I can't see how to get the air filter removed from a Plymouth voyger. Do you have to disconnect from the bottom once screws removed? Case doesn't seem to snap open.

Ejefferson, Crank case ventilation hose at link below $6 to $7.00.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
More Information for DORMAN 46013

More Information for DORMAN 46033

remove the passengers side lower kick panel, it's under the glove box. it has two T25 torx screws.
Disconnect the light and move it out of the way.
You'll see a large black cover underneath the whit a/c case. The black cover will have four T25 torx screws. Remove all four screws and the cover will come off.
remove the cabin filter by pulling it through the bottom.
pay attention to the orientation of the filter. it will only go in one way.


Reassemble the same way you took it apart.

chrysler voyger ,well our europeon models have a smaller engine and mainly diesel versions although i have seen a import with a V6 engine-once- Now firstly check the plug gaps 25th then the air filter then report back ,but another cause could be a faulty first in line O2 sensor but check the obvious first

Removal & Installation

1. Select the following settings:
   Turn the ignition ON Select Recirc in the OFF setting Turn the ignition OFF
   
2. Disconnect the negative battery cable.
3. Remove the wiper arm assemblies.
   CAUTION A sharp edge is revealed once the weatherstrip is removed.
4. Remove the weatherstrip at rear of the engine compartment.
5. Remove the cowl retaining nuts.
   
   
   

   Fig. Remove the cowl screen assembly
   

6. Remove the cowl screen assembly.
7. Rotate the locking tabs outward to release the filter assembly.
8. Remove the filter by lifting straight up.
   
   
   

   Fig. Remove the wiper module retaining bolts
   

9. Remove the wiper module retaining bolts.
10. Reposition the wiper module to the right.
11. Remove the filter housing attachment bolts.
12. Remove the filter housing.
13. Remove the blower motor housing:
14. Remove the blower motor housing screws
    
    
    

    Fig. Release the locking tabs and remove the fan housing
    

15. Release the locking tabs and remove the fan housing
16. Disconnect the blower motor electrical connector.
17. Squeeze the bottom of the connector and pull downward.
18. Remove the blower motor assembly by lifting straight out.

To install:

NOTE The fan motor assembly rib must be located into the channel in the module housing.

1. Install the blower motor assembly into the module housing.
2. Connect the blower motor electrical connector.
   NOTE The housing rib must fit into the slot in the HVAC module case.
3. Install the blower motor housing. Snap the left and right clip into place
4. Tighten the fan housing to blower motor housing screws to 9 inch lbs.(1 Nm).
   NOTE A new filter housing seal must be used whenever the filter housing is removed to prevent water from leaking into module.
5. Remove the filter housing seal using a small flat-blade screwdriver.
6. Install a new filter housing seal.
7. Install the filter housing.
8. Install the filter housing screws, and tighten the screws to 31 inch lbs.(3.5 Nm).
9. Position the wiper module.
10. Install the wiper module bolts, and tighten the bolts to 44 inch lbs.(5 Nm).
11. Install the passenger compartment air filter. Notice the air flow direction indicator printed on side of the filter.
12. Rotate the locking tabs on the filter housing inward to secure the air filter in place.
13. Install the cowl screen.
14. Install the cowl screen nuts, and tighten the nuts to 9 inch lbs.(1 Nm).
15. Close filter access door.
16. Install the weatherstrip at rear of the engine compartment.
17. Install the wiper arm assemblies.
18. Connect the negative battery cable.

1. Disconnect the blower motor electrical connector.
2. Remove the lower blower motor cover retaining screws.
   
   
   

   Fig. Remove the lower blower motor cover
   

3. Remove the lower blower motor cover.
4. Remove the blower motor nuts.
   NOTE Cut through the case as straight as possible because the motor cup must be replaced.
5. In order to prevent damage to the component, do not cut any deeper than necessary to remove the motor cup.
6. Remove the blower motor and cup from the lower case by cutting through the case between the circular ribs around the motor with a sharp utility knife.
7. Release the blower motor retaining tab and remove the motor from the cup.
   

