My abs control lights up and a small motor noise starts once i make a right hand turn i've had the hub change and rotor,brakes caliber and chevy dealer check the wiring harness and stated that abs motor is good and all wire are good what can this problem be the chevy dealer doesn't know the problem.

Do yourself a favour and for your own safety, take it to a Suzuki garage for repair.
Brakes that don't work properly are very dangerous.

Service Traction Control - Stabilitrak and ABS light, Help - Page ...

chevroletforum.com > ... > Tahoe & Suburban

Aug 16, 2012 - Service Traction Control - Service Stabilitrak and ABS light came on. ... Its supposed to still be under warranty, "Major Guard". ... I replaced my rear shocks with OEM re-manufactured Arnott shocks (great company) and in the ...

SilveradoSierra.com • Traction Control, Stabilitrak & ABS Issue

www.silveradosierra.com/.../traction-control-stabilitrak-abs-issue-t18976...

Jan 28, 2014 - Traction Control, Stabilitrak & ABS Issue. Tue Jan 28 ... The wife and I got in to head out and see my brother and as soon as I turned the key the ServiceTraction Control, Service Stabilitrak messages flashed and the ABS light came on. ... check your wheel bearings my was gone and caused the same thing ...

Chevrolet Impala Questions - Hello. I have a 2012 Chevy ...

www.cargurus.com > Questions > Chevrolet > Impala

CarGurusApr 6, 2013 - Occasionally when I hit the brakes I get a Stabilitrak Error Message " ... I believe GM still had 3 year/ 36,000 mile bumper to bumper ... After about 2 months of intermittent noises the ABS light came on, the service stabilitrak warning, servicetraction ... Edit....left hub bearing change after the right one changed.

Replaced front hub - now ABS/Stabilitrak lights on... - Chevy ...

Is your ABS working properly? Under heavy braking the ABS should engage and 'pulse' the brakes on/off. It is normal to feel the brake petal flutter or pulse under your foot.

Under light braking there should be no pulsing as the ABS does not engage and you have changed the rotors and pads.

Rotors could be one problem.Check fluid level.Who did the brakes.Abs is sensor which is in hub bearings .Could be bad.

Bang harder. They tend to rust up where it meets the hub and seize up. Eventually it will come loose. If it's the rear rotor once you can wiggle it you will be able to work it around the brake shoes if needed. Most of the time ounce you get it broken free from the hub they slide right off.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

I'd first make sure the new pads are the correct size. Doesn't happen very often but maybe the parts person gave you the wrong size pads ( for the smoking problem). As for the ABS light, most newer cars will throw out codes if you wait too long to change them out, I would contact a chevy dealer or search online about reseting the code (light).

Traction control and anti-locks(ABS) lights come on there is sensors that are pluged in behind the rotors check and see if they are disconected or loose sometimes when you change your brake pads they might come loose and not making contact.

I'm guessing you DID resurface the rotors or replaced them? On the bearing make sure it is not overtightened. With the car lifted can you turn by hand and listen?
Not positive about brakes I've always understood they bleed like regular brakes but I would consult a repair manual or dealer (just ask service advisor) Good luck!

mid size blazer- take off wheel-brake caliper-brake caliper bracket- rotor-and behind the hub u will see a wire going into the back of hub and is secured by a hex/torx head bolt that is ur abs sensor it looks like a small cylinder with wires attached---on the s-10 blazer some of the abs sensors set ups-- are part of the hub assembly/wheel bearing would have to change the whole unit

i have a 2002 chevrolet impala and the same thing happened to me. abs light came on as well as my traction controll light. when i would step on the gas or brakes my car sounded like the brake pads were skiping against my rotors. i had my hub sensor replaced 5 times. the machanic kept telling me it was the part that need to be replaced.they hooked it up to have a dianostic done and the computer keep telling them to replace the hub sensor. so finally we brought my car to an electric auto shop. they found it was a loose wire that was turning my brakes on and off.(haywire)they fix my car in 30mins.