At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
? 5:02
https://www.youtube.com/watch?v=Xl8B78vBDXk
Jul 8, 2015 - Uploaded by World Mechanics
Chrysler PT Cruiser Dash Lights Instrument Cluster lights ON & OFF Blinking COMMON PROBLEM! We took ...
? 3:03
https://www.youtube.com/watch?v=S1dFuACAMk0
May 9, 2013 - Uploaded by 2stroketurbo
A quick overview of how to replace burned out dash lights on a 2005 ... How To Install Replace Engine Ignition ...
The trouble light is in the instrument cluster.behind dash gauges.,BE SURE TO DISCONNECT BATTERY BEFORE REMOVING ANY PART OF DASH..Use safety glasses.,The cluster is attached to the back of gauges..Be VERY CAREFUL If you remove it ..Very Fragile and easy to damage..!!....Older vehicles have a more simple cluster with bulbs that can be replaced or removed..Or leave out and never have a trouble light again..I doubt if your vehicle has a simple bulb however it is possible...If you just wanted the light to go off forever there is a chance you could remove the cluster and it will have a simple small removable bulb..I would ask a Dealer Tech....The cluster is like a map or a weird racetrack..lights for each instrument are located on the pathway...You may could crush the tiny area where light is if it doesn't have a bulb that can be removed but it may interfere with other lights on the cluster pathway or perhaps DISABLE THE COMPLETE CLUSTER..I DONT RECOMMEND CRUSHING ANY PART OF CLUSTER.!!,,However I have seen it done..Some lights are made into the pathway and can't be removed and some are just removable bulbs..Your vehicle could have both type pending on location of your problem light..I have seen many replaceable bulbs located at the bottom of instrument clusters on Heavy Ford Trucks.., however the center lights cant be replaced..Especially if it is all digital..!!..Look for a close up photo of the rear of your instrument cluster on a computer and you will see what I am describing...You may just have a very small plug in bulb..It may be a good idea to ask a Dealership Tech.....Good Luck...
Which light is out? Is it an instrument cluster light, or one on the temperature or A/C cluster? It it's an instrument cluster light, here is the process: (I'm assuming the 99 is similar to the 98) Remove the bottom dash panel under the steering wheel, remove the instrument cluster cover around the steering column. This will reveal the screws that hold your instrument cluster cover in place. Remove this cover and you can then see and remove the 4 screws holding your instrument cluster in place. Pull your instrument cluster out, remove the main wire connector, then you have access to all the instrument cluster lights on the back side. Hopefully you remember which one is out!
Remove the bulb from its retaining clip contacts. If the bulb has
tapered ends, gently depress the spring clip/metal contact and disengage
the light bulb, then pull it free of the two metal contacts.
To install:
Before installing the light bulb into the metal contacts, ensure
that all electrical conducting surfaces are free of corrosion or dirt.
Insert the bulb into the holder. If the contacts have small holes,
be sure that the tapered ends of the bulb are situated in them.
To ensure that the replacement bulb functions properly, activate
the applicable switch to illuminate the bulb which was just replaced. If
the replacement light bulb does not illuminate, either it is faulty or
there is a problem in the bulb circuit or switch. Correct as necessary.
Install the cover until its retaining tabs are properly engaged.
Connect the negative battery cable.
Instrument Cluster Light Bulbs The instrument
clusters installed on these models are one of 2 types and distinguished
by the instrument lighting color, either green or blue. On models
with green instrumentation, only the control light bulbs are
replaceable. Should any other failure occur, the instrument cluster must
be replaced. On models with blue instrumentation, none of the
components are replaceable. Should a failure occur, the instrument
cluster must be replaced.
You will have to replace the light bub within the instrument cluster. First remove the instrument cluster cover (two bolts at the top 7 mm) then remove the 4 bolts securing the cluster to the instrument panel (7 mm) and you should be able to pull out the cluster, disconnect the three wire harnesses with a screwdriver, your light bulb is at bottom, twist to remove your old and twist to install the new.
Try to remove the instrument panel and disconnect the harness to see if doing that gets rid of the blown fuse when starting the car. If it does, then the instrument panel should be replaced with another. If the fuse still blows when starting, then there is a wire shorted to ground somewhere.
--- Instruments and SwitchesInstrument ClusterRemoval & InstallationTo Remove:
Remove the instrument cluster trim plate.
Remove the instrument cluster mounting screws.
Rotate the instrument cluster rearward and lift up on the top of the cluster in order to disengage the locating pins.
Disconnect the electrical connectors from the instrument cluster.
Remove the instrument cluster.
To Install:
Connect the electrical connectors to the instrument cluster.
Position the locating pins to the holes in the instrument panel.
Install the instrument cluster by rotating the top inward.
Remove the 5 mounting screws from the instrument cluster trim plate and remove the trim plate. Remove the 4 mounting screws from the instrument panel face plate and remove the face plate.Remove the instrument light grid from the center of the cluster. From behind the instrument cluster reach behind the speedometer and disconnect the speedometer cable by releasing the tab. Pull the cluster forward just enough to detach the "check engine" light bulb from the center of the cluster. Remove the instrument cluster from the dashboard.
Difficult to explain step by step. You need yo remove the instrument cluster. If youre technically minded its not very hard, start by loosening the Phillip"s head screws that is visible on the panel directly under the instrument cluster, give it a try!
The light behind myRemove the cluster bezel from the instrument panel. See Cluster Bezel in this group for the procedures. Remove the four screws that secure the instrument cluster to the instrument panel Instrument Cluster Remove/Install Pull the instrument cluster rearward to disengage the two self-docking wire harness connectors NOTE: The instrument cluster has two self-docking wire harness connectors that will be automatically aligned with, and connected to the instrument panel wire harness when the cluster is installed in the instrument panel. Remove the instrument cluster from the vehicle. Reverse the removal procedures to install. Tighten the mounting screws to 2.2 N·m (20 in. lbs.) when I turn my headlights on. All the other gauges are lit, but not the gas gauge. How do I get in there to replace the bulb and fix this? Or is it a fuse problem? I have a 1998 jeep scout Thanks
×