Changing rear rotors

Check if the parking brake is not keeping the rotor from coming off. you will need to back off the parking brake. it is like the old drum brakes. inside the rear rotors.

. Removal & Installation Front Front brake caliper & rotor removal/installation

Rear Rear brake caliper & rotor removal/installation

Yes, it has rear Disc Brakes, I would suggest to change the rear pads since they have to remove the rear Brake Calipers to remove the rotors and it wouldn't take much more time or labor to replace the pads at that point. That way when your rear rotors are re-installed and your new brake pads are installed your rear brakes should give you longer service life and better stopping power.

Rear disc brake pads offer better performance and are not as affected by moisture like conventional brake shoe style brakes are. Rear disc brakes are similar to front disc brakes. The main difference is that rear disc brake systems must incorporate the emergency brake system. There are two methods widely used for the emergency brake with rear disc systems. The first system is a brake shoe inside the brake disc that is actuated by the emergency brake lever. The second is a screw style actuator inside the brake caliper. When activated the brake pads are forced into the brake disc and held tightly by the emergency brake lever.
READ COMPLETELY BEFORE STARTING
Step 1 - Identify Rear Disc Brake Components
Rear disc brake assembly includes; rear brake disc, rear brake pads, brake caliper mount and a caliper mounting screw. (Note: Some vehicles do not have the rotor mounting screw.)
Step 2 - Removing the Rear Brake Caliper Mount Bolts
To replace rear brake pads and rotors the rear brake caliper needs to be removed. First loosen the rear brake caliper mount bolts and remove them. Turn counter clockwise.
Step 3 - Lift Rear Brake Caliper from The Caliper Mount
After the caliper mount bolts have been removed, gently lift the brake caliper from the caliper mount. Inspect the caliper slides; they should move freely in the caliper mount. Remove rear brake pads and hardware.

Step 4 - Removing Caliper Mount Bolts
With a socket wrench or other appropriate removal tool, loosen the rear brake caliper mounting bolts. Remove bolts and lift the caliper mount and remove it from the vehicle. Remove the retaining screw from the disc mounting hole. Tap the rotor gently to release any rust that has accumulated between the rotor and bearing hub. Lift brake rotor from wheel hub holding on tightly, using both hands. You do not want to drop the rotor.

Step 5 - Removing Rear Brake Rotor
Remove the retaining screw from the disc mounting hole, tap the rotor gently to release any rust that has accumulated between the rotor and bearing hub. Lift brake rotor from wheel hub, hold on using both hands and do not drop.

Step 6 - Install New Brake Rotor
Check the new rotor against the old brake rotor to make sure they are the same size. Clean the mating surface on the wheel hub before the new brake rotor is installed. Reinstall rotor retainer screw.
Step 7 - Reset Rear Brake Caliper
Before new brake pads can be installed, the rear brake caliper must be reset. The reset tool winds the piston back into position so the new brake pads will fit. This style of brake caliper will not compress with a clamp tool; it can only be reset with the proper reset tool.
Step 8 - Reinstall Rear Caliper Mount and Install New Rear Brake Pads
After the caliper has been reset, reinstall caliper mounting bolts and make sure the bolts are tight. Then match up the old brake pads to the new brake pads. They should be exactly the same except, of course; the old ones will be worn out. Check the new brake pads for proper fit and install any brake hardware that is required.
Step 9 - Remount Rear Brake Caliper
Reinstall the brake caliper, align brake pad hardware and reinstall caliper mounting bolts. (Note: align the rear peg of the brake pad to the groove in the caliper piston.) Recheck and retighten all caliper and caliper mount bolts. Bleed brake system to relieve any air in the system. Before driving the vehicle, push the brake pedal down and let it up slowly. This operation forces the brake pads to travel to the brake rotors. DO NOT DRIVE VEHICLE until proper brake pedal operation resumes. When test driving vehicle listen for any unusual noises during the operation of the brakes.
WARNING! Always have the vehicle under inspection on level ground, in park with the emergency brake on. Always wear protective eyewear, gloves and necessary clothing before inspection or work begins. Never crank an engine over when anyone is near the battery or engine. Always have an operational fire extinguisher close by, obey all first aid instructions in the event of an injury. Never stand in front or behind a vehicle when cranked over or running. When engine is cranked over keep hands and clothing away from rotating components. Never move a car without proper brake pedal operation.

-Set up jack and properly block front tires.

-Do not set parking break as this may hender removing the rear calipers. Open hood and remove the brake resevoir cap.

-Remove hubcaps if applicable,

-Loosen Lugnuts but do not remove,

-Jack up van,

-Remove tire.

-Caliper should be visible. There are two bolts or hex heads on the back side that can be a pain to remove sometimes.

-Pull the caliper off the rotor, It is recomended to have the rotors turned or replaced. With the old pad still in place, take a c clamp or brake caliper squeezer and compress the caliper

-remove old pad, take note for the reinstall of the new pad.

-reverse the steps. This is a simple break down. Hope it helps

take tire off, remove drum , hammer out old one. with nut and spacers turn nut to pull stud in hole.
If vehicle has rotor. remove tire, remove brake caliper, remove center axle nut, remove rotor. hammer out old. install new one

remove the wheel, use a large c-clamp to bottom out the caliper pistons,remove the caliper bolts,remove the caliper, hang it from a coathanger to protect the brakeline, unbolt the rotor and, remove

Just remove the rear rotors, bull the straight off, after removing the caliper bracket. It would be a good idea to spray the small brake shoes with brake cleaner. No need to remove anything other than the rotor.

Be very careful as my 75 year old pappy taught me this trick..... take of the wheel, make sure the rear of the vehicle is off the ground (both sides). Re affix 3 lugs back on the bolts (about 1/2 way tuened down). Start the vehilce and place in drive -spin the rear wheels and the force will cause the rotor to loosen against the lugs.

Remove rear wheels, remove rear calipers there will be two ten or 13 mm bolts on the back,(DO NOT LOOSEN THE LITTLE BLEEDER NIPPLE WITH THE RUBBER CAP ON IT!) pry the calipers back and off the rotors ,remove the old pads and get a c-clamp or big channel lock pliers and squeeze the caliper pistons back into the bores until they stop, now if your rotors are badly scored or rusty this is the time to change them there will be one or two #3 phillips head screws holding each rotor, remove these( you may need an impact driver with a phillips bit and a hammer) pull off the old rotors and reinstall the new ones after cleaning the rust protection off of them with brake cleaner and cleaning the rust from the hub where they sit., pull the rubber boots back on the caliper slide pins and lube them with clear silicon grease till they move freely, now use black hi temp grease to lube where the pads sit on the brackets(after cleaning the brackets of rust and dirt) and lube the backs of the pads (not the friction side make sure these stay clean!!) now reassemble and enjoy you just saved yourself a couple hundred bucks from the shop !! -jeff