Rear wiper not working. is it on a different fuse?

In the under hood fuse box , should have diagram inside the lid . Front wiper's or rear ? Front fuse # 36 - 25 amp. Plus Two relay's PCB hi and Wiper PCB relay . Wouldn't think this being fuse problem . Wiper switch , motor etc... The wiper's are control by a computer . BCM - body control module .

The windshield wiper/washer system consists of front and rear wipers. The front and rear wipers are operative when the vehicle is in accessory or run. The front wipers have 4 different modes: Mist, Intermittent, Low, and High. When the front wipers are in the intermittent mode, there are 5 delay modes to chose from, commanded by the windshield wiper washer switch through the body control module (BCM). The rear wipers has an only one mode.

If the fuse is bad , could have a short to ground or wiper motor pulling to much current (amps) . Fuse's don't just blow for no reason ! Could also have DTC'S - diagnostic trouble codes stored in the BCM .
DTC B3715
DTC B3873
DTC B3875
DTC B3922

DTC B3715 02: Front Wiper Relay Drive Circuit Short to Ground
The body control module (BCM) controls the wiper motor based on input from the windshield wiper washer switch. The BCM monitors the wiper washer switch through three separate signal circuits and a ground circuit. The windshield wiper switch high signal circuit is used to determine high speed wiper operation, the windshield wiper switch low signal is used to determine low speed, intermittent, and mist operation through the use of a resistor ladder, and windshield washer switch signal circuit is used to determine washer operation.
The BCM controls the windshield wiper motor through two output controls, controlling two different PCB relays which control the desired wiper speed, high or low.
DTC B3922 00: Front Wiper Function Select Circuit

The PCB relay's are non- servicable , replace fuse box . Soldered in Your best bet mit be to take it to a qualified repair shop .

Hey Joe , what make model an year vehicle ?

No there is not just one ,the rear has it's own fuse an relay . Fuse J - 20a in ( PDC ) power distribution center , relay should be in same box ! sorry don't have location number , can't find it !

Your wiper and wiper fluid motors are different operation. The fluid one is a pump and the wiper motor only operates the wipers. Should check and see if you are getting power to the wiper motor if you are and the wiper does not work then you may need a new wiper motor.

check rear wiper fuse and relay.if wiper motor getting power but do not work.rear wiper motor bad.if fuse and relay okay but no power going to rear wiper rear wiper switch could be bad.

Check fuses, front and back wiper motors run on different fuses. Test for power and ground at front wiper motor wires. If you have power and ground there your wiper motor may be toast. Good luck

My wife has a 08 Fox and her front wipers stopped working it's just a fuse in bank 7 a 10 amp just replace with a new one or swap for the 10 amp fuse in bank 11 (just a warning lamp for the handbrake) until you get a new one. ;-)

Look for the fuse for the rear wiper motor is a 15 amp mini-fuse , in location # 8 of your POWER DISTRIBUTION BOX in the engine compartment. Check in the PD BOX for; - relay # 8 is the rear wiper down relay , and - relay # 10 is the rear wiper up relay .

1. check the fuse to the rear wiper motor
2. check for power to rear wiper motor at the motor (power wire going in to the wiper motor with rear wiper switch on)
If you have good fuses & have power going in to the rear wiper motor...
3. Pull old rear wiper motor and install a new rear wiper motor.
Thank you please drive thru......

If the Fuses are good and the Rear Works the Cause will be the Wiper Motor for the Windshield Wipers. Please Rate My Response! Thanks!