Question about BMW 328

1 Answer

Roll over bars released. reset down what rearms them?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • BMW Master
  • 1,675 Answers

hi its just spring activated, just follow instructions below to reset the roll bar1. Raise rear headrest to its highest possition
2. With a screwdriver, remove the plastic cover that is located under the headrest between the roll-bar.
3. Reach down into the opening to locate the metal tab that has locked the spring loaded roll-bar into place.
4. Simultaniously push the tab in (towards the front of the car ) while pushing downward on the top of the exposed roll-bar to compress the springs. Push all the way down until the bar locks into place.
hope this helps please comment and rate thanks

Posted on Feb 03, 2011

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2003 Cadillac CTS NONE OF MY WINDOWS WANT ROLL DOWN OR UP NOT WILL THE TRUNK OPEN WITH THE RELEASE BUTTON


look in fuse panel find window relay and or fuse replace. then disconect battery for 30 secs to reset computer.

Apr 03, 2012 | 2003 Cadillac CTS

4 Answers

I HAVE A 1995 M B 500 SL THE SWITCH INDICATOR FOR THE TOP & ROLL BAR STAY IN A BLINKING POSITION. THE TOP, POWER WINDOWS AND ROLL BAR WILL NOT FUNCTION AT ALL... THANK YOU


The control module has set a fault and it will have to be reset. They are sensitive to voltage & must have 12 volts to operate properly.
The windows and top will need to be resync. I cannot find any information regarding the diagnostic procedure for the roof .. it states there is a procedure to diagnose the fault with the number of flashes the switch makes .. a dealer may be your best option on this fault .. I hope this helps some.

Aug 26, 2011 | Mercedes-Benz CL500 Cars & Trucks

1 Answer

My roll bars (back seat head rests) are stuck in the UP position and I can't close the top while they are up. How do I get them down mechanically, the guide shows plenty of info for the top but nothing...


just push the roll bar button in the up position like you raising the roll bar. hold it for about ten seconds or til you hear a click sound. basically your just going to reengage the mechanism again since the roll bar got deployed while driving. If thats not the case then you might have a separate problem but I would start there.

Sep 28, 2010 | 2000 Mercedes-Benz CLK

1 Answer

2004 JAGUAR XKR CONV. THE PASSENGER WINDOW GOES DOWN WHEN DOOR IS OPENED BUT ROLLS BACK UP WHEN THE DOOR HANDLE IS RELEASED. IS THERE A RESET OR IS THE LATCH FAILING


Voltage fluctuations with a weak battery etc can cause loss of window memory. Start car, lower windows and hold the switch down for several seconds then repeat in the raised position. This will reset window positon memory.

Sep 16, 2009 | 2004 Jaguar Xkr

2 Answers

My convertible top will not operate. what can i


I have 1997 mercedes benz sl500 after changing my battery, my roll bars will not go down. how do I get my roll bar back down?

Aug 13, 2009 | 1998 Mercedes-Benz SL-Class

1 Answer

While putting the top up the spring loaded roll bars popped up


Hi , there is a special tool required to release the mechanism catch so you can push the roll over protection bars back to the opperation position , if you have a local dealer to you, they should be able to reset them at little or no cost , hope this helps , regards mark .

Jul 19, 2009 | 1998 BMW 3 Series

1 Answer

ROLL bar malfuntion. Roll bars will not go down. Is there a reset button?


This system is designed to release the roll bar from the actuating rams due to input from the axle(suspension travel) sensors in the rear of your vehicle. More than likely your roll bar system released the bar and it sprung upwards. You have to hold the roll bar switch in the up position until the rams travel up and lock back into the bar. Once they lock back in the system will be operational again.

Jun 27, 2009 | 2000 Mercedes-Benz CLK

2 Answers

I own a 1995 mercedes SL500 and recently started having trouble with the left front door window. While stopped in a construction zone, I rolled both windows down. After leaving the construction area, I...


The window position is monitered by the softop control module. It sounds like the glass is very dirty and drawing too much amperage during window operation. The soft top is electro hydraulic. The roll bar is operated normally with hydraulics but it is mechanically released in an emergency situation. 1st make sure your windows are clean and the express(one touch operation) is working-the soft top will not function properly if the windows are not synchronized. Next be sure your roll bar works-hold swith in up position to lock roll bar rams in if they have been deployed. next put your top all the way up. untill windows roll up and try it with the engine running and trans in nuetral- if it still does not work mechanically secre rear of top with tool provided in your tool kit the owner's manual will tell you how to do this. good luck

Jun 19, 2009 | 1995 Mercedes-Benz SL-Class

2 Answers

Roll bar on clk 320 cabrio


I have a 2005 CLK 320. Roll bars deployed on a bump with the top up. Here's how to fix it: There is a reset port about 12 in below each headrest. The port is hard to find, but you can actually glimpse it with good light and/or a flashlight and some head/neck contortion. When facing forward the port is on the left side of each headrest. The port is oval in shape, about 4mm x 8mm, positioned about 10 mm forward of the support post and about 5mm to its left. Essentially, its an oval hole in black sheet metal. Mercedes mentions an allen key tool included with the car, but you can use a very long screwdriver or, preferably, a metal shishkabob barbecue skewer (by far the best) to reset the mechanism. Slide the tool (skewer, screw driver or allen key) straight down along the side of the headreast and then very carefully angle the tip forward and to the left (of car) to go into the port. Again, you can see this if you try. Push down on the spring under the port and hold down while you push down (Hard) on the headrest to its full reset position. Then remove the tool. Voila!

Before the reset, the top would not go down. After the reset, no problemo. Dennis

Jun 26, 2008 | 2000 Mercedes-Benz CLK

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

272 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

stephen Kiarie
stephen Kiarie

Level 1 Expert

32 Answers

Roy Cunningham

Level 1 Expert

35 Answers

vince

Level 3 Expert

1234 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...