Check engine light dont come on but is throwing multiple code misfiring in 1,3, and 4 cylinder says o2 sensor no activity and crank position sensor a circuit where is crand position sensor located

0339 is intermittand crank position pulses. That'll do it!
Check for bad connections/replace the sensor if faulty.

do you want gue$$ or how to test using TOOLS?
4 engines but told it YEAH. 3.2L
check all fuses first. a 20cent part, we test them 1 of 3 ways (ask)
flashing CEL means , CATS are going to run way too hot and may be damaged, means dont drive it far.

you failed to tell the 4 O2 DTC errors..
there are 2 kinds, heater or sensor out (cell) voltage
which one is key to the problem why do that>?
O2 sensors all 4 failing to me (blind) smacks of heaters shorted. (or the wires to them 1 wire shorted can short them all out) and is never good this.
you have p0300 errors to, ? or just 1 code p030x
where x is a number 1 to 6 and is always the same exact number, again no DTC told just vague.
questions all I have are those, blind must ask them ok.?
ever get a full tuneup 19 years.?
for sure spark plugs and filters and fan belt.(serp)
on this 3.2L the O2 heaters shorted blow 2 fuses
pre O2 or Post 02 fuses. so seems not this. hoodbox

ESP mind meld 1:
misfire codes P030x (x = 0 to max or 6)
if one fails it means that cylinder # has weak
combustion. or if p0300 all are.
caused by
that cylinders is bad, (example burned head valves)
and low compression tests (below 150psi) or vacuum test gauge shows, vacuum bouncing like mad,. oops
bad engine.

or bad spark (never did a tune up here ,bingo)
and last bad fueling if fuel is too lean on all 6
we see po300 and lean burn codes p017x or LTFT long term fuel trim way off at +xx huge %
or too rich fuel and misfires (on all or just 1 cyl)
or just one injector is dead , leaks or is 1/2 clogged

lacking any list of all DTC failing,all i can do is say how to do the tests. (engine,spark ,fueling)
scan the PCM
write down all DTC found
and share them all, skip none..

code p 0141 refers to heated oxygen sensor (HO2S) 2 bank 1--heater control--circuit malfunction===causes --wiring---HO2S--- ECM
code p 0144 refers to heated oxygen sensor(HO2S) 3 bank 1--high voltage ===causes wiring short to positive ---HO2S---ECM
also refers to oxygen sensor(O2S) 3 bank 1--high voltage ===causes wiring short to positive---O2S-- ECM
HO2S sensors are the units in the exhaust manifolds or before the cat converters
O2 sensors are after the cat converter
two completely different operations
use the special tool for sensors as the wires are easily damaged from the wrong tool use
as for misfiring you will get a P0300 (0300,0301,0302,0303 etc) depending on which cylinders are misfiring
when checking for misfiring the injectors , (blocked or not firing) are as important as plugs and wires
If the misfiring continues after sensor replacement , replace the ECM with a known good one as it is common to all fault codes and misfiring

P0300 Random/Multiple Cylinder Misfire Detected P0301 Cylinder 1 Misfire Detected P0302 Cylinder 2 Misfire Detected P0303 Cylinder 3 Misfire Detected P0304 Cylinder 4 Misfire Detected P0305 Cylinder 5 Misfire Detected P0306 Cylinder 6 Misfire Detected P0307 Cylinder 7 Misfire Detected P0308 Cylinder 8 Misfire Detected P0309 Cylinder 9 Misfire Detected P0310 Cylinder 10 Misfire Detected P0311 Cylinder 11 Misfire Detected P0312 Cylinder 12 Misfire Detected P0313 Misfire Detected with Low Fuel P0314 Single Cylinder Misfire (Cylinder not Specified) P0315 Crankshaft Position System Variation Not Learned P0316 Misfire Detected On Startup (First 1000 Revolutions)

Read more at: http://www.obd-codes.com/trouble_codes/
Copyright © OBD-Codes.com
-----------------------------------------------------------------------
P2195 O2 Sensor Signal Stuck Lean Bank1 Sensor 1 P2196 O2 Sensor Signal Stuck Rich Bank1 Sensor 1 P2197 O2 Sensor Signal Stuck Lean Bank2 Sensor 1 P2198 O2 Sensor Signal Stuck Rich Bank2 Sensor 1

Read more at: http://www.obd-codes.com/trouble_codes/
Copyright © OBD-Codes.com http://www.obd-codes.com/p0002

