Remove radio - 1989 Dodge Spirit

Question edited for clarity.
Question moved to model category.

The year is needed, but here are some videos. If you mean 'how to get into' once you have removed it, break the paper seals and undo the screws, and remove the top.

How to remove interior panels to remove radio.. 2019 ...

Kia Optima Forums https://www.optimaforums.com > threads > how-to-re...
Apr 4, 2020 - The Fora platform includes forum software by XenForo. OptimaForums.com is an independent Kia enthusiast website owned and operated by ...

How To Remove Factory Radio In 2009 Kia Optima. Does The ...

diyforums.net https://www.diyforums.net > how-to-remove-factory-r...
Now pry around the edges of the radio/climate control to loosen the retaining clips and pull away the trim panel. You will have to remove the wiring harness ...

Kia Optima Stereo Removal, Install and Repair

Car Stereo Removal https://www.carstereoremoval.com > htm > stereoremo...
Car Stereo Help - Kia Optima Car Audio - Car Radio, speaker and amplifier - remove, replace, repair and More. https://CarStereoHelp.com Car Stereo Help !

How do you remove radio from 2002 Kia Optima?

Answers https://www.answers.com > Auto > Asian Cars
Oct 22, 2022 - To remove the dash to get to the radio from a 2005 Kia Optima, begin by prying around the edge of the trim around the gear shifter. Then, remove .. ..

Module - Generic Electronic (GEM)/Central Timer (CTM) Removal

1. CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage may result. Depower the supplemental restraint system (SRS). For additional information, refer to Section 501-20B .

1. Remove the audio unit. For additional information, refer to Section 415-01 .

1. Remove the center instrument panel finish panel.
   1. Remove the screws.
   1. Remove the center instrument panel finish panel.
   • Disconnect the electrical connectors.
   • Remove the GEM/CTM.
     1. Remove the screw.
1. Disconnect the four connectors from the GEM/CTM.
1. Remove the GEM/CTM.
2. Installation
1. NOTE: When the battery is disconnected and reconnected, some abnormal drive symptoms may occur while the vehicle relearns its adaptive strategy. The vehicle may need to be driven 16 km (10 mi) or more to relearn the strategy.

Special Tool(s) Radio Removing Tool
415-001 (T87P-19061-A) Removal

1. Remove the radio chassis.
   1. Insert Radio Removing Tool into the radio face plate and release the radio retaining clips.
   1. Pull outward on Radio Removing Tool to remove the radio chassis from the instrument panel.
   3. Remove the radio.
      1. Disconnect the electrical connectors.
      1. Disconnect the radio antenna lead in cable.
      1. Remove the radio.

here is the online fsm quote

1. Disconnect the negative battery cable.
2. Open the glove box. Remove the glove box open panel.
3. Remove the air conditioning switch connector and heater control unit lever knobs. Pull heater control unit cover plate from instrument panel.
4. Remove the gearshift control lever upper boot and center console.
5. Remove the ashtray.
6. Remove the instrument panel center trim bezel and radio face plate.
7. Remove the screw from the back of the radio receiver and the screws from the front face of the radio.
8. Remove the radio.

NOTE: The following procedure may vary a bit from the system which you have in your car.
TO REMOVE RADIO RECEIVER ASSEMBLY
(a) for Integrated with Panel:
(1) Disconnect the hazard warning signal switch
connector.
(2) Remove the 4 bolts.
(3) Disengage the 4 clips and the 4 claws and
remove the radio receiver.
(4) Disconnect the plug.
(5) Disconnect the 3 radio connectors.
(b) except Integrated with Panel:
(1) Remove the 4 bolts and the radio receiver.
(2) Disconnect the plug.
(3) Disconnect the 2 radio connectors.
1. REMOVE INSTRUMENT PANEL CENTER REGISTER
ASSEMBLY (for Integrated with Panel)
2. REMOVE RADIO BRACKET RH
(a) for Integrated with Panel:
(1) Remove the 4 screws and the radio bracket.
(b) except Integrated with Panel:
(1) Remove the 4 screws and the radio bracket.
3. REMOVE RADIO BRACKET LH
HINT:
Use the same procedure as for the RH side.

REMOVAL

1. Disconnect and isolate the battery negative cable.
2. Remove cup holder.
3. Remove trim panel above cupholder by pulling straight out.
4. Remove center instrument panel trim panel.
5. Remove screws holding radio to instrument panel.
6. Pull radio rearward to gain access to the back of radio (RADIO). CAUTION: Pulling the antenna cable straight out of the radio without pulling on the locking antenna connector could damage the cable or radio.
   
7. Disconnect the antenna cable by pulling the locking antenna connector away from the radio (ANTENNA TO RADIO).
8. Disconnect bolt holding ground strap to the radio (if equipped).
9. Disconnect the wire connectors from the back of the radio.

Hi there,

Locate and remove two (2) phillips screws that secure the top of the plastic panel that surrounds the radio. The plastic dash panel will pull off once the screws are removed as shown in the photo above.
The front of the radio is held in with two (2) 7mm bolt screws at the top of the radio. Remove the 2 bolt screws.
There is a hidden radio that secures the rear of the radio and is located under the radio. Pull the ashtray to its extended position. You will need to lay on your back or side and look behind the ashtray, up to the bottom of the radio.
Once the ashtray has been pull to its extended position, you should be able to locate and remove one (1) 7mm bolt screw as seen in the photo above.
Once all screws have been removed, the radio can then be removed. Pull firmly on the radio to remove it from the dash. The radio will most likely resist pulling from the dash. The antenna cable which plugs into the rear of the radio is very short and gives the radio resistance when trying to pull the radio out of the dash. Continue to pull firmly and the antenna cable will unplug itself as the radio is pulled from the dash.
Unplug (1) blue, (1) white, and (1) black wire harness connector(s) from the rear of the radio. There will also be wires extending from the rear of the radio with a plastic connector attached to the wires about 4 inches from the rear of the radio. Unplug this small connector. The radio can now be completely removed from the dash. Set it aside. You will need to remove the plastic brackets attached to the top and bottom of the GM radio. This will be shown in detail in the "Mount New Radio" section.

Hope these helps....

Radio Reciever/Amplifier/Tape Player/CD Player REMOVAL & INSTALLATION Fig. 1: Remove the bezel retaining fasteners and the bezel . . .

1. Disconnect the negative battery cable.
2. Remove the center cluster screws and bezel.
3. Remove the radio attaching screws.
4. Disconnect the radio from the instrument panel wiring harness and antenna.
5. Installation is the reverse of removal. Fig. 2: . . . then remove the radio retaining fasteners
   Fig. 3: Slide the radio forward so that you may gain access to the electrical connections
   Fig. 4: Disengage the antenna and radio electrical connections
   

Here ya go!


Exploded view of the radio, tape player or CD player removal, 1990-94 vehicles

1. Disconnect the negative battery cable. Wait at least 60 seconds before beginning the remainder of the procedure, in order to disarm the Supplemental Restraint System (SRS).
   
2. Using a plastic trim tool, remove the radio panel. Pry the lower part of the radio panel away first, then separate and remove the panel.
   

Using a plastic trim tool, carefully pry the radio trim panel away


Remove the center trim panel for access to the radio retainers

WARNING When removing and installing the floor console, do NOT allow it to bump against the SRS-ECU!

1. For 1995-98 vehicles, remove the floor console assembly, as outlined in Section 10 of this manual.
   

1. Remove the mounting bolts and pull the radio receiver, tape player or CD player out slightly. Detach all harness connectors and remove the unit from the vehicle.
   

After removing the console, unfasten the radio mounting screws


Pull the radio out enough to access the connectors


Unplug the electrical connector from the rear of the radio ...


... then disconnect the antenna lead and remove the radio from the vehicle


Installation is the reverse of the removal procedure.

you need specail radio removal tools. they spread 4 spring clips.

1. Remove the radio chassis.
2. Insert Radio Removing Tool into the radio face plate and release the radio retaining clips.
3. Pull outward on Radio Removing Tool to remove the radio chassis from the instrument panel.

Special Tool(s)

Radio Removing Tool
415-001 (T87P-19061-A)

remove the trim around the radio face be careful not to break it, it should snap off its a delicate proceedure take radio face plate off ( if equipped) radio should come out