Keyless entry hi i lost my original key that comes with the keyless lock / unlock buttons any clues please

Theft Deterrent Arm/Disarm Modes
Important: Although mode 2 provides increased security, the content theft deterrent system disarms only by pressing unlock on the keyless entry transmitter. This can pose a problem if the keyless entry transmitter is damaged, lost, or inoperative for any reason while you attempt to disarm the content theft deterrent system.
Mode 1: The system arms when you lock the doors with the keyless entry transmitter. The system disarms when you unlock the left front, right front, or liftgate door with the key or the keyless entry transmitter. The system does not arm when you lock the doors with a power door lock switch.

Mode 2: The system arms when you lock the doors with the keyless entry transmitter. The system disarms when you unlock the doors with the keyless entry transmitter. The system does not disarm when you unlock the doors with the key.

Mode 3: The system arms when you lock the doors using a power door lock switch or the keyless entry transmitter. The system disarms when you unlock the left front, right front, or liftgate door with the key or the keyless entry transmitter.
Changing the Feature Customization Modes

1. Turn off the IP dimmer switch.
2. Turn the ignition switch to the LOCK position.
3. Remove the BCM PRGRM fuse.
4. Turn the ignition switch to the ACC position. The BCM flashes the fasten belts indicator and sounds the chime 4 times, which indicates that BCM type 4 is installed on the vehicle. At this point, the BCM has entered the feature customization mode.
5. In order to change the theft deterrent/shock sensor mode, turn the headlamp switch from OFF to PARK and back to OFF.
The BCM flashes the fasten belts indicator and sounds the chime a number of times equivalent to the theft deterrent/shock sensor mode. A transition past mode 4 repeats the sequence starting with mode 1.

6. Complete the following steps in order to change the theft deterrent arm/disarm mode:

6.1.
Insert the key in the left front, right front, or liftgate door lock cylinder.

6.2.
Rotate the key from the center to the unlock position.

6.3.
Press the horn button on the remote keyless entry transmitter.

6.4.
Count the number of chimes that you hear. The number of chimes tells you which mode you have set.

6.5.
Press the horn button again in order to change the mode. Continue to press the button until you hear the number of chimes that indicates the mode that you want.

6.6.
Turn the key back to the center position and remove the key from the door key cylinder.

In order to exit and save the current feature customization modes use the following procedure:

1. Turn the ignition switch to the LOCK position.
2. Reinstall the BCM PRGRM fuse.

If you are unable to change locking modes Theft Deterrent System Feature Customization Inoperative

Jeep 1990 and later Remote keyless entry programing

Put the key in the ignition with all doors and trunk closed

Open the driver's door on the automobile and leave the door open.

4 Move the switch on the door to the lock position while the door is open.

5 Switch the key in the ignition two clicks to the right to the "On" position. do not start

6 Press the lock button on your keyless remote for your Jeep and hold the button for 5 seconds. Release the button and remove the key from the ignition to complete the programming.

Read more : http://www.ehow.com/how_5019251_program-keyless-entry-jeep.html

1. 1 Press the lock button on your Chrysler remote five consecutive times at brief two second intervals.
   
2. 2 Place your key in the car's ignition and turn it to the right two clicks to the "Run" position on all Chrysler cars.
   
3. 3 Hold the unlock button. Then press and hold the panic button simultaneously. Release both buttons at the same time and you will hear a small beep to indicate that the programming is in effect.
   
4. 4 Press and release both the lock and unlock buttons at the same time.
   
5. 5 Turn the key to the off position and remove it from the ignition. Test your remote to see if the programming was successful.
   

Read more: How to Program a Chrysler Keyless Entry Remote ' eHow.com http://www.ehow.com/how_5014707_program-chrysler-keyless-entry-remote.html#ixzz1ANbOsavi

Have a seat in your Honda and close the doors, but make sure they are unlocked.

2

Turn your ignition key to the "On" position, labeled by two lines (II). Press the "Unlock" button on your keyless remote. Turn your ignition key to the "Off" position.

3

Repeat the procedure three times, and then turn the ignition key to "On." Immediately press the "Lock" button on your keyless entry. Listen for the doors to lock, and then unlock to signal that you are in programming mode.

4

Press the "Lock" button on the keyless remote, and then turn the ignition to the "Off" position to confirm.

Read more: How to Program a Honda Keyless Entry ' eHow.com http://www.ehow.com/how_5523557_program-honda-keyless-entry.html#ixzz1A7h1nyC1

Hi.

To program ( or reprogram ) a keyless entry remote transmitter into the remote keyless entry module, perform the following steps:

1. Turn the key to ON or ACC and short the two terminals of the program connector, a two-pin connector located below the driver's side of the instrument panel at the base of the steering column. All doors should lock and then unlock.
2. Press any button on each keyless entry remote transmitter in turn. All doors should lock and then unlock. If the door locks do not respond, press the button again (up to three times maximum with the same keyless entry remote transmitter). If the door locks still fail to respond, go to Pinpoint Test A.
3. Repeat Step 2 to program additional keyless entry remote transmitters into the remote keyless entry module (up to four keyless entry remote transmitters maximum).
4. Turn key off.
5. Remove the short from the program connector. All doors should lock and then unlock.
6. Verify that the keyless entry remote transmitters have been successfully programmed by pressing the LOCK or UNLOCK button on each one, and observing that the system responds by locking and/or unlocking the doors.