Check Engine Light Codes and Meanings
Long blinks Short blinks Problem
1 1 Camshaft position sensor
1 2 Mass air flow sensor
1 3 Engine coolant temperature sensor
1 4 Speed sensor
1 11 EVAP control system (flow)
1 14 Fuel injection system right bank (too rich)
1 15 Fuel injection system right bank (too lean)
2 1 Ignition circuit
2 3 Closed throttle position switch
2 5 Idle speed control
2 9 Fuel Injection system left bank (too rich)
2 10 Fuel Injection system left bank (too lean)
3 1 ECU
3 2 Exhaust gas recirculation system flow problem
3 3 Front left O2 sensor
3 4 Knock sensor
3 5 Exhaust gas recirculation temperature sensor
3 6 EGRC-BPT valve
3 7 Closed loop control
3 8 Closed loop control
4 1 Air intake temperature sensor
4 2 Fuel tank temperature sensor
4 3 Throttle position sensor
4 7 Crankshaft position sensor
5 3 Front right O2 sensor
5 4 Automatic transmission control unit
6 3 Cylinder #6 misfire
6 4 Cylinder #5 misfire
6 5 Cylinder #4 misfire
6 6 Cylinder #3 misfire
6 7 Cylinder #2 misfire
6 8 Cylinder #1 misfire
7 1 Multiple cylinder misfire
7 2 Three way catalytic converter (right side)
7 3 Three way catalytic converter (left side)
7 4 Evaporative emission control system pressure sensor
7 5 Evaporative emission control system
7 7 Rear O2 sensor
8 1 Vacuum cut valve bypass valve
8 2 Crank position sensor
8 3 Absolute pressure sensor
8 4 Automatic transmission control unit
8 6 Evaporative emission canister purge control solenoid valve
8 7 Evaporative emission Canister purge control solenoid valve circuit
9 1 Front Right O2 sensor
9 3 Evaporative emission Canister vent control valve
9 5 Crankshaft position sensor
9 8 Engine coolant temperature sensor
10 1 Front left O2 sensor
10 3 Park and Neutral position switch
10 5 EGRC solenoid valve
10 8 Evaporative emission canister purge volume control valve
11 1 Inhibitor switch
11 2 Revolution sensor
11 3 Improper shifting to first gear (Automatic transmission)
11 4 Improper shifting to second gear (Automatic transmission)
11 5 Improper shifting to third gear (Automatic transmission)
11 6 Improper shifting to fourth gear (Automatic transmission)
11 7 Solenoid valve lock up function
12 1 Shift solenoid B (Automatic transmission)
12 3 Overrun clutch solenoid valve (Automatic transmission)
12 4 Torque converter clutch solenoid valve (Automatic transmission)
12 5 Line pressure solenoid valve (Automatic transmission)
12 6 Throttle position sensor (Automatic transmission)
12 7 Engine speed signal
12 8 Fluid temperature sensor
13 2 MAP/BARO Switch Solenoid Valve
13 5 Fuel pump control module
13 8 Cooling fan

Hello your po135 is o2 sensor bank 1 your po141 is O2 sensor bank 1 sensor 2 and your pO300 is random multiple cylinder misfire these problems are your oxygen sensors and engine misfire pO300 is you engine missing o2 sensors are switches in the exhaust system the engine misfires are the engines cylinders missing.

Well, it is either a timing belt/chain going out or a bad crank position sensor most likely causing the other problems. The O2 sensor may be bad as well but that usually doesn't cause the Misfire. The vehicle on board computer is confused, that is why it is throwing all those codes. and why it gives you that 1166 code which isn't defined. Check the crank position sensor and the timing and timing belt first. Once you have that fixed the rest should clear up.

