1996 Chevrolet K1500 Logo

Related Topics:

Posted on Jul 13, 2017

I need the transfer case dash switch for a 1996 chevy c/k1500. Carquest site says part number 19168766. Everywhere else I've looked says this part is for years 97 and later. It looks the same in the picture. How do I know before I buy it that I am getting the right part. The front of the plastic switch is broke and the switch started to have intermitent problems when it did. My question is, where can I find the right part?

5 Related Answers

dcgun007

Doug Crawford

  • 63 Answers
  • Posted on Jun 22, 2009

SOURCE: 1996 s10 LS abs light in dash

take it to auto zone or advance or pep boys have them scan it. They will do it for free. let me know what happens...gl...DC

Ad

Anonymous

  • 336 Answers
  • Posted on Aug 19, 2009

SOURCE: 97 Silverado K1500 350 VTEC 5.7 Stuck in 4 Wheel Drive

If it has the push button 4wd selector on the dash, it is most likely the transfer case encoder motor. Not to bad to replace but you will have to remove the front driveshaft.

Anonymous

  • 1 Answer
  • Posted on Nov 12, 2009

SOURCE: My 1996 full size chevrolet tahoe will not go into 4wd

check the solenoid on the front differential. i had a similar problem. when i would start to engage 4wd low/high and it would blow the fuse. i replaced the front solenoid and fixed my problem.

the solenoid can be found in the right side of the front differential. costs about $100 at local part store and takes 5-10 to changeout with an adjustable wrench.

Anonymous

  • 334 Answers
  • Posted on Dec 08, 2009

SOURCE: I have a 2001 Chevy 2500 4X4. Four wheel drive not

Sounds like the chain in the transfer case has broke or the linkage is out of adjustment

6bta

  • 400 Answers
  • Posted on Dec 23, 2009

SOURCE: front drive shaft/transfer case removal 03 chevy trailblazer 4wd

Sounds like you got it. They are heavy and ocward (spelling?). As for the front drive shaft take the bolts out and give it a couple of wacks with a dead blow hammer then slide it out. Maybe a few days before hand give it a good spray down with wd40 or like product. Also when you get to the last bolt for the t-case to trans loosen it half way then put a drain bucket under it and seperate it a little and let the trans fluid drain some, or you will be wearing it.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
3answers

My 1996 chevy 4x4 will not come out of 4wd

if its elect 4x4 check fuses .check to see if u r getting power to the moter on the transfer caseif u r getting power listen if u can here the moter working.if it is working then the spline has worn or broken remove the moter and put ur truck back into 2 wheel until u replace it
0helpful
1answer

My 98 chevy k1500 has the electonic push button 4 wheel drive that does not work i have replaced it but still get nothing shows power but does not enguage

there is a transfere case shift control module . (think it is under the passager side dash kick pannel ) this module recives a signal from the 4wd switch that tells it to shift the transferecase into 4wheel, there is also a motor on the trasferecase too . Now its hard to test these with out a scan tool because you need to see if each component is sending and recievcing the proper comand .
0helpful
1answer
0helpful
1answer

1996 chevy 1500 z71. Keeps blowing fuse when trying to use push button 4 wheel drive. Note: 4- Low and 4-Hi stay lit and blinking before fuse blows. New actuator. New switch on transfer case. New transfer...

Cheak all wiring, one little **** in the wire will make a fuse blow. I had the same problem with my starter and i replaced the starter but it was still blowing the fuse, come to find out it wus a wire burnt into so cheak all wires carfully.
1helpful
1answer
0helpful
2answers

Transfer case chevy truck

a np241 from a th400/4l80e would have the 32 spline that is need for a manual trans, one from a 700r4/4l60e is 27 spline input, in 94 the switch was changed and the cam to activate the switch was changed so if you get a 94 np241 you then will need to wire in a 94 switch into the older harness
1helpful
2answers

1989 Chevy Pick-up..when 4x4 engages it blowes THE FUSE!

I would replace the 4 x 4 actuating switch located top rear of transfer case. The switch has a 2 wire harness hooked to it. The same thing happened to mine. Cost me $80.00 and 30 minutes.
0helpful
1answer
1helpful
2answers

1996 chevy K1500 transfer case slipping out of 4 wheel drive

Your trouble is most likely not in the transfer case but in the front differential engagement solenoid.
Not finding what you are looking for?

90 views

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

john h

Level 3 Expert

29494 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...