How to remove just the bulb on silver star ultra 9005

If you need to replace the low beam or high beam bulbs in the Driver Side headlight assembly, just pop open the hood and reach in behind the housing.
The low beam bulb is located at the top of the headlight and the high beam bulb is located just below it. Remove them by first rotating the base of the bulbs 1/4 turn counter clockwise and then pull them straight out. Press the release tab on the power connector, slide it straight off, and push on a new # H11 low beam or # 9005 (HB3) high beam bulb.

If you need to remove any of the headlight or turn signal bulbs on the Passenger Side, you'll first need to remove the engine air box.

Use a Torx T-25 star bit screwdriver to remove the four screws that hold the top half of the engine air box in place. Set them aside in a safe place.Pull out the engine air filter element and set it aside with the air box screws.
Carefully pull upwards on the lower half of the air box until it pops out of the engine bay. It is held in place by a few plastic pegs that act as friction fasteners.
With the lower half of the air box removed, you can easily access the low beam bulb at the top and the high beam bulb just below it.

On 2002 Oldsmobile Alero Car Light Bulb Size, check this list:

Low Beam Headlight Bulb Size: 9006 or 9006 HID Upgrade KitHigh Beam Headlight Bulb Size: 9005 or 9005 HID Upgrade KitParking Light Bulb Size: 3157NALLFront Turn Signal Light Bulb Size: 3157NALLRear Turn Signal Light Bulb Size: 3157LLTail Light Bulb Size: 3157LLStop Light Bulb Size: 3157LLHigh Mount Stop Light Bulb Size: 921Fog/Driving Light Bulb Size: 894License Plate Light Bulb Size: 194Back Up Light Bulb Size: 921Front Side Marker Light Bulb Size: 194Rear Side Marker Light Bulb Size: 2825Glove Box Light Bulb Size: 194Map Light Bulb Size: 212-2Dome Light Bulb Size: 212-2 or 561Step/Courtesy Light Bulb Size: 168 or 73Trunk/Cargo Area Light Bulb Size: 211-2

Hope helps.

In most GM cars you can access the headlight bulb for replacement by removing the entire headlight assembly. This is usually held in place with 3 -10 millmimeter bolts. Use a towel over your painted bumber cover to keep from scratching as you remove the assembly. You can then access the bulb insert on the rear of the assembly. Be sure to use gloves when handling the new bulb...our hands emit a grease that shortens the life of the halogen bulbs. Also use bulb grease at the base of the bulb to insure good contact and moisture elimination. If you consider replacing both low beam front bulbs, look at the Sylvania Silver Star replacements. These are legal and are 3 times the candle power of the original bulb...you will enjoy the difference. The Silver Stat is available in 2 models...$35. to $45. for two. Hope this helps.

With halogen capsule:
9006 for low beam ,9006SU for Silver Star Ultra,9006CB for cool blue
9005 for High beam, 9005SU for Silver Star Ultra, 9005CB for cool blue

With sealed beam:
H4666 for high/low beam, H4666ST for silver star, H4666XV for extra vision, H4666CB for cool blue

Lift the hood and remove the bulb from the inside rear of the headlamp. The bulb assembly has ears on it that you use to unscrew the bulb. Look at the autozone link below to see the bulb. Installation is reverse of removal. Note: DO NOT TOUCH THE NEW BULB GLASS WITH YOUR FINGERS!! They are halogen bulbs and will burnout.



http://www.autozone.com/autozone/parts/Silver-Star-Headlight/2008-GMC-Yukon-2WD/_/N-js79yZ9ci8c?counter=0&itemIdentifier=862293_0_7179_

Your really messed up
First ,get an owners manual,if you don't have one already
Then always look up what the bulb or lamp # is,BEFORE you buy them. Looking up fuses and bulbs,is the main reason you ,absolutely need the owners manual.
You also need one, so all these silly people,stop asking what the check lights are for.

there are two white or black clips directly behind the headlamp assy. pull up on them and the headlamp will release remove the headlamp assy in the back are your two headlamp bulbs as well as your drl bulb
hi beam is 9005 lo beam is 9006

Things You'll Need:

• #H11-55W and #9005 replacement bulbs (low- and high-beam bulbs for 2007 and later models)
• #9006 and #9005 replacement bulbs (low- and high-beam bulbs for 2002-2006 models).

STEPS TO REPLACE HEAD LIGHT: Shut off the Camry's engine and set the parking brake for added safety. Also, make sure its headlights are switched off. Open the hood using the primary and auxiliary hood release latches. Locate the back of the headlight assembly and determine whether the low- or high-beam bulb needs to be replaced. Turn the headlight bulb socket counterclockwise to remove it from the assembly. Unplug the electrical connector from the back of the bulb. Carefully dispose of the bulb to prevent it from shattering or cracking.

1. 
   

under the hood theres two bulbs in each headlight, your looking for the inner one. twist it to remove it. the bulb you need is a 9005 bulb, available at any autoparts store for 10-15 dollars.

if you cant get behind the headlight with your hand / you may need to take out the headlights then put them in but be careful most cars that you take the headlights out you must pull the bumper off / if you have to take the bumper off thentheir are retainers up top and on the bottom of vehicle also on the fenders there is a bolt to pull of bumper