Generic OBD II Diagnostic Trouble Codes

DTC CODES P0300 to P0399

P0300....Random/Multiple Cylinder Misfire Detected

P0301....Cylinder 1 Misfire Detected

P0302....Cylinder 2 Misfire Detected

P0303....Cylinder 3 Misfire Detected

P0304....Cylinder 4 Misfire Detected

P0305....Cylinder 5 Misfire Detected

P0306....Cylinder 6 Misfire Detected

P0307....Cylinder 7 Misfire Detected

P0308....Cylinder 8 Misfire Detected

P0309....Cylinder 9 Misfire Detected

P0310....Cylinder 10....Misfire Detected

P0311....Cylinder 11 Misfire Detected

P0312....Cylinder 12 Misfire Detected

P0313....Misfire Detected with Low Fuel

P0314....Single Cylinder Misfire (Cylinder not Specified)

P0320....Ignition/Distributor Engine Speed Input Circuit

P0321....Ignition/Distributor Engine Speed Input Circuit Range/Performance

P0322....Ignition/Distributor Engine Speed Input Circuit No Signal

P0323....Ignition/Distributor Engine Speed Input Circuit Intermittent

P0324....Knock Control System Error

P0325....Knock Sensor 1 Circuit (Bank 1 or Single Sensor)

P0326....Knock Sensor 1 Circuit Range/Performance (Bank 1 or Single Sensor)

P0327....Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)

P0328....Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)

P0329....Knock Sensor 1 Circuit Input Intermittent (Bank 1 or Single Sensor)

P0330....Knock Sensor 2 Circuit (Bank 2)

P0331....Knock Sensor 2 Circuit Range/Performance (Bank 2)

P0332....Knock Sensor 2 Circuit Low Input (Bank 2)

P0333....Knock Sensor 2 Circuit High Input (Bank 2)

P0334....Knock Sensor 2 Circuit Input Intermittent (Bank 2)

P0335....Crankshaft Position Sensor A Circuit

P0336....Crankshaft Position Sensor A Circuit Range/Performance

P0337....Crankshaft Position Sensor A Circuit Low Input

P0338....Crankshaft Position Sensor A Circuit High Input

P0339....Crankshaft Position Sensor A Circuit Intermittent

P0340....Camshaft Position Sensor 'A' Circuit (Bank 1 or Single Sensor)

P0341 Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 1 or Single Sensor)

P0342....Camshaft Position Sensor 'A' Circuit Low Input (Bank 1 or Single Sensor)

P0343....Camshaft Position Sensor 'A' Circuit High Input (Bank 1 or Single Sensor)

P0344....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 1 or Single Sensor)

P0345....Camshaft Position Sensor 'A' Circuit (Bank 2)

P0346....Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 2)

P0347....Camshaft Position Sensor 'A' Circuit Low Input (Bank 2)

P0348....Camshaft Position Sensor 'A' Circuit High Input (Bank 2)

P0349....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 2)

P0350....Ignition Coil Primary/Secondary Circuit

Given that most of the trouble codes are for the O2 sensor, I think I would change it. The multiple misfires could be because of improper fuel/air mixture caused by a bad sensor. Disconnect the negative(-) battery terminal then change the sensor. Disconnecting the negative(-) should reset the computer and allow the fuel/air mixture to return to default allowing the engine to start.
P0130 - O2 Sensor Circuit Malfunction (Bank 1 Sensor 1)
P0134 - O2 Sensor Circuit No Activity Detected (Bank 1 Sensor 1)
P0135 - O2 Sensor Heater Circuit Malfunction (Bank 1 Sensor 1)
P0141 - O2 Sensor Heater Circuit Malfunction (Bank 1 Sensor 2)
P0300 - Random/Multiple Cylinder Misfire Detected

P0137--O2 Sensor Circuit Low Voltage-Bank 1 Sensor 2

P0139--O2 Sensor Circuit Slow Response-Bank 1 Sensor 2

P0152--O2 Sensor Circuit High Voltage-Bank 2 Sensor 1

P0300--Random Multiple Cylinder Misfire


I would suspect that the camshaft position sensor is bad. This is a quote from the tech manual:

The Powertrain Control Module (PCM) uses the camshaft position sensor to manage sequential fuel injection and as part of misfire diagnosis. The PCM constantly monitors the number of pulses on the signal circuit. The PCM compares the number of camshaft sensor reference pulses and the number of crankshaft position sensor reference pulses received. If the PCM receives an incorrect number of pulses, Diagnostic Trouble Codes (DTCs) should be stored in the PCM. Some PCM systems will then default to multi-port or "gang-fire" injector operation. The camshaft position sensor signal is required to sequence the injector operation to the proper cylinder timing. If the camshaft position sensor or circuit is faulty, most engines will start. However, the PCM misfire diagnostic will likely be affected.



The part costs $50.....simple to change. It is NOT the O2 sensors so don't go wasting money on those. They are being affected due to related symptoms....they fault because the problem is happening upstream.