I hope this helps you.

Thanks!

To program the transmitters, perform the following procedure while seated in the vehicle driver's seat:

Close all the vehicle doors.
Remove the ignition key from the ignition lock cylinder.
Press and hold unlock on the door lock switch.
Important: To successfully enter the keyless entry programming/diagnostic mode, steps 4 through 6 must be completed within 25 seconds of pressing the door unlock switch.

While holding the door lock switch in the unlock position, insert and remove the ignition key twice. Do not rotate the ignition lock cylinder.
Insert the ignition key a third time leaving the key in the ignition lock cylinder. The ignition must remain in the LOCK position for the rest of the procedure.
Release the door lock switch. The chime will sound three chimes to signal that transmitter programming/diagnostic mode is active.
Press and hold the lock and unlock buttons at the same time on the keyless entry transmitter for approximately 4 seconds. The chime will sound two times to signal that the transmitter has been programmed successfully.
To exit the transmitter programming/diagnostic mode perform either of the following:
• Turn the ignition switch to the RUN position.

• Remove the ignition key from the ignition switch

it's in owner manual. But, first you have to enter your original code and it must work. then you press the 1 button and then enter a new 5 digit code, then press the 1 button again.

Keyless Entry Keypad To unlock the driver front door (20124) , and disarm the anti-theft alarm control (19A366) , (if equipped):

• Enter the permanent factory code.
• Enter the owner's alternate code.

To unlock the passenger door(s), press the 3/4 button within five seconds of unlocking the driver door or luggage compartment. To unlock the luggage compartment door (40110), press the 5/6 button within five seconds of unlocking driver or passenger door(s). To turn on the courtesy lamps and light all illuminated components, lift either front door handle (22404) or press any button on the keyless entry keypad (14A626) . To lock all doors, press the 7/8 and 9/0 buttons at the same time with all doors closed. (It is not necessary to enter the key code first.) This will turn off courtesy lamps and arm anti-theft alarm control (if equipped). To program an alternate code:

1. Enter the five digit permanent entry code into keyless entry keypad .

1. Within five seconds of pressing last button of permanent code, press the 1/2 button within five seconds of pressing the last button of the permanent code.

1. Enter any alternate five digit code within five seconds of pressing 1/2 button.
   • Enter a sixth digit as follows to indicate operator's memory seat setting to be set by alternate code:
     • 9/0 — no memory recall
     • 1/2 — memory seat position 1
     • 3/4 — memory seat position 2
     • 5/6 — memory seat position 3
   • After successful programming, the doors will signal by locking and then unlocking.

---------------------------------------------

• Keyless Entry Keypad Does Not Work Properly

• Circuit.
• Keyless entry keypad.
• Electronic door lock control processor.

Open Fuses:

• Town Car and Crown Victoria/Grand Marquis
• Power Distribution Box (under hood)- K, 40A (Maxi)
• Instrument Panel Fuse Panel - 17 (10A), 10 (20A), 8 (15A), 5 (15A) and 4 (10A)

Loose Connectors

Corroded Connectors

Transmitter Programming Notes Transmitter Programming

1. Start with the ignition OFF, hold down the power unlock button on the door panel. Turn ignition key ON, OFF, ON, OFF. Release power unlock button on the door panel. The locks will cycle once.
2. Hold down the keyless entry transmitter LOCK and UNLOCK buttons for 15 seconds . The locks will again cycle once.
3. Repeat step #2 for each additional keyless entry transmitter.
4. Turn the ignition on to exit the keyless entry transmitter programming mode. Programming is now complete

does the key pad light when you press a button at night? If yes, the fuse is ok.
Do you have the plastic card with the permanent code in your owner manual packet? If yes, tryit.
report back.

Keyless Entry The keyless entry keypad is hardwired to the GEM. The GEM interprets the inputs from the keyless entry keypad and then controls the associated operation. The keyless entry keypad will be illuminated for five seconds when any button is pressed. Additionally, it will request the illuminated entry feature to turn the courtesy lamps on. If a lock all doors code is entered, the illumination will turn off, as well as request the illuminated entry feature to turn off the courtesy lamps. When pressed, the keyless entry keypad supplies the ground signal to the GEM or the GEM receives a signal from the keyless entry remote transmitter. Then the GEM outputs a ground signal to the appropriate lock or unlock relay which supplies the power to the actuator to lock or unlocks all doors, including the luggage compartment. The keyless entry remote transmitter also unlocks the liftgate or activates the panic alarm by sending a signal to the GEM.
--------------------------------------------------------------- Visual Inspection Chart Mechanical Electrical

• Keyless entry keypad
• Keyless entry remote transmitter

• Central junction box (CJB) Fuse F222 (20A)
• Circuitry
• Generic electronic module (GEM)

------------------------------------------------------------------------

• No communication with generic electronic module (GEM)

• Generic electronic module.
• Circuitry.

• REFER to Section 419-10 .

------------------------------------------------------------------------------------

if you can drop back seats you can get in and manually flick the lever when it is open you will have to go to dealer to see if you can get a key to match or you might get 1 in a junkyard. if this helps please rate me