I need to know how to replace my turn signal switch on my steering wheel my windshield washer turner broke off so either I need to know how to fix the windshield washer switch or just replace the whole turn signal switch? I can use my windshield wipers I just have to hold the part that feel off I don't know if it had some spring to keep in place but I can't leave it on there and turn the dial to make my wipers go faster or slower. Hope I was detailed enough so you know what I am asking.

Switch is bad.

Sorry , no adjustment .
Wiper/Washer System Components
The Wiper / Washer System consists of the following components:
• Windshield wiper / washer switch
• Windshield wiper system module / motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR 25A fuse
Wiper / Washer System Operation
The windshield wiper motor module is part of the windshield wiper motor cover and controls the wiper motor operation. The windshield wiper motor is a 2 speed motor. Windshield wiper DELAY operation is a low speed wiper motor function with a variable delay interval between the wipe cycles. The DELAY interval is controlled through a series of resistors within the wiper / washer switch.
Park Position Operation
When the windshield wiper / washer switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the wiper motor module will continue to operate the wiper motor until the wipers reach the park position. If the ignition is turned off while the wipers are in mid-cycle, the wipers will stop immediately where they are. The wipers will park the next time the ignition is cycled to the ON position.

Do you know how to do diagnostic's ?

Wipers Blades Do Not Park
Step
Action
Yes
No
Schematic Reference: Wiper/Washer Schematics
Connector End View Reference: Wiper/Washer Connector End Views
DEFINITION: This table diagnoses the wipers operate normally but will not return to the park position when the wiper operation is cancelled.
1
Did you perform the Diagnostic System Check - Vehicle?
YES - Go to Step 2
NO - Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2
Turn ON the ignition, with the engine OFF.
Move the wiper switch to the LO position.
Move the wiper switch to the OFF position.
Do the front wipers advance to the park position?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Turn the ignition switch to the RUN position.
Turn the wiper switch to OFF.
Disconnect the wiper/washer switch connector.
Do the wipers park?
YES - Go to Step 7
NO - Go to Step 4
4
At the wiper/washer switch connector, measure the voltage of the windshield wiper switch signal 2 circuit.
Does the voltage measure greater than 1.0 volts?
YES - Go to Step 5
NO - Go to Step 8
5
Reconnect the wiper/washer switch connector.
Disconnect the wiper motor connector.
Measure the voltage of the windshield wiper switch signal 2 circuit.
Does the voltage measure greater than 1.0 volts?
YES - Go to Step 6
NO - Go to Step 8
6
Repair a short to battery positive voltage in the windshield wiper switch signal 2 circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
YES - Did you find and correct the condition?
NO - Go to Step 9
--
7
Replace the wiper/washer switch. Refer to Turn Signal Multifunction Switch Replacement in Steering Wheel and Column - Tilt.
YES - Did you complete the replacement?
NO - Go to Step 9
--
8
Replace the wiper motor cover. Refer to Wiper Motor Cover Replacement .
YES - Did you complete the replacement?
NO - Go to Step 9
--
9
Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 2

The steering column wheel has 2 pins pushed into the back side of it and as you turn the steering wheel making a turn, the pins slide over the humps of the blinker signal. As you return the wheel back to center to drive straight, these pins then hit the humps in the turn signal and push the turn signal back to the original position. It sounds like one of these pins fell out or broke off. You need to pull steering wheel and check to see if these pins are still inserted on the back side of the steering wheel.

no you can not you have to pull the steering wheel

buy a used multi-function switch for your car. these can be found on eBay and at junkyards/recyclers.
most likely any mid-90s GM will have the same switch. cost used about 20 bucks, new about 200 so find a used one as your car is only worth 500 bucks!

you are going to need someone who knows what they are doing to replace it as it sits under the airbag under the steering wheel. a body shop may well be cheaper than a dealer for that labor cost.

The windshield wiper/washer functions are incorporated into
a switch on the right side of the steering column. If the switch
is broken, you will need a repair manual to replace it or have
Honda take care of it.

The problem may be the windshield wiper switch on the steering wheel. My switch broke when I turned on my windshield washer fluid. It remain in the down position. All I did was put a peice of folded paper underneath the wiper switch to hold it in the up postion. That should keep them from coming on until you replace the whole wiper switch.

You can buy the turn signal switch at Napa or other auto parts stores. It's a combination switch. Remove the steering wheel and remove the 2 screws that hold the turn signal switch on, unplug the wires and installation is reverse of removal.

if you rigged up a seprate switch and it stoped woring all together it sounds like you need to replace the motor and the turn signal switch isnt that hard to do by yourself if your looking for cheap good luck and i hoped i helped

Changing the turn signal switch is a fairly involved process. You'll need to disable and remove the driver's side airbag, the steering wheel, and the SIR coil in the steering column. You'll need a steering wheel puller and a lock plate compressor, in addition to the normal assortment of sockets, screwdrivers and Torx drivers. Autozone has detailed instructions for disabling the airbag, removing the steering wheel, and replacing the switch on their web site. I printed their directions and several of the diagrams and was able to replace the switch without any major problems.

Be prepared to spend some time on this--even the simplest steps can take more time that you expect. Case in point: Step 1--disconnect the negative battery terminal. To do this on my 96 Cutlass required removing a cross member under the hood and the windshield washer reservoir.

Good luck!