To install:

1. Install the blower motor into the motor cup that was cut out of the lower case.
   
   
   

   Fig. Install the blower motor (1) into the motor cup (2) that was cut out of the lower case
   

2. Install the blower motor nuts, and tighten the nuts to 21 inch lbs.(2.4 Nm).
3. Attach the service ring to the motor cup with the screws included in the kit, and tighten the screws to 15 inch lbs.(1.8 Nm).
4. Install the blower motor and service ring into the HVAC module using the screws included in the kit. Make certain the blower motor electrical connector is pointing rearward in the vehicle, and tighten the screws to 15 inch lbs.(1.8 Nm).
5. Install the lower blower motor cover.
6. Install the lower blower motor cover retaining screws, and tighten the screws to 15 inch lbs.(1.8 Nm).
7. Connect the blower motor electrical connector.

Hope this helps (remember to rate and comment this).

REMOVE ENGINE COVER DISCONNECT MASS AIR FLOW SENSOR CONNECTOR.LOOSEN AIRDUCT FLOW TUBE SCREWS THEN REMOVE AIR FILTER COVER HOUSING BOLTS THEN RAISE AIR FILTER COVER UP SLIGHTLY ENOUGH SLIDE IT AWAY FROM AIRFLOW DUCT.THEN REMOVE COVER REPLACE AIR FILTER THEN PUT EVERYTHING BACK UP VISA VERSA DONT FORGET TO TIGHTEN SCREWS TO AIRFLOW DUCT TUBE ONCE AIR FILTER HOUSING BACK IN PLACE.

1. Loosen the four screws that hold down the top of the air filter box. 2. Loosen the clamp that attaches the air filter box to the intake hose. 3. Disconnect the air sensor connector from the top of the air filter box. Note: Secure the connector wire, it tends to drop down and more than once I have had to remove the air filter box to retrieve it. 4. Remove the top part of the air filter box. You may need to twist it to get it to release from the rubber air inlet Hose.
5. Remove the two bolts holding the bottom of the air filter box. 6. Remove the bottom part of the air filter box.
7. Disconnect the negative then the positive battery cables.
8. Remove the three bolts that hold the brace that goes over the Windshield washer tank. 9. Remove the brace.
10. Remove the Battery hold down clamp at the base of the battery.
11. Remove the two nuts that hold the fuse box to the fender well. 12. Remove the two fasteners from the front of the widshield washer tank. 13. Rotate the windshield washer tank away from the battery. You may need to move the tank and lift the fuse box to get the tank clear of the battery. 14 Remove the battery.
To Install reverse the steps.
Time: 5 to 10 Minutes

There are two filters.
You have the remove the glove box. Three screws on the bottom edge. Remove them, then open the glove box door. Three plastic covers along the top edge, remove with something that won't cut them up. Remove screws under them (two screws under the center one). Then, push the glove box hinges toward each other to disengage the clips in the dashboard. Then pull the glove box assembly down and out (when the box is part way out, disconnect the glove box light connector before you take it the rest of the way).
Once the glove box is out, remove the three screws (two on the right, one on the left) of the glove box reinforcement panel, then remove the panel (the bar looking thing next down from where you took the three screws out of the bottom of the glove box).
Release the snap at the bottom and remove the air conditioning filter lid.
Slide the upper and lower filter assemblies out of the evaporator housing.
Remove the old filters from the filter carriers, clean the carriers and inset the new filters.
Reverse procedure to install.
I know that this sound involved, but just take your time, and you can do it.
Hope this helps you.

FUEL FILTER IS LOCATED ON TOP OF FUEL TANK..YOU MUST DROP FUEL TANK SLIGHTLY TO REMOVE LINES FROM FUEL PUMP UNIT..1 BOLT HOLDS IT TO TANK..2 CONNECTIONS AT TANK..1 AT LINE ON FRAME IN FRONT OF TANK

In most cases this problem is caused by the rotating ribbon circuit contact under the steering wheel having a broken filament, the part is known as a clock spring contact, u will need to properly disarm the airbag and remove the steering wheel to access the part. WARNING: Failure to follow factory Airbag disarming protocol can result in an unexpected Airbag deployment and possible serious personnel injury or death.

THE FUEL FILTER IS INSIDE THE GAS TANK.