem. Was your replacement cam sensor OEM Japanese Denso, Made in China or Made in Mexico? Never go cheap on sensors.

DTC P0348 stands for Camshaft Position Sensor "A" Circuit High Bank 2. This code triggers when the signal coming from the CMP sensor located in bank #1 is either missing or inconsistent. The CMP sensor measures the speed and position of the engine's camshaft.
Sep 29, 2023

P0348 Code: Camshaft Position Sensor "A" Circuit High Bank 2

..

(1) Camshaft Position (CMP) Actuator Solenoid - Intake Bank 1
(2) Camshaft Position (CMP) Sensor - Intake Bank 1
(3) Camshaft Position (CMP) Sensor - Intake Bank 2
(4) Camshaft Position (CMP) Actuator Solenoid - Intake Bank 2
(5) Camshaft Position (CMP) Actuator Solenoid - Exhaust Bank 2
(6) Camshaft Position (CMP) Sensor - Exhaust Bank 2
(7) Generator
(8) A/C Compressor Clutch
(9) Camshaft Position (CMP) Actuator Solenoid - Exhaust Bank 1
(10) Camshaft Position (CMP) Sensor - Exhaust Bank 1

Which one ?
Camshaft Position Sensor Replacement - Bank 2 (Left Side) Exhaust Camshaft Position Sensor Replacement - Bank 2 (Left Side) Intake Camshaft Position Sensor Replacement - Bank 1 (Right Side) Exhaust Camshaft Position Sensor Replacement - Bank 1 (Right Side) Intake

Before you replace a part you may or may not need . Why ? What code ? Does the vehicle run ? There has been a lot of confusion on these vehicles with variable valve timing , mixing up cam sensors with camshaft actuators
DTC P0008: Engine Position System Performance Bank 1

DTC P0009: Engine Position System Performance Bank 2
The presence of DTCs P0008 and P0009 along with P0016, P0017, P0018, and P0019 indicates a possible condition with the primary timing chain and the alignment between both intermediate sprockets and the crankshaft. Or, the crankshaft reluctor wheel has moved and is no longer referenced to top dead center (TDC).

?€¢
Observe the scan tool CMP Desired, Actual, and Angle Variance parameters before a DTC sets. This may help to isolate whether a condition is specific to one camshaft, one bank, or caused by a condition with the primary crankshaft timing.

DTC Descriptors
DTC P0010: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 1

DTC P0013: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 1

DTC P0020: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 2

DTC P0023: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 2

DTC P2088: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 1

DTC P2089: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 1

DTC P2090: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 1

DTC P2091: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 1

DTC P2092: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 2

DTC P2093: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 2

DTC P2094: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 2

DTC P2095: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 2
DTC P0341: Intake Camshaft Position (CMP) Sensor Performance Bank 1

DTC P0342: Intake Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 1

DTC P0343: Intake Camshaft Position (CMP) Sensor Circuit High Voltage Bank 1

DTC P0346: Intake Camshaft Position (CMP) Sensor Performance Bank 2

DTC P0347: Intake Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 2

DTC P0348: Intake Camshaft Position (CMP) Sensor Circuit High Voltage Bank 2

DTC P0366: Exhaust Camshaft Position (CMP) Sensor Performance Bank 1

DTC P0367: Exhaust Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 1

DTC P0368: Exhaust Camshaft Position (CMP) Sensor Circuit High Voltage Bank 1

DTC P0391: Exhaust Camshaft Position (CMP) Sensor Performance Bank 2

DTC P0392: Exhaust Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 2

DTC P0393: Exhaust Camshaft Position (CMP) Sensor Circuit High Voltage Bank 2
I'm sorry but when dealing with these problems your best bet is to take your vehicle to a qualified repair shop , I have never see a DIY'ER correct the problem with these , an in the end always end up taking it to the dealer .

This picture here showing the engine from the rear.

Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty Camshaft Position Sensor

Generic OBD II Diagnostic Trouble Codes

DTC CODES P0300 to P0399

P0300....Random/Multiple Cylinder Misfire Detected

P0301....Cylinder 1 Misfire Detected

P0302....Cylinder 2 Misfire Detected

P0303....Cylinder 3 Misfire Detected

P0304....Cylinder 4 Misfire Detected

P0305....Cylinder 5 Misfire Detected

P0306....Cylinder 6 Misfire Detected

P0307....Cylinder 7 Misfire Detected

P0308....Cylinder 8 Misfire Detected

P0309....Cylinder 9 Misfire Detected

P0310....Cylinder 10....Misfire Detected

P0311....Cylinder 11 Misfire Detected

P0312....Cylinder 12 Misfire Detected

P0313....Misfire Detected with Low Fuel

P0314....Single Cylinder Misfire (Cylinder not Specified)

P0320....Ignition/Distributor Engine Speed Input Circuit

P0321....Ignition/Distributor Engine Speed Input Circuit Range/Performance

P0322....Ignition/Distributor Engine Speed Input Circuit No Signal

P0323....Ignition/Distributor Engine Speed Input Circuit Intermittent

P0324....Knock Control System Error

P0325....Knock Sensor 1 Circuit (Bank 1 or Single Sensor)

P0326....Knock Sensor 1 Circuit Range/Performance (Bank 1 or Single Sensor)

P0327....Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)

P0328....Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)

P0329....Knock Sensor 1 Circuit Input Intermittent (Bank 1 or Single Sensor)

P0330....Knock Sensor 2 Circuit (Bank 2)

P0331....Knock Sensor 2 Circuit Range/Performance (Bank 2)

P0332....Knock Sensor 2 Circuit Low Input (Bank 2)

P0333....Knock Sensor 2 Circuit High Input (Bank 2)

P0334....Knock Sensor 2 Circuit Input Intermittent (Bank 2)

P0335....Crankshaft Position Sensor A Circuit

P0336....Crankshaft Position Sensor A Circuit Range/Performance

P0337....Crankshaft Position Sensor A Circuit Low Input

P0338....Crankshaft Position Sensor A Circuit High Input

P0339....Crankshaft Position Sensor A Circuit Intermittent

P0340....Camshaft Position Sensor 'A' Circuit (Bank 1 or Single Sensor)

P0341 Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 1 or Single Sensor)

P0342....Camshaft Position Sensor 'A' Circuit Low Input (Bank 1 or Single Sensor)

P0343....Camshaft Position Sensor 'A' Circuit High Input (Bank 1 or Single Sensor)

P0344....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 1 or Single Sensor)

P0345....Camshaft Position Sensor 'A' Circuit (Bank 2)

P0346....Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 2)

P0347....Camshaft Position Sensor 'A' Circuit Low Input (Bank 2)

P0348....Camshaft Position Sensor 'A' Circuit High Input (Bank 2)

P0349....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 2)

P0350....Ignition Coil Primary/Secondary Circuit

P0010....'A' Camshaft Position Actuator Circuit (Bank 1)

P0011....'A' Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)

P0012....'A' Camshaft Position - Timing Over-Retarded (Bank 1)

P0013....'B' Camshaft Position - Actuator Circuit (Bank 1)

P0014....'B' Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)

P0015....'B' Camshaft Position -Timing Over-Retarded (Bank 1)

P0020....'A' Camshaft Position Actuator Circuit (Bank 2)

P0021....'A' Camshaft Position - Timing Over-Advanced or System Performance (Bank 2)

P0022....'A' Camshaft Position - Timing Over-Retarded (Bank 2)

P0023....'B' Camshaft Position - Actuator Circuit (Bank 2)

P0024....'B' Camshaft Position - Timing Over-Advanced or System Performance (Bank 2)

P0025....'B' Camshaft Position - Timing Over-Retarded (Bank 2)

I think your sensors are pattern parts and the readings /resistances are not the same as the original parts ,try some bosch units is my first suggestion ,

CAMSHAFT POSITION SENSOR IS LOCATED BANK 1 ON BACK TOP ENGINE HEAD. YOU ALSO ANOTHER CAMSHAFT POSITION SENSOR ON BANK 2 ON TOP FRONT OF ENGINE.YOUR PURGE SOLENOID VALVE IS ON BANK 2 ON TOP ENGINE HEAD CLOSE TO CMP SENSOR ON BANK 2 ALSO.