At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
If it is stuck in the seat belt clip (meaning its buckled) then that model year had a seat belt buckle recall for failure. If its stuck in the seatbelt retractor and your seatbelt retractor is floor mounted there is a release pin on the ratchet gear. TO access it you will need to remove the plastic cover located at the floorboard next to the door on the side of the car that is stuck. If its a seat mounted retractor this means the retractor mechanism is located within the seat frame. You will need to view the bottom of the seat of the belt and see the anchor point. Seatbelts must be anchored to frame of car. Trace it into the seat back. If its located in the back of the seat you will need to remove the seat cover to the extent to reach the mechanism. This can be located at the bottom of the seat.. but more than likely is located at the shoulder area. The Seat cover (fabric) is removeable via clips located at the base and tucked into the seat (think hidden bra/pant clip style connectors or zipper) If you have leather seats it is a bit more detailed and more difficult to manage the seat covers. Typically your local Chevrolet dealer mechanic can get this done in 10 minutes (based one experience) and quite possibly wont charge you or charge you minimally. The downside to this is if its locked that means the same gear that locks it in an accident was frozen in place somehow and this typically indicates a dirty dirty spring or broken spring mechanism. The locking pin operates on centrifugal force and activates based on speed by which the seat belt is pulled out. (just a bit of knowledge) Good luck
pull the seatbelt pilar cover off from the door jamb. this runs vertically up the pilar between the front an back door (beside the front seats. Once opened loosen the belt by gently pulling the belt upward toward the roof. You'll have to do this sometimes in small increments. Once the seatbelt is pulled out all the way, spray small amount of lubricant into the joint where at the top of the belt spool. Also use a screw driver to push spool upward while pulling the belt. At first it's only going to release a little but eventually the lubricant will work its way into the seam at the top of the belt spool and loosen up the stuck inertia catch. Until it completely loosens you might have to remove the pilar cover again and work the seatbelt out (also use the screw driver technique described above) in order to use the seatbelt. When parking, I would relatch the seatbelt and pull the slack up around the back of the head rest. After a day or so it worked normally.
this is a simple repair many dont know. remove or pull off plastic pillar post cover, seatbelt probably twisted inside. twist it back around so it runs flat and lube slightly with a light lube spray on metal gearing. i had the same problem w mine pk
pull the seatbelt pilar cover off from the door jamb. this runs vertically up the pilar between the front an back door (beside the front seats. Once opened loosen the belt by gently pulling the belt upward toward the roof. You'll have to do this sometimes in small increments. Once the seatbelt is pulled out all the way, spray small amount of lubricant into the joint where at the top of the belt spool. Also use a screw driver to push spool upward while pulling the belt. At first it's only going to release a little but eventually the lubricant will work its way into the seam at the top of the belt spool and loosen up the stuck inertia catch. Until it completely loosens you might have to remove the pilar cover again and work the seatbelt out (also use the screw driver technique described above) in order to use the seatbelt. When parking, I would relatch the seatbelt and pull the slack up around the back of the head rest. After a day or so it worked normally.
1)move the plastic cover over the seat belt out of the way to gain access to the two mounting bolts for the seat belt mechanism. Use a 10mm wrench and a 14mm wrench and remove the two bolts holding the seat belt mechanism to the body. Use a small drill bit or small screwdriver and make one hole in the plastic cover on each side of the seat belt mechanism (the covers say "do not remove plastic cover". Spray lots of wd40 in each hole. Then exercise the seat belt. When the mechanism allows the belt to be retracted, retract the belt all the way out and exercise the seat belt. Reinstall mechanism with both mounting screws in original position and put plastic cover back in place. Good luck. New seat belt costs $100.00 from dealer and are hard to find working in junk yards. I have fixed several of them this way.
you can remove the bolt that holds the seatbelt to the floor by pulling off the seatpad where the belt goes to the floor and then raise the seat and the belt should reset. this happens on my passenger side rear seat